Diamond-VT Technical Overview, RS-232 | ATTO Technology VT-Class

2.0 Diamond-VT Technical Overview

The Diamond-VT uses Aggregated Data Transfer Technology (ADXT) to achieve the high data transfer performance you need. ADXT merges the performance of multiple ATA drives together to achieve sustained, full bandwidth Fibre Channel data transfer rates.

Unlike other storage arrays which use expensive SCSI or Fibre Channel disk drives to achieve performance, the Diamond Series uses lower cost ATA disk drives combined with an intelligent midplane to create a storage array with exceptional price and performance characteristics.

The intelligent midplane contains hardware and software which provide the proprietary ADXT, a switched data management and data movement

technology, to create a higher performance storage solution.

Using this technology, we are able to provide a storage array that delivers faster sustained data transfer rates as well as impressive I/Os per second at a new price point in the storage market.

The Diamond Array is made up of dual SCSI or Fibre Channel host interface cards, the intelligent midplane, a system management card, and 12 independent disk drive sleds containing up to 24 ATA disk drives.

Exhibit 2.0-1 Data pathways and architecture for Fibre Channel operation

	Local Terminal
In band management SNMP / Telnet/ FPT Management	RS-232
In band management SNMP / Telnet/ FPT Management	Ethernet
software

400MB/sec

Duplex

400MB/sec

Duplex

2Gb FC or

Ultra160 SCSI

Host

2Gb FC or

Ultra160

SCSI Host

CPCI bus

Intelligent

Midplane

CPCI bus

Dual Disk
DriveSled	ADXT	™
Dual Disk
DrivueDualSledDisk	organized
DriveDualSledDisk	data
DriveDualSledDisk	streams
DriveDualSledDisk
DriveDualSledDisk
DriveDiualSledDisk
DriveDualSledDisk

DriveDualSledDisk

DriveDualSledDisk

DriveDualSledDisk

DriveSled

I/O Data

System

Management

Card

3

ATTO Technology Inc. Diamond Storage Array Installation and Operation Manual

Image 14

ATTO Technology VT-Class manual Diamond-VT Technical Overview, RS-232, Ethernet, 400MB/sec, Data

