Front Panel Brightness, Individual Zone Display

50	Display - Tab 8

Note: Display setup for a CT610/310 only.

1. Front Panel Brightness:

Select Off, Dim, Medium or Bright from the list box. When set to OFF the display will turn on briefly when a change occurs and then revert back to off.

2. Individual Zone Display:

For each zone, decide whether the front panel should display changes from that zone as they occur. If all zones are set to ON, the front panel display will change every time any zone receives an IR command.

Note: If Zone A is set to NO, the On Screen Menu will not be accessible.

B & K

S I M P LY B E T T E R !

Page 54

Image 54

B&K CT300, CT600, CT602, CT310, CT610 user manual Front Panel Brightness, Individual Zone Display, Display Tab

Contents

13226 Accessories Included Setup Using a PC and BKcSuite Parts and Accessories GuideInstallation and System Diagrams BKcSuite Setup and Overview Specifications On Screen Main Menu Finesse and Power To Please a Household Introduction / Overview CT Receiver Features and Benefits CK1.2 Keypad Features and Benefits CK1.2 Keypad Features and BenefitsPoint Any Remote Control at the Keypad Status Feedback to Keypads Parts and Accessories Guide CT Receiver Front Panel CT602/600/300 CT Receiver Back Panel S E CK1.2 Front Panel / Back Panel Programming Jack Behind the Faceplate MZ-128 Remote Control DB-9 to RJ-45 Adapter P/N13290 CT-1 System Integrator P/NRJ-45 to 5 position Phoenix Adapter P/N BK Toolbox CD-ROM P/N Installation and System Diagrams Installation and System Diagrams Basic System Hookup Installation Considerations Placement and VentilationDefault Operation Connection Strategy Speaker Connections for CT Receiver AC Power and Line FuseAccommodate up to 12-gauge wire Speaker Connections CT310 Example CT Receiver Six Zone Speaker Connections CT Receiver Speaker Connections Keypad Connections Example connection of a CK1.2 Keypad CK1.2 Keypad Connections Common GroundCT Receiver cannot receive RS-232 via this terminal Adding Additional Keypads in the Same Zone Left Control Card Shared Source Connections CT Receiver Connection IR Flasher Emitter Output Buffered OutputsIR Emitter Outputs Zone Line Outputs Zone Line Outputs Changing Line Level Outputs From Fixed to Variable Dedicated Source Inputs LocalFixed Output / Variable Output Local IR Source Control Local Source IR Control Common Control Triggers CT Receiver Common Control Connection and TriggerCommon Control Triggers AM Loop Antenna Factory ResetRF Remote FM Antenna System Expansion System Expansion Swap Cable Between Two CT Receivers Connecting Two CT ReceiversCoupling Two CT Receivers Maximum 12 Stereo Zones Should not be connected between RJ- 45 jacks Adding a 7th Zone Adding a 7th Zone Using The AVR507/505/50 Second ZoneSeventh Zone Connection Diagram No identical Sources CAT5 T568B Swap Cable Swap Cable ConstructionCT-1 IR Routing System Integrator RS-232 Swap Cable Basic Expanded System Using a CT-1 CT610 #3 CT610 #2 Source Control Using a CT-1 CT-1 Power Connection 12VDCCT-1 Expansion Adding a Home Theater RS-232 Connection Using a Swap Cable to Control a Theater Setup Using a PC and BKcSuite Setup Using a PC and BKcSuite Computer Connection Connection to a PCCT Receiver Connection USB to Serial Adapter BKcSuite Setup and Overview BKcSuite Setup and Overview BKcSuite Task Bar Explained BKcSuite Task Bar Explained Basic Setup Menu Basic Setup Menu Advanced Full Setup Menu Advanced Setup Menu Hardware Zone Settings Tab Left and Right Level Calibration Fixed or Variable Levels for Stereo ZonesMaximum Level Limits the Output whether Fixed or Variable Fixed or Variable Levels for Mono Zones Splitting a Zone To Mono Sub-Zoning Code-Set Description and Overview Code-Set Description and Overview Groups / Code Sets / Zones Tab M P LY B E T T E R Shared Source Input Names Input Settings To Compensate LevelsInput Settings Tab Dedicated Source Input Names Power On Titles Tab Power-On Preferences Tab Select Power On SettingPower On Preference Select Code Set Input Configuration Tab Input ModeSelection Mode Release Time Action Activated By/ Event Tab Level Event Front Panel Brightness Individual Zone DisplayDisplay Tab Headphone Zone ControlZone Control Out 12V Control Tab Flasher Outputs Zone Rear Data In SettingIR Flasher Settings Tab Front Panel IR to Flasher Outputs Front Panel IR Setup Menu VisibleFront Panel Buttons Memory Locked Baud Rate RS-232 Port EnableRS-232 Echo Enabled RS-232 Receive & Transmit ID Convert IR to BKC-DIP Messages V2.0 EnabledRS-232 Feedback Selection Continuous Reply Transmit BKC-DIP to Zones Preset Operation Tab Recall Volume In PresetFavorite Preset Recall Auto Naming Keypad Feedback Tab Preset Editor Features and Benefits Opening the Preset EditorPreset Editor Preset Editor Window Editing Presets RS-232 Serial Macro Editor RS-232 Serial Macro Editor CK1.2 Keypad CK1.2 Keypad Setup Using the On Screen Display Setup Using the On Screen Display On Screen Menu Tree Diagram CT Receiver On Screen Display Menu Structure OSD Using a Remote Control Using The Remote Control and On-Screen MenusOn Screen Menu Operation with the MZ-128 CT610 / CT310 CT602 / CT300 No front panel operationFront Panel Buttons Main Menu On Screen Main Menu Zone Favorite Presets Menu Zone Operation Naming an Input Audio/Video System SetupInputs Sub-Menu Main Menu Sub-menu’s Zone Menu when set to Mono Menu Items for a Dedicated InputAudio / Video Submenu Zone Power On Settings Page/Event Setup Zone Code-Sets/Names and Group Titles Control Menu SetupDisplay Setup Control System Menu Zone Code-Sets/Groups and Group Titles Code Set IR Routing for Identical Components Common Control I/OFlasher Out Flasher Output IR to Flasher Out Preset Volume Presets SetupPower On Titles Preset Names Control System Setup Security OptionsRS-232 Options Memory Backup Setup RS-232 Slave Control Main Menu Setup System Status # of Volume Controls Zone Planning Worksheets CT Receiver Input Planning Cable Calculation Source Distance for Home Run TotalInput Planning Worksheet CT Receiver Preferences and Presets Power On Preferences and PresetsProject Manager Date Troubleshooting Guide For BKcSuite Troubleshooting Guide for CT ReceiversProblem Possible Solution Limited Warranty Returning Equipment Specifications CT610/602 CT600 CT310 CT300

B&K CT300, CT600, CT602, CT310, CT610 Front Panel Brightness, Individual Zone Display, Display Tab

Models: CT300 CT610 CT310 CT602 CT600

Display - Tab 8

1. Front Panel Brightness:

2. Individual Zone Display:

S I M P LY B E T T E R !