Mounting the 8000i 12 inch Display Processor | Belkin 8000I specs

7Mounting the 8000i 12 inch Display Processor

Choosing the best mounting location

Choose the mounting locations carefully before you drill or cut. The 8000i Display should be mounted so that the operator can easily use the controls and clearly see the display screen. Be sure to leave a direct path for all of the cables. The display screen is high-contrast and anti-reflective, and is viewable in direct sunlight. For best results, install the 8000i 12" Display out of direct sunlight. The chosen location should have minimal glare from windows or bright objects.

NOTE: The LCD itself is the front panel. There is no plastic lens in front of the LCD. It has a special bonded anti-reflective and scratchproof film on the LCD front to assure no fogging and best contrast. DO NOT hit the lens with sharp or heavy objects because expensive LCD damage may occur.

The system is designed to allow full operation of the unit from a Windows compatible mouse. If the mounting location means that the unit is not easily within reach of the user in the helm chair you may wish to also install a 8000i Remote Keypad or third party USB Trackball to the helm chair.

Leave sufficient clearance space behind the 8000i 12" Display Processor to connect all relevant cables.

Good ventilation is required behind the mounting panel. Poor ventilation may cause the 8000i 12" Display Processor to overheat, which, in turn, will cause the unit not to run at optimum performance. For overall width and height requirements, please see the diagram below.

The system requires the use of the touch screen or external mouse. If the unit is to be mounted outdoors and may experience conditions that would require the touch screen to be disabled (e.g. Hail, Snow) we recommend that a water proof pointing device (e.g. 8000i Remote Keypad or water proof USB mouse) is connected to the system.

Northstar 8000i System - 12" Display Processor Installation Manual

33

Image 33

Belkin 8000I installation manual Mounting the 8000i 12 inch Display Processor, Choosing the best mounting location

Contents

Northstar Important Safety Information PrefacePlease read carefully before use Ft 0.5 m Disclaimer Warranty Contents Example System Layouts Maintenance Check the 12 inch Display Processor parts Introducing the Northstar 8000i System Chart License Key NS004820 Page PPI Find your way around the 12 inch Display Processor RGB Network Master Unit Installation Sequence Summary Guidelines 8000i System Installation Description Northstar 8000i 12 inch Display ProcessorPlace in 8000i System Optional Parts Northstar 8000i Black Box Processor Power requirementsLocation Guide Mounting Northstar 8000i 15 inch Monitor Other parts required Power requirements Voltage Fuse Draw Northstar 8000i Network RadarFunctions Northstar 8000i 8 Port Network Linker Northstar 8000i 4 Port USB Hub Functionality Northstar 8000i 1 kW Network Sounder Northstar 8000i DVD-CD Player Northstar 8000i Remote Keypad Northstar 8000i Video Interface Northstar 8000i C-MAP Chart License Key Northstar GPS Antenna NS004743 Autopilot Other Components Heading Sensor AudioMounting and Calibration GLL NMEA-0183 Data GSA Mass Storage Devices Network Camera Human Interface DevicesDescription Place in 8000i System Other Functions Location Guide Choosing the best mounting location Mounting the 8000i 12 inch Display Processor Viewing Angle Page Page Wiring Guidelines Power Northstar 8000i Black Box 8000i System Power requirements GPS Port Utility Port External Wake Up and Remote Power On Connect this to the Light Green wire on Page Nmea Multiplexer Noland NM42 Nmea Wiring Connect the following External AlarmPage USB Auxiliary port Network RGB portPage Field Terminated Network Cable Brown White/Brown Blue White/Green White/Blue Terminating a Northstar 8000i RJ45 Field Kit Before crimp After crimp Example System Layouts 8000i Chart Plotter 8000i Plotter Sounder NS004743 Northstar GPS Antenna Entertainment Northstar 8000i Processor Full System Northstar Black Box Processor NS004730 Adjust the brightness on a 12 inch Display Processor Northstar 8000i Initial SetupTo adjust the backlight brightness Turn on the 12 inch Display Processor To set the master Set the network master unit Install Charts interface Install the chart dataTo install chart collections To install all collections Turn off the 12 inch Display Processor To select the time format Set the system preferencesTo select your time zone To turn the beeps on or off To turn the backlight on or off To change the transducer depthChange the transducer depth Turn the keypad backlight on or off Specify your vessel statistics To show or hide the top control barTo specify your vessel statistics Set the location of the media library To select Nmea Output sentences Set Nmea Output Calibrate the touch screen Set Nmea Baud RateTo calibrate the touch screen Set the device processor name Set the units Set the screen resolution To select the volume units for liquids To select the large scale distance unitsTo select the small scale distance units To set up the radar before using it To select the temperature unitsSelect the temperature units Set up the radar before using it for the first time To change the radar startup mode Change the radar startup modeChange the radar range offset trigger delay To change the radar bearing alignment To change the radar range offsetTo change the parking angle Change the radar bearing alignment To change the water temperature averaging time To change the offset for the water temperatureSounder To change the speed offset To create an instrument panel InstrumentsChange the sounders speed filter Create an instrument panel To resize an instrument To add a new instrumentTo rename an instrument panel Resize an instrument Delete an instrument panel To delete an instrument panel Technical support, service and repairs Maintenance Restore settings and information RestoreRestore processor software To restore the system processor Upgrading the 8000i system There two types of upgrade for a 8000i processor Install a system image upgrade Install a software patch to multi processor systemSystem image upgrade Software patch multi-processor system Master Thirty minutes System will then restart automatically Display Specifications United States Europe Northstar