Contents

Diamond Storage Array VT-Class Page Page Contents Atto ExpressNAV Browser-based Interface ExpressNAV Pages Maintenance Services Commands Fibre Channel Configuration CommandsSerial Port Configuration Commands Diagnostic Commands Drive Management Commands ECC Resetting Defaults Configuring the Diamond-VTDiagnostics, Upgrade and Maintenance Troubleshooting Virtual Tape Appendix F Product Safety Xiii Appendix D Sample Zoning Command SequencesAppendix E Specifications Xii Appendix G Part numbers Xiv Appendix H Warranty Atto Technology, Inc PrefaceDisclaimer Page Diamond-VT features Diamond Storage Array-VT Product Overview Fibre Channel model Scsi model Ethernet Diamond-VT Technical OverviewRS-232 400MB/sec Adxt Powers ATA to New Levels ATA Interface Engine AIE The interface to each Set up the Ethernet connection Installation InstructionsPhysical setup Connect to Ethernet Connect to Ethernet, on page 5, follow Set up Virtual Tape configurationConfiguration examples RAID Level 10 with Hot Spare sleds Diamond-VT Components Floor model Rack mount model Rack Mount Diamond-VT Physical SetupFloor Model Physical setup Manual configuration Connecting a Fibre Channel ArrayAutoconfiguration Fibre Channel connections Bus speed, MB/sec Bus width Max. bus lengths Max. device Connecting a Scsi ArrayTo connect the Scsi Diamond-VT Bits Scsi connections Atto ExpressNAV Accessing the Diamond-VTCommand Line Interface RS-232 port Snmp Initiator Host Diamond-VT In-band CLI Over Fibre ChannelDetails Initiator/Host Diamond-VT Serial Port Access Serial port access To use Telnet Ethernet Access Telnet and Snmp ProtocolsTo connect to the Ethernet port To use Snmp Traps are generated for the following situations Browser compatibility Atto ExpressNAV Browser-based InterfaceNavigating ExpressNAV Reset button Parameter name Submit button ExpressNAV Pages Logical Units Tape VolumesConfiguration Partitions Ready CLI Interface via ASCII-based CommandsSaveConfiguration command Return type/mode Return format/content Hostname Summary of CLI Commands Command Defaults Example CLI index Zoneaddhost zone1 General Use Commands Ethernet Commands TelnetTimeout SNMPUpdatesTelnetPassword SNMPTraps Fibre Channel Configuration Commands FcScsiBusyStatus FcPortListFcPortName FcWWName SerialPortHandshake Serial Port Configuration CommandsSerialPortBaudRate SerialPortEcho Maintenance Services Commands Diagnostic Commands TapeVolumeInfo PowerAudibleAlarmSledFaultLED RAID5ClearDataStatus Drive Management Commands IdeTransferRate DriveWipeLUNState IdeWriteCache RAIDHaltRebuild RAID5ClearDataRAIDInterleave RAIDManualRebuild RebuildPriority RestoreModePagesTapeVolumeBlockSize TapeWriteProtect ZoneDelete ZoneClearAllZoneCreate ZoneRemoveDevice CLI configure drives RAID Level Configuring the Diamond-VTVirtual Tape Volumes Hot Spare sleds Interleave Enhancing performance Virtual Tape To set up RAID Level 10 with Hot Spare sleds Optional Hot Spare Sled Principles of Zoning Planned configuration is a work-in-processZones Device portion defines the LUNs Type ZoneInfo Factors to considerStatus and Sense Data To remove zones Configuring ZoningTo create a zone To change current zones Errors Zone definition tables The Zone commands Updating firmware via the optional Ethernet card Updating FirmwareUpdating firmware via the RS-232 serial port Cd c\diamond\flash Type put ....ima RS-232 Monitoring Port and CLI One tool to Diagnostics, Upgrade and MaintenancePower On Self Test Post Each time Ethernet Monitoring Port and CLI If the optional 25C 32C 35C 40C Power Supply Monitoring The Diamond-VTSystem Fault LED and Error Codes If a serious Disk Drive Activity and Disk Fault LEDs Each Monitoring, reporting Command Line Interface messages TroubleshootingWindows 2000 special instructions Error Messages Specific situations and suggestions If you cannot read or write to the Diamond-VT If a power supply failsIf you can’t access the Diamond-VT CLI via Ethernet Type FirmwareRestart in CLI Default Resetting DefaultsFactory Default Return to Default settings Command Default Rebuilding RAID Level 5 and 10 Configurations To synchronize mirrored drives manually Hardware Maintenance Hardware maintenance Hot Swap Operating Instructions Disk Drives Blower Assemblies Power SuppliesTo replace a blower assembly SAN technology Appendix a GlossaryFibre Channel technology Scsi protocol Appendix Fibre Channel FeatureAppendix B ATA Disk Technology Appendix C LunInfo for a Jbod setup LunInfo PartitionInfo active 59 TapeVolumeInfo ZoneInfo Viii Simple configuration Appendix D Sample Zoning Command SequencesFirst time configuration after download Symmetric Model ZoneAddPort zone1 ZoneCreate zone2 Asymmetric ModelZoneClearAll ZoneCreate zone1 ZoneAddPort zone2 ZoneCreate zone3 Combined Symmetric/Asymmetric Model Floor Mount Dimensions Appendix E SpecificationsRack Mount Dimensions Environmental and physical EMC specifications Appendix F Product SafetySafety compliances Radio and television interference Appendix G Part numbers Description All models Contact Atto Technology, Inc Appendix H WarrantyManufacturer limited warranty