DIP switches inside the control box | Brother BAS-326F-0 specs

10. DIP SWITCH

10-2. DIP switches inside the control box

DANGER

Wait at least 5 minutes after turning off the power switch and disconnecting the power cord from the wall outlet before opening the face plate of the control box. Touching areas where high voltages are present can result in severe injury.

Main circuit board

1280S

DIP Switch C

SW No.

When ON

C-1	-

C-2	-

C-3	-

C-4	Controlled sewing area becomes 1200 mm X 400 mm

CFor pneumatic type, set to ON when the connection has been changed so that the work clamp

-5remains raised when the power is turned off.

C-6	When using an air-driven intermittent work clamp

C-7	-

C-8	-

56

BAS-311F-0, 311F-L, 326F-0

Image 63

Brother BAS-326F-0, BAS-311F-L, BAS-311F-0 instruction manual DIP switches inside the control box, DIP Switch C

Contents

BAS-326F-0 Safety indications and their meanings Safety Instructions Environmental requirements Installation Cleaning SewingMaintenace and inspection Direction of operation Frame side cover Contents Changing Special Functions Name of Major Parts BAS-311F-L *3 a BAS-326F-0 *4 a Specifications Installation Positioning Table processing diagram Installing the control box Installing the oil pan Installing the rubber cushions Installing the switching plate Installing the cushions Installing the machine head Tilting the sewing machine head 1170S Connecting the cords Installing the operation panel Connecting the ground wire BAS-311F-0 Solenoid type only ORG Installing the belt cover Installing the foot switchInstalling the spool stand Installing the eye guard Installing the programmer option Installing the X feed base cover BAS-311F-L, 326F-0 Installing the feed base cover supports BAS-311F-L, 326F-0 Connecting the tubes pneumatic type only When installing to a beam When installing to the underside of the work table Lubrication Lubrication pointsBAS-326F-0 Installing the needle Correct OperationSelecting the needle and thread Threading the upper thread Winding the lower thread Sewing conditions and thread tension Replacing the bobbin case and threading the thread Lower thread tension Explanation of panel Using the Operation Panel 110 Compatible types of floppy disk Using the floppy disk How to use the cleaning disk Setting the floppy disk To Read a pattern to memory Using the program R/W Read/Write switchIf an error message is displayed Clearing the error Resuming operation from a stopping poing Using the Test switch Checking the sewing pattern Continuing sewing from a stopping point Using the emergency stop switch Changing the X-SCALE and Y-SCALE settings Adjusting the sewing Speed control Using the bobbin thread counter Using production counter Using single split mode Shifting a stitch pattern Sewing Before starting sewingSewing operation 1230S Draining the oil Cleaning and InspectionCleaning the rotary hook Lubrication Checking the needle Cleaning the control box air inlet portCleaning the air holes of belt cover and frame side cover Cleaning the eye guard Standard Adjustments Adjusting the needle bar heightAdjusting the needle bar lift amount Adjusting the needle clearance Adjusting the driver needle guardAdjusting the shuttle race thread guide Adjusting the movable knife Abcd Replacing the movable and fixed knives Adjusting the presser foot Standard presser foot lift is 3 mm max mm Adjusting presser foot lift to 3 5mmAdjusting presser foot lift to 5 8 mm Changing the presser foot lift For vertical wiper standard Adjusting the wiper BAS-311F-0 Solenoid type Adjusting the two-step work clamp lift amount BAS-326F-0 Adjusting the needle up stop position Checking the input sensor and DIP switch input Checking the input voltage Clearing all memory settings Panel DIP switch functions DIP Switch BAS-311F-L only Dipswitch DIP Switch C DIP switches inside the control box Dipswitch Changing Special Functions and Using the Memory Switches If memo-0E is ON, the work clamp opens and closes twice Switch No When on Memo-10 Main circuit board instead of the voltage Switch No Possible Units Error Codes Can not backup data. Control PCB Turn off power and check connector P20 Gauge Parts List According to Subclasses Bobbin case assy S59221-001 LC Troubleshooting Incorrect needle and rotary hook timing Adjust the needle bar lift Amount Adjust the position Head position switch cord connection WP stitch device Automatic bobbin changer Options Play prevention work clamp 15-1, Naeshiro-cho, Mizuho-ku, Nagoya 467-8561, Japan. Phone