Launching the Ring Map, From the icon | Cabletron Systems TRMMIM

Ring Map

Launching the Ring Map

To launch the Ring Map application

from the icon:

1.Click on the appropriate TRMMIM icon to display the icon menu.

2.Drag down to Ring Map and release.

from the Hub View:

1.Click on to display the Device menu.

2.Drag down to Ring Map and release.

from the command line (stand-alone mode):

1.From the appropriate directory, type the following at the command line: spmarun e5map <IP Address> <community name>

NOTES

The spmarun script invoked ﬁrst in the above command temporarily sets the environment variables SPMA needs to operate; be sure to use this command any time you launch an application from the command line. This script is automatically invoked when you launch an application from the icon menu or from within the Hub View.

If you wish to conﬁgure a station while in the Ring Map window, be sure to use a community name with at least Read/Write access. If you only wish to view the ring map, a community name with Read access will be sufﬁcient.

If there is a hostname mapped to your TRMMIM’s IP address, you can use <hostname> in place of <IP address> to launch this application. Please note, however, that the hostname is not the same as the device name which can be assigned via Local Management and/or SPMA; you cannot use the device name in place of the IP address

The Ring Selection window, Figure 3-1, will appear.

3-2	Launching the Ring Map

Image 52

Contents

Trmmim Page Virus Disclaimer Restricted Rights Notice Applicable to licenses to the United States Government only Contents Chapter Ring Map Chapter Alarm ConﬁgurationChapter Statistics Chapter Ring Security Conﬁguration Appendix a Trmmim MIB Structure Contents Using the Trmmim User’s Guide Trmmim What’s not in the Trmmim Guide Introduction to Spma for the Trmmim Conventions Screen Displays Introduction to Spma for the Trmmim Using the Mouse Button Getting Help FTP Trmmim Firmware Introduction to Spma for the Trmmim Trmmim Firmware Using the Trmmim Hub View Using the Hub View Using the Trmmim Hub View Navigating Through the Hub View Hub View Front Panel Trmmim Hub View Uptime Time and DateDevice Name Device Location Using the Trmmim Hub View Using the Mouse in a Hub View Module Module Index FNB Bypass State Hub View Port Color Codes Port Display Form Errors FramesTotal Bytes Port Type FNB Display Monitoring Hub Performance Using the Trmmim Hub View Checking Device Status and Updating Front Panel Info Name and Location Checking Module Status ContactDate and Time Total Rings Speed Fault Speed Fault LocationModule Name Module Admin State Checking Port StatusPort Name Module/Port Link State Time Checking Station StatusInsertion Trap Vendor Station NameUpstream Neighbor/Downstream Neighbor Physical Location PriorityPort Mapping Reverse MACs Checking Ring Port Status Conﬁguring Station Name, Location, or Priority Fault State Time Media FaultClass Media Type Checking Statistics Bytes LineBurst Abort Managing the Hub at the Device Level Managing the HubFind MAC Address Setting the Polling Intervals 12. The Find MAC Address Window 13. Trmmim Polling Intervals Contact Status Device General Status Device ConﬁgurationPort Operational State Statistics Managing the Hub at the Module Level Controlling Token Ring FNB Multiplexer Connections INS Board Left ConnectRight Connect Bypass Controlling Token Ring Speed Clearing the Module FNB Conﬁguration Window Selections Controlling Token Ring MIM Management Mode Enabling All Ports on Token Ring ModulesAuto AUT Management MGT Converting a Station Port to a Ring-out Port Managing the Hub at the Port LevelEnabling and Disabling Station and Ring Ports Removing a Station from the Ring Ring Map From the command line stand-alone mode Launching the Ring MapFrom the icon From the Hub View Selecting a Ring to Map Ring Name Ring Map Speed StationsName Utilization Viewing Station-speciﬁc Information Quick Info Popup Window Board and Port Drop Setting a Station Name Performance and Errors Setting a Station Drop Viewing Management Station Conﬁguration Commands Error Status Open Status Error Active Monitor Error Report Timer Setting the Statistics Calculation ModeViewing Ring-level Information Viewing the Error Table Set Calculation Mode Window Error Table Window Total Errors Isolating Errors Non-Isolating Errors Changing the Station Labels Viewing Device Information Setting the Map Poll Interval Device Information Window Viewing Beacon History Active Monitor ChangesRing Purges Beacon Events Longest Beacon Last Beacon TypeLast Beacon Beacon Conﬁguration 12. The Beacon Conﬁguration Window Using the Find Options Searching by Station Name, MAC Address, Board/Port, or Drop 13. Sample Find Windows Finding the Active Monitor on the Network Finding the Management Station on the Network Frames or Errors measured/Δ Time in seconds Accessing Other Spma Applications 14. Sample Find Highest and Lowest Windows Alarm Conﬁguration Spmarun e5alarms IP address community name Setting and Viewing Ring Alarms Alarm Conﬁguration Setting and Viewing Station Alarms Setting a Ring Level Alarm Alarm Conﬁguration Alarm Conﬁguration Alarm Conﬁguration Setting a Station Level Alarm Alarm Conﬁguration Setting and Viewing Station Alarms Using Statistics Statistics Viewing the Ring Station List Spmarun e5stats IP Address community name Module and Port Stn NameUpstream Addr Downstream Addr Monitoring Ring and Station Statistics Using the Reverse MAC ButtonRefreshing the Station List Creating a Pie Chart Creating a Graph or Meter Click mouse button 1 on Ring and Station Variables GeneralProtocols KBytes Isolating Errors Line ErrorsBurst Error AC Error Abort Error Non-Isolating ErrorsInternal Error Token Errors Frequency Errors Statistics Ring and Station Variables Ring Security Conﬁguration About Ring Security Launching the Security Conﬁguration Window Ring Security Conﬁguration Security Conﬁguration Ring Selection window, -1, will appear Allowed Station List Allowed CountDisallowed Station List Disallowed Count Disable Security Security Mode OptionsEnable Security Allowed/Disallowed List Conﬁguration Buttons Conﬁguring Security Building the Allowed List Automatically Deleting Stations from the Allowed or Disallowed Lists Station Addition Window Clearing All Entries in the Allowed or Disallowed List Clear List Window Changing the Ring Security Mode Remove Ietf MIB Support Trmmim MIB Structure Chassis MGR Protocol StackSnmp Agent Network One, Network Two Brief Word About MIB Components and Community Names Telnet Trmmim MIB Structure Index Index-2 Index-3 Index-4