46-EN
01GB07PXAH800.fm
ALPINE PXA-H800_EN 68-13530Z65-A (B5)
From the Commander
9
Select the level you want by rotating the [Rotary
encoder], and press the [Rotary encoder].
Compressed 1 to 3:
This corrects information lost in the compression process. This
reproduces a well-balanced sound close to the original. By
supplementing mid- to high- frequency sound data, the sound is
reproduced with more brightness and ambience.
Music 1 to 3:
Lower register sounds (drums, bass, etc.) and vocals are
emphasized for clean and clear output.
Cinema:
Video dialogue is reproduced more clearly. Action movies are
reproduced with more powerful sound.
Action:
Action movies are reproduced with more powerful sound.
Drama/Talk:
The dialogue portion of a video is reproduced more clearly.
•When “Non Effect” is selected, MX Plus becomes disabled.
•Sources to be set vary depending on the system set in “Setting the
AUX Input System (AUX Input Setup)” (page39).
10
To adjust another source, press [ ] and repeat
Steps 8 through 9.
•You can listen with Defeat OFF (adjusted setup values) or with
Defeat ON (Initial value) to compare, by following the st eps below.
1 Press and hold the [Rotary Encoder] for 2 seconds or
longer while in the adjustment mode.
2 R otate the [Rotary Encoder] to switch on/off Defeat, and
listen to compare.
3 To exit, select “OFF” and then press [ ].
11
When the setting is complete, press and hold [ ]
for at least 2 seconds.
•If [ ] is pressed during setting, the unit returns to th e previous
item.
•This function is not available when Defeat is set to ON.
•After the setting, it is recommended to store the setting contents on
the unit. For details, refer to “Storing the Preset Values (Preset
Store)” (page36).

Setting the Equalizer Mode (EQ Mode)

You can choose either the Graphic EQ or the Parametric EQ for the
equalizer mode. You can also turn it off. (Initial setting: “OFF”)
1
Press [FUNC.].
2
Rotate the [Rotary encoder] to select “Sound Field
Adj.,” and then press the [Rotary encoder].
3
Rotate the [Rotary encoder] to select “Setup,” and
then press the [Rotary encoder].
4
Rotate the [Rotary encoder] to select “EQ Mode,”
and then press the [Rotary encoder].
5
Select either “G.EQ,” “P.EQ,” or “OFF” by rotating
the [Rotary encoder], and press the [Rotary
encoder].
G.EQ: Graphic EQ is used.
P.EQ: Parametric EQ is used.
OFF: EQ mode is disabled.
6
When the setting is complete, press and hold [ ]
for at least 2 seconds.
•If [ ] is pressed during setting, the unit returns to the previous
item.
•This function is not available when Defeat is set to ON.
•After the setting, it is recommended to store the setting contents on
the unit. For details, refer to “Storing the Preset Values (Preset
Store)” (page36).

Setting the Graphic EQ

The graphic equalizer allows you to modify the sound using 31 bands
each for the front (left and right), rear (left and right) and center
speakers. An additional 10 bands are available for the subwoofer. This
allows you to customize the sound to suit your taste.
•Set “Setting the Equalizer Mode (EQ Mode)” on page 46 to “G.EQ.”
1
Press [FUNC.].
2
Rotate the [Rotary encoder] to select “Sound Field
Adj.,” and then press the [Rotary encoder].
3
Rotate the [Rotary encoder] to select “EQ
Adjustment,” and then press the [Rotary encoder].
The G-EQ screen is displayed.
4
Press and hold [CHANNEL] for at least 2 seconds.
Rotate the [Rotary encoder] to select either “L+R” or
“L or R,” and press the [Rotary encoder].
L or R: Channels Right and Left can be set independently.
L+R: Both Right and Left channels are set at the same
value (The initial setting).
•When you switch from “L or R” to “L+R,” choose which adjustment
of the R and L channels to be applied.
1 Select either “L R” or “R L” by rotating the [Rotary
encoder], and press the [Rotary encoder].
L R: The adjustment of the Left channel is to be applied
to both Right and Left channels.
R L: The adjustment of the Right channel is to be applied
to both Right and Left channels.
01GB00PXAH800.book Page 46 Tuesday, February 8, 2011 9:04 PM