Installing the eye guard | Brother BAS-311F-L, BAS-326F-0 specification

3. INSTALLATION

3-15. Installing the eye guard

CAUTION

Attach all safety devices before using the sewing machine.

If the machine is used without these devices attached, injury may result.

Install the eye guard assy (1) to the face plate with the two screws (2).

(1)

(2)

1180S

BAS-311F-0, 311F-L, 326F-0

15

Image 22

Brother BAS-311F-L, BAS-326F-0, BAS-311F-0 instruction manual Installing the eye guard

Contents

BAS-326F-0 Safety Instructions Safety indications and their meanings Installation Environmental requirements Sewing CleaningMaintenace and inspection Direction of operation Frame side cover Contents Changing Special Functions Name of Major Parts Specifications BAS-311F-L *3 a BAS-326F-0 *4 a Installation Table processing diagram Positioning Installing the control box Installing the rubber cushions Installing the oil pan Installing the cushions Installing the switching plate Installing the machine head Tilting the sewing machine head 1170S Connecting the ground wire Connecting the cords Installing the operation panel BAS-311F-0 Solenoid type only ORG Installing the foot switch Installing the belt coverInstalling the spool stand Installing the eye guard Installing the programmer option Installing the feed base cover supports BAS-311F-L, 326F-0 Installing the X feed base cover BAS-311F-L, 326F-0 Connecting the tubes pneumatic type only When installing to the underside of the work table When installing to a beam Lubrication points LubricationBAS-326F-0 Correct Operation Installing the needleSelecting the needle and thread Threading the upper thread Winding the lower thread Replacing the bobbin case and threading the thread Sewing conditions and thread tension Lower thread tension Using the Operation Panel Explanation of panel 110 Using the floppy disk Compatible types of floppy disk Setting the floppy disk How to use the cleaning disk Clearing the error Using the program R/W Read/Write switchIf an error message is displayed To Read a pattern to memory Using the Test switch Checking the sewing pattern Resuming operation from a stopping poing Using the emergency stop switch Continuing sewing from a stopping point Adjusting the sewing Speed control Changing the X-SCALE and Y-SCALE settings Using the bobbin thread counter Using production counter Using single split mode Shifting a stitch pattern Before starting sewing SewingSewing operation 1230S Lubrication Cleaning and InspectionCleaning the rotary hook Draining the oil Cleaning the eye guard Cleaning the control box air inlet portCleaning the air holes of belt cover and frame side cover Checking the needle Adjusting the needle bar height Standard AdjustmentsAdjusting the needle bar lift amount Adjusting the driver needle guard Adjusting the needle clearanceAdjusting the shuttle race thread guide Adjusting the movable knife Replacing the movable and fixed knives Abcd Adjusting the presser foot Changing the presser foot lift Adjusting presser foot lift to 3 5mmAdjusting presser foot lift to 5 8 mm Standard presser foot lift is 3 mm max mm Adjusting the wiper For vertical wiper standard Adjusting the two-step work clamp lift amount BAS-311F-0 Solenoid type BAS-326F-0 Adjusting the needle up stop position Checking the input sensor and DIP switch input Clearing all memory settings Checking the input voltage DIP Switch Panel DIP switch functions Dipswitch BAS-311F-L only DIP switches inside the control box DIP Switch C Dipswitch Changing Special Functions and Using the Memory Switches If memo-0E is ON, the work clamp opens and closes twice Switch No When on Memo-10 Main circuit board instead of the voltage Switch No Possible Units Error Codes Can not backup data. Control PCB Turn off power and check connector P20 Gauge Parts List According to Subclasses Bobbin case assy S59221-001 LC Troubleshooting Incorrect needle and rotary hook timing Adjust the needle bar lift Amount Adjust the position Head position switch cord connection Options WP stitch device Automatic bobbin changer Play prevention work clamp 15-1, Naeshiro-cho, Mizuho-ku, Nagoya 467-8561, Japan. Phone