MIC Series 500 CameraNavigating the Menus en 33

Menu Item

Description

Options

Default

 

 

 

 

CLEAR SOFT

Clears any Soft stops that have been applied.

RIGHT TO

N/A

STOPS

 

CLEAR

 

 

 

 

 

MANUAL

Gives the user 10 seconds of manual control of the camera to allow the operator to move the

CONTROL

camera to the desired position before the menu returns to its previous state.

 

 

 

 

 

WASH WIPE

Sets the wash position by pointing the camera at the washer nozzle

RIGHT TO SET

current

POSITION

and pressing right to set.

POS

camera

 

 

 

position

 

 

 

 

SET ZERO

Sets the zero degree (North) position when using the compass

RIGHT TO SET

N/A

POS

direction captions. For example, point the camera North, Set Zero Pos,

POS

 

 

resulting in the caption correctly displaying the compass heading.

 

 

 

 

 

 

UPPER LEFT

Soft Stops enable the user to set up an imaginary box within which the

RIGHT TO SET

Cleared

AND LOWER

camera can move. There is only one zone available which is defined by

POS

 

RIGHT SOFT

first setting the Top Left and then the Bottom Right of the zone. Once

 

 

STOP

activated the MIC cannot be moved beyond the area set.

 

 

 

 

 

 

LEFT AND

These 2 settings define the limits within which the camera will pan at

RIGHT TO SET

Cleared

RIGHT AUTO

the “Auto Pan Speed” when the “Auto Pan” feature is activated.

POS

 

PAN LIMITS

 

 

 

 

 

 

 

MAP AUX TO

This option opens a submenu that allows certain features of the

WIPER,

N/A

PRESET

camera which would normally be controlled through Aux commands to

WASHER,

 

 

be mapped to Go To Preset commands. The features available for this

DIGITAL

 

 

are Wiper, Washer, Digital Zoom, Auto Iris, Auto Focus, and Auto Pan.

ZOOM,

 

 

For each function there are 3 options: Control, On Preset, and Off

AUTO IRIS,

 

 

Preset. The control field denotes if the function is activated by the

AUTO FOCUS,

 

 

normal aux command or through a preset. The other 2 options set the

AUTO PAN

 

 

preset number to activate or deactivate each function. This provides

 

 

 

the ability to run all of the camera’s standard auxiliaries from a wider

 

 

 

range of control systems with varying direct aux support.

 

 

 

Note: If the control field of any of the functions is set to Go To Preset,

 

 

 

then the feature will not work using a standard button from a normal

 

 

 

controller. Similarly, if mapped to an Aux command, the preset values

 

 

 

indicated will have no effect.

 

 

 

 

 

 

FIND END

Rotates the tilt axis first down then up to its mechanical limit stops. It

RIGHT TO

N/A

STOPS

then stores a “soft” limit a few units back from these for normal use.

START

 

 

Note: manual control is not available during this process.

 

 

 

 

 

 

RESET TO

Resets to the default settings for all OSD menus.

CONFIRM

N/A

DEFAULTS

 

RESET, NO

 

 

 

 

 

5.7.1

Factory Defaults

 

Restores the camera unit to the Factory Default settings. See Section 5.14.1 Factory Defaults,

 

page 49.

5.7.2

Re-map Pelco Aux (Pelco D and P Protocols only)

 

The Pelco protocols (D and P) support 8 different auxiliaries, but do not define what function

each should perform. This feature enables the 8 available auxiliaries to be set to any of the 8 available functions (Auto Focus, Digital Zoom, Auto Iris, Wiper, Washer, OSD and Backlight). By default, the auxiliaries are mapped as follows:

Bosch Security Systems, Inc.

User’s Manual

F.01U.173.601 2.0 2010.11

Page 33
Image 33
Bosch Appliances 500 user manual Factory Defaults, Re-map Pelco Aux Pelco D and P Protocols only