Atto ExpressNAV Browser-based Interface | ATTO Technology VT-Class

5.0 ATTO ExpressNAV: Browser-based Interface	..............................23
Browser compatibility
Opening an ExpressNAV session
Navigating ExpressNAV
5.1 ExpressNAV Pages	25
Status
Ethernet
SNMP
Serial Port
Fibre Channel
Storage Management
RAID
Clear Data
Logical Units
Partitions
Zoning
Tape Volumes
Tape Drives
Move Medium
Rebuild
Configuration
Advanced
Restart
Help
6.0 CLI: Interface via ASCII-based Commands	27
6.1 Summary of CLI Commands	29
6.2 General Use Commands	32
FirmwareRestart
Help
RestoreConfiguration
SaveConfiguration
SystemSN
VerboseMode
ZoneCommit
6.3 Ethernet Commands	33
EthernetSpeed
Exit
FTPPassword
IPAddress
IPDHCP
IPGateway
IPSubnetMask
SNMPTrapAddress
SNMPTraps
SNMPUpdates
TelnetPassword
TelnetTimeout
TelnetUsername
TelnetUsername

Diamond Storage Array Installation and Operation Manual

Image 5

ATTO Technology VT-Class manual Atto ExpressNAV Browser-based Interface, ExpressNAV Pages

Contents

Diamond Storage Array VT-Class Page Page Contents ExpressNAV Pages Atto ExpressNAV Browser-based Interface Serial Port Configuration Commands Fibre Channel Configuration CommandsMaintenance Services Commands Diagnostic Commands ECC Drive Management Commands Diagnostics, Upgrade and Maintenance Troubleshooting Configuring the Diamond-VTResetting Defaults Virtual Tape Appendix E Specifications Xii Appendix D Sample Zoning Command SequencesAppendix F Product Safety Xiii Appendix G Part numbers Xiv Appendix H Warranty Atto Technology, Inc PrefaceDisclaimer Page Diamond Storage Array-VT Product Overview Diamond-VT features Scsi model Fibre Channel model RS-232 Diamond-VT Technical OverviewEthernet 400MB/sec ATA Interface Engine AIE The interface to each Adxt Powers ATA to New Levels Physical setup Installation InstructionsSet up the Ethernet connection Connect to Ethernet Configuration examples Set up Virtual Tape configurationConnect to Ethernet, on page 5, follow RAID Level 10 with Hot Spare sleds Floor model Diamond-VT Components Rack mount model Rack Mount Diamond-VT Physical SetupFloor Model Physical setup Manual configuration Connecting a Fibre Channel ArrayAutoconfiguration Fibre Channel connections To connect the Scsi Diamond-VT Connecting a Scsi ArrayBus speed, MB/sec Bus width Max. bus lengths Max. device Bits Scsi connections Command Line Interface Accessing the Diamond-VTAtto ExpressNAV RS-232 port Snmp Initiator Host Diamond-VT In-band CLI Over Fibre ChannelDetails Initiator/Host Diamond-VT Serial Port Access Serial port access To connect to the Ethernet port Ethernet Access Telnet and Snmp ProtocolsTo use Telnet To use Snmp Traps are generated for the following situations Browser compatibility Atto ExpressNAV Browser-based InterfaceNavigating ExpressNAV Parameter name Submit button Reset button ExpressNAV Pages Configuration Tape VolumesLogical Units Partitions Ready CLI Interface via ASCII-based CommandsSaveConfiguration command Hostname Return type/mode Return format/content Command Defaults Example Summary of CLI Commands CLI index Zoneaddhost zone1 General Use Commands Ethernet Commands TelnetPassword SNMPUpdatesTelnetTimeout SNMPTraps Fibre Channel Configuration Commands FcPortName FcPortListFcScsiBusyStatus FcWWName SerialPortBaudRate Serial Port Configuration CommandsSerialPortHandshake SerialPortEcho Maintenance Services Commands Diagnostic Commands SledFaultLED PowerAudibleAlarmTapeVolumeInfo RAID5ClearDataStatus Drive Management Commands LUNState DriveWipeIdeTransferRate IdeWriteCache RAIDInterleave RAID5ClearDataRAIDHaltRebuild RAIDManualRebuild TapeVolumeBlockSize RestoreModePagesRebuildPriority TapeWriteProtect ZoneCreate ZoneClearAllZoneDelete ZoneRemoveDevice CLI configure drives Virtual Tape Volumes Configuring the Diamond-VTRAID Level Hot Spare sleds Enhancing performance Interleave Virtual Tape Optional Hot Spare Sled To set up RAID Level 10 with Hot Spare sleds Zones Planned configuration is a work-in-processPrinciples of Zoning Device portion defines the LUNs Type ZoneInfo Factors to considerStatus and Sense Data To create a zone Configuring ZoningTo remove zones To change current zones Zone definition tables The Zone commands Errors Updating firmware via the optional Ethernet card Updating FirmwareUpdating firmware via the RS-232 serial port Type put ....ima Cd c\diamond\flash Power On Self Test Post Each time Diagnostics, Upgrade and MaintenanceRS-232 Monitoring Port and CLI One tool to Ethernet Monitoring Port and CLI If the optional 25C 32C 35C 40C Power Supply Monitoring The Diamond-VTSystem Fault LED and Error Codes If a serious Disk Drive Activity and Disk Fault LEDs Each Monitoring, reporting Windows 2000 special instructions Error Messages TroubleshootingCommand Line Interface messages Specific situations and suggestions If you can’t access the Diamond-VT CLI via Ethernet If a power supply failsIf you cannot read or write to the Diamond-VT Type FirmwareRestart in CLI Factory Default Resetting DefaultsDefault Return to Default settings Command Default Rebuilding RAID Level 5 and 10 Configurations To synchronize mirrored drives manually Hardware Maintenance Hardware maintenance Disk Drives Hot Swap Operating Instructions Blower Assemblies Power SuppliesTo replace a blower assembly Fibre Channel technology Appendix a GlossarySAN technology Scsi protocol Appendix Fibre Channel FeatureAppendix B ATA Disk Technology Appendix C LunInfo for a Jbod setup PartitionInfo active 59 LunInfo ZoneInfo TapeVolumeInfo Viii First time configuration after download Appendix D Sample Zoning Command SequencesSimple configuration Symmetric Model ZoneClearAll ZoneCreate zone1 Asymmetric ModelZoneAddPort zone1 ZoneCreate zone2 ZoneAddPort zone2 ZoneCreate zone3 Combined Symmetric/Asymmetric Model Rack Mount Dimensions Appendix E SpecificationsFloor Mount Dimensions Environmental and physical Safety compliances Appendix F Product SafetyEMC specifications Radio and television interference Description All models Appendix G Part numbers Contact Atto Technology, Inc Appendix H WarrantyManufacturer limited warranty