Board and Port, Drop | Cabletron Systems TRMMIM specification

Ring Map

The current

Calculation Mode

is displayed here

Figure 3-3. Quick Info Popup Window

The Quick Info Popup window contains the following information about the selected station:

MAC Address

The hardware address of the station’s network adapter, displayed in Canonical form.

Name

The administratively assigned name of the station, if one has been assigned; if none has been assigned, this ﬁeld will remain blank. See Setting a Station Name, page 3-8.

Board and Port

If the station is resident in the same hub as the TRMMIM, its board and port location will display here. If the station is physically remote from the monitored hub, the board and port will display 0.

Drop

The drop location of the station, if one has been administratively assigned. See Setting a Station Drop, page 3-9.

Viewing Station-speciﬁc Information

3-7

Image 57

Cabletron Systems TRMMIM manual Board and Port, Drop

Contents

Trmmim Page Virus Disclaimer Applicable to licenses to the United States Government only Restricted Rights Notice Contents Chapter Alarm Conﬁguration Chapter Ring MapChapter Statistics Appendix a Trmmim MIB Structure Chapter Ring Security Conﬁguration Contents Trmmim Using the Trmmim User’s Guide Introduction to Spma for the Trmmim What’s not in the Trmmim Guide Screen Displays Conventions Introduction to Spma for the Trmmim Button Using the Mouse FTP Getting Help Trmmim Firmware Introduction to Spma for the Trmmim Trmmim Firmware Using the Hub View Using the Trmmim Hub View Navigating Through the Hub View Using the Trmmim Hub View Trmmim Hub View Hub View Front Panel Time and Date UptimeDevice Name Device Location Using the Trmmim Hub View Using the Mouse in a Hub View Module Module Index FNB Bypass State Port Display Form Hub View Port Color Codes Frames ErrorsTotal Bytes Port Type FNB Display Monitoring Hub Performance Using the Trmmim Hub View Name and Location Checking Device Status and Updating Front Panel Info Contact Checking Module StatusDate and Time Total Rings Speed Fault Location Speed FaultModule Name Module Checking Port Status Admin StatePort Name Module/Port Checking Station Status Link State TimeInsertion Trap Station Name VendorUpstream Neighbor/Downstream Neighbor Priority Physical LocationPort Mapping Reverse MACs Conﬁguring Station Name, Location, or Priority Checking Ring Port Status Media Fault Fault State TimeClass Media Type Checking Statistics Line BytesBurst Abort Managing the Hub Managing the Hub at the Device LevelFind MAC Address 12. The Find MAC Address Window Setting the Polling Intervals Contact Status 13. Trmmim Polling Intervals Device Conﬁguration Device General StatusPort Operational State Statistics Controlling Token Ring FNB Multiplexer Connections Managing the Hub at the Module Level INS Left Connect BoardRight Connect Bypass Clearing the Module FNB Conﬁguration Window Selections Controlling Token Ring Speed Enabling All Ports on Token Ring Modules Controlling Token Ring MIM Management ModeAuto AUT Management MGT Managing the Hub at the Port Level Converting a Station Port to a Ring-out PortEnabling and Disabling Station and Ring Ports Removing a Station from the Ring Ring Map Launching the Ring Map From the command line stand-alone modeFrom the icon From the Hub View Ring Name Selecting a Ring to Map Ring Map Stations SpeedName Utilization Quick Info Popup Window Viewing Station-speciﬁc Information Drop Board and Port Performance and Errors Setting a Station Name Viewing Management Station Conﬁguration Setting a Station Drop Commands Open Status Error Status Active Monitor Error Setting the Statistics Calculation Mode Error Report TimerViewing Ring-level Information Set Calculation Mode Window Viewing the Error Table Error Table Window Isolating Errors Total Errors Non-Isolating Errors Changing the Station Labels Viewing Device Information Device Information Window Setting the Map Poll Interval Active Monitor Changes Viewing Beacon HistoryRing Purges Beacon Events Last Beacon Type Longest BeaconLast Beacon Beacon Conﬁguration 12. The Beacon Conﬁguration Window Using the Find Options 13. Sample Find Windows Searching by Station Name, MAC Address, Board/Port, or Drop Finding the Active Monitor on the Network Finding the Management Station on the Network Frames or Errors measured/Δ Time in seconds 14. Sample Find Highest and Lowest Windows Accessing Other Spma Applications Alarm Conﬁguration Spmarun e5alarms IP address community name Setting and Viewing Ring Alarms Alarm Conﬁguration Setting a Ring Level Alarm Setting and Viewing Station Alarms Alarm Conﬁguration Alarm Conﬁguration Alarm Conﬁguration Setting a Station Level Alarm Alarm Conﬁguration Setting and Viewing Station Alarms Statistics Using Statistics Spmarun e5stats IP Address community name Viewing the Ring Station List Stn Name Module and PortUpstream Addr Downstream Addr Using the Reverse MAC Button Monitoring Ring and Station StatisticsRefreshing the Station List Creating a Pie Chart Creating a Graph or Meter Click mouse button 1 on General Ring and Station VariablesProtocols KBytes Line Errors Isolating ErrorsBurst Error AC Error Non-Isolating Errors Abort ErrorInternal Error Frequency Errors Token Errors Statistics Ring and Station Variables About Ring Security Ring Security Conﬁguration Ring Security Conﬁguration Launching the Security Conﬁguration Window Security Conﬁguration Ring Selection window, -1, will appear Allowed Count Allowed Station ListDisallowed Station List Disallowed Count Security Mode Options Disable SecurityEnable Security Allowed/Disallowed List Conﬁguration Buttons Building the Allowed List Automatically Conﬁguring Security Station Addition Window Deleting Stations from the Allowed or Disallowed Lists Clear List Window Clearing All Entries in the Allowed or Disallowed List Remove Changing the Ring Security Mode Trmmim MIB Structure Ietf MIB Support Protocol Stack Chassis MGRSnmp Agent Network One, Network Two Telnet Brief Word About MIB Components and Community Names Trmmim MIB Structure Index Index-2 Index-3 Index-4