Brother BAS-326F-0, BAS-311F-L, BAS-311F-0 instruction manual Switch No Possible Units

11. CHANGING SPECIAL FUNCTION AND USING THE MEMORY SWITCHES

Memory switches (30 - 3F)

Turn the dial while pressing the STEP BACK switch to change the values.

Switch No.	Possible	Units	Initial			Explanation
	setting range		Value
memo-30	1 - 999	X 10ms	10	Time until feed mechanism starts moving after work clamp has
				lifted.
memo-31	1 - 4	-	1	Changes the feed speed.
				1	(Fast)	4 (Slow)
				Changes the possible sewing speed for a given stitch length.
				1	(Fast)	7 (Slow)
memo-32	1 - 7	-	3	1	(2,700/3 mm), 2 (2,600/3 mm), 3 (2,500/3 mm),
				4	(2,300/3 mm), 5 (2,000/3 mm), 6 (1,800/3 mm), 7 (1,200/3 mm)
				Settings 1 and 2 are outside the warranty specification at the
				time of shipment from the factory.)
memo-33	1 - 10	X 7.5	5	Changes the feed timing.
				1	(Fast)	5 (standard)	10 (Slow)
memo-34	1 - 5	stitch	1	Number of low-speed stitches sewn at 400 rpm at sewing start.
				Solenoid ON time changes (BAS-311F solenoid specifications
memo-35	10 - 60	ms	40	only).		60 (High work clamp capacity)
				10 (Quiet)
memo-36	1 - 3	-	1	The solenoid ON time when the presser foot is raised changes.
				(Standard) 1		3 (Upper limit)
				Automatically corrects the gear speed when reading 2DD disks.
				0	: No automatic correction
memo-37	0 - 3	-	0	1	: Read as BAS-311A data
				2	: Read as BAS-326A data
				3	: Read as BAS-341A, 342A data
				ex. Read BAS-326A data by BAS-311F / Set memo-37=2
				Changes the length of time from inserting the cassette until
memo-38	1 - 20	X 100 ms	1	automatic
				starting when the eject device is being used and automatic starting has
				been set (memo-03 and DIP switch A-7 are also both ON).
				Changes the reference point for enlargement and reduction using
				the operation panel.
				0	: Sensor home position
				1	: Center of work clamp
				2	: Upper-left corner of work clamp
				3	: Lower-left corner of work clamp
memo-39	0 - 11	-	0	4 : Upper-right corner of work clamp
				5	: Lower-right corner of work clamp
				6	: Sewing start point, 7 : Sewing end point
				8	: Upper-left corner of sewing pattern
				9	: Lower-left corner of sewing pattern
				10 : Upper-right corner of sewing pattern
				11 : Lower-right corner of sewing pattern
				Changes the speed limit for the given sewing pitch when the
				maximum speed remains constant.
				1	: Speed limit is increased for the given sewing pitch and the
				2	sewing speed for that pitch is increased.
					: Standard
memo-3A	1 - 3	-	2	3	: Speed limit is decreased for the given sewing pitch and the
					sewing speed for that pitch is decreased.
				Note
				If sewing slippage occurs in places where a large sewing pitch is
				used, reduce the setting to 3.
				Furthermore, sewing slippage may occur in some cases if setting
				1 is used.
memo-3b	-	-	0	-
memo-3c	-	-	0	-
memo-3d	-	-	0	-
memo-3E	-	-	0	-
memo-3F	-	-	0

62

BAS-311F-0, 311F-L, 326F-0