•When you switch from “L or R” to “L+R,” choose which adjustment of the R and L channels to be applied.
1Select either “L 
R” or “R 
L” by rotating the [Rotary encoder], and press the [Rotary encoder].
L 
R: The adjustment of the L channel is to be applied to both R and L channels.
R 
L: The adjustment of the R channel is to be applied to both R and L channels.
9 Select the channel you want to adjust by pressing [CHANNEL].
L+R selected: FRONT HIGH 
FRONT MID 
FRONT LOW 
REAR 
CENTER 
SUBWOOFER*1 
FRONT HIGH
L or R selected: FRONT L HIGH 
FRONT R HIGH 
FRONT L MID 
FRONT R MID 
FRONT L LOW 
FRONT R LOW 
REAR L 
REAR R 
CENTER 
SUBWOOFER*2 
FRONT L HIGH
*1 If the Subwoofer output is set for Monaural, you can set both SUBWOOFER 1 and 2.
*2 If the Subwoofer output is set for Monaural, you can set SUBWOOFER 1 and 2. If the Subwoofer output is set for Stereo, you can set SUBWOOFER L and R.
•Channels to be set vary depending on the system set in “Setting the Speaker System (System Select)” (page 37).
10 Adjust the calculated time correction value (0.00 to
20.00 ms) by rotating the [Rotary encoder].
Displaying the distances from the listening positions to the speakers
Setting contents: 0.00 to 20.00 ms (in 0.05 ms steps)
•The distances can be displayed in either “cm” or “inch” (see “Setting the Time Correction Adjustment Unit (TCR Parameter)” page 51).
11 To adjust another channel, repeat Steps 9 through
10.
•You can listen with Defeat OFF (adjusted setup values) or with Defeat ON (Initial value) to compare, by following the steps below.
1Press and hold the [Rotary Encoder] for at least 2 seconds while in the adjustment mode.
2Rotate the [Rotary Encoder] to switch on/off Defeat, and listen to compare.
3To exit, select “OFF” and then press [
].
•You can mute the channel you are adjusting.
1Press [MUTE] while in the adjustment mode to mute the channel.
2To cancel muting, press [MUTE] again.
From the Commander
12 When the setting is complete, press and hold [
] for at least 2 seconds.
•If [
] is pressed during setting, the unit returns to the previous item.
•This function is not available when Defeat is set to ON.
•When the speaker is set to the “OFF” mode, the time correction for that speaker cannot be set. Refer to “Setting the Speaker System (System Select)” (page 37)/“Setting the Speakers (Speaker Setup)” (page 38).
•After the setting, it is recommended to store the setting contents on the unit. For details, refer to “Storing the Preset Values (Preset Store)” (page 36).
Setting the Time Correction Adjustment Unit (TCR Parameter)
The unit of measurement for time correction can be set as either “cm” or “inch.” (Initial setting: “cm”)
1 Press [FUNC.].
2 Rotate the [Rotary encoder] to select “Sound Field Adj.,” and then press the [Rotary encoder].
3 Rotate the [Rotary encoder] to select “Setup,” and then press the [Rotary encoder].
4 Rotate the [Rotary encoder] to select “TCR Parameter,” and then press the [Rotary encoder].
5 Select either “cm” or “inch” by rotating the [Rotary encoder], and press the [Rotary encoder].
cm: The unit for the time correction becomes “cm.”
inch: The unit for the time correction becomes “inch.”
6 When the setting is complete, press and hold [
] for at least 2 seconds.
•If [
] is pressed during setting, the unit returns to the previous item.
