Baldor MN1940 3.1 Introduction

www.baldormotion.com

BasicInstallation 3-1MN1940

3.1 Introduction

Youshould read all the sections in Basic Installation.

Itis important thatthe corr ect steps are followed when installing the DSM.

Thiss ection describes the mechanical installation of the DSM.

3.1.1 Location req uirements

Ensure you have read and understood the warnings and cautions in sec tion 1.

Thesafe oper ation of this equipment depends upon its use in the appropriate environment.

Thefollowing points mustbe c onsidered:

HTheDSM is designedto be mount ed indoors, permanently fixed and located.

HTheDSM mus t be secured by the holes in the faceplate.

Because the DSM consists of two core components , a drive and a motor, attention must be

paidto the thermal s pecifications of both the motor and the electronics. The following

maximumtemper atures apply to the DSM:

HTheDSM heat s ink temperature must not exceed 85 °C (185 °F).

HTheDSM motor t emperature must not exceed 100 °C (212 °F).

3Basic Installation 3

Contents

Main Page Contents 3 Basic Installation 3-1.................................... 4 Input / Output 4-1...................................... 5 Operation 5-1.......................................... 6 Troubleshooting 6-1.................................... 7 Specifications 7-1...................................... GeneralInformation 1-1MN1940 1General Information 1 1-2 GeneralInformation MN1940 Safety Notice Precautions Introduction 2-1MN1940 2Introduction 2 2.1 DSM S-Series integrated motorand d river 2-2 Introduction MN1940 2.1.1 Option availability Introduction 2-3MN1940 2.2 Receiving and inspection 2.2.1 Identifying thecatalog number 2-4 Introduction MN1940 2.3 Units and abbreviations BasicInstallation 3-1MN1940 3Basic Installation 3 3.1 Introduction 3.1.1 Location req uirements 3-2 BasicInstallation MN1940 3.1.2 Mountingthe DSM BasicInstallation 3-3MN1940 Figure2 - Screw thr eadlimitation - DSMS17 3-4 BasicInstallation MN1940 BasicInstallation 3-5MN1940 3-6 BasicInstallation MN1940 3.1.3 Other requirements for installation Input/ Output 4-1MN1940 4.1 Introduction 4.1.1 Basic connectio ns 4Input / Output 4 4-2 Input/ Output MN1940 4.2 Motor power input Input/ Output 4-3MN1940 4.2.1 Wire sizes 4-4 Input/ Output MN1940 4.3 Logic inputs 4.3.1 Logicinput descriptions Input/ Output 4-5MN1940 4.3.2 Input timing 4-6 Input/ Output MN1940 4.3.3 Sinking/ sourcing input configuration www.baldormotion.com Input/ Output 4-7MN1940 4-8 Input/ Output MN1940 4.4 SPI interface 4.4.1 SPI connector Input/ Output 4-9MN1940 4.4.2 SPI signal descriptions 4-10 Input/ Output MN1940 4.5 Connection summary - minimum system wiring Operation 5-1MN1940 5Operation 5 5.1 Introduction 5.1.1 Connectin g the DSM to the PC 5.1.2 Installing the USB driver 5.1.3 Installing the virtualCOM port driver 5-2 Operation MN1940 5.1.4 Determining the virtualCOM port number 5.1.5 Installing Baldor SPI Interface Operation 5-3MN1940 5.1.6 Startingthe controller and DSM 5-4 Operation MN1940 5.2 Baldor SPI Interface 5.2.1 Starting Baldor SPI In terface 5.2.2 Configurat ion parameters Operation 5-5MN1940 5-6 Operation MN1940 Troubleshooting 6-1MN1940 6Troubleshooting 6 6.1 Introduction 6.1.1 Problemdiagnosis 6.1.2 Furthersupport 6.1.3 Communication probl ems 6-2 Troubleshooting MN1940 6.1.4 Motor controlproblems Specifications 7-1MN1940 7.1 Introduction 7.1.1 Input power 7Specifications 7 7-2 Specifications MN1940 7.1.2 Motor speed & torque - DSMS17 Specifications 7-3MN1940 7-4 Specifications MN1940 7.1.3 Motor speed & torque - DSMS23 Specifications 7-5MN1940 7.1.3.3 DSMS23x-3B... www.baldormotion.com 7-6 Specifications MN1940 7.1.4 Motor speed & torque - DSMS34 (2100) (1800) (1500) (1200) Specifications 7-7MN1940 7.1.4.2 DSMS34x-2B... 7-8 Specifications MN1940 7.1.4.3 DSMS34x-3B... Specifications 7-9MN1940 7.1.5 Digitalinputs Page Index MN1940 A Index B C D M O P R S Comments CommentsMN1940