Navigating Through the Hub View | Cabletron Systems TRMMIM specs

Using the TRMMIM Hub View

The community name you use to start the module must have at least Read access; for full management functionality, you should use a community name that provides Read/Write or Superuser access. For more information on community names, consult the appropriate Installing and Using SPECTRUM for... guide, and/or the Community Names chapter in the SPMA Tools Guide.

NOTES

The spmarun script invoked ﬁrst in the above command temporarily sets the environment variables SPMA needs to operate; be sure to use this command any time you launch an application from the command line. This script is automatically invoked when you launch an application from the icon menu or from within the Hub View.

If you wish to conﬁgure your Token Ring hub in any way, be sure to use a community name with at least Read/Write access. If you only wish to view current settings, a community name with Read access will be sufﬁcient.

If there is a hostname mapped to your TRMMIM’s IP address, you can use <hostname> in place of <IP address> to launch this application. Please note, however, that the hostname is not the same as the device name which can be assigned via Local Management and/or SPMA; you cannot use the device name in place of the IP address.

Navigating Through the Hub View

Within the Hub View (Figure 2-1), you can click mouse buttons in different areas of the window to access various menus and initiate certain management tasks. The following describes the information displayed in the Hub View and shows you how to use the mouse to display the Device, Module, and Port menus.

2-2	Using the Hub View

Image 18

Cabletron Systems TRMMIM manual Navigating Through the Hub View, Using the Trmmim Hub View

Contents

Trmmim Page Virus Disclaimer Restricted Rights Notice Applicable to licenses to the United States Government only Contents Chapter Alarm Conﬁguration Chapter Ring MapChapter Statistics Chapter Ring Security Conﬁguration Appendix a Trmmim MIB Structure Contents Using the Trmmim User’s Guide Trmmim What’s not in the Trmmim Guide Introduction to Spma for the Trmmim Conventions Screen Displays Introduction to Spma for the Trmmim Using the Mouse Button Getting Help FTP Trmmim Firmware Introduction to Spma for the Trmmim Trmmim Firmware Using the Trmmim Hub View Using the Hub View Using the Trmmim Hub View Navigating Through the Hub View Hub View Front Panel Trmmim Hub View Device Name UptimeTime and Date Device Location Using the Trmmim Hub View Using the Mouse in a Hub View Module Module Index FNB Bypass State Hub View Port Color Codes Port Display Form Total Bytes ErrorsFrames Port Type FNB Display Monitoring Hub Performance Using the Trmmim Hub View Checking Device Status and Updating Front Panel Info Name and Location Date and Time Checking Module StatusContact Total Rings Module Name Speed FaultSpeed Fault Location Module Port Name Admin StateChecking Port Status Module/Port Checking Station Status Link State TimeInsertion Trap Station Name VendorUpstream Neighbor/Downstream Neighbor Port Mapping Physical LocationPriority Reverse MACs Checking Ring Port Status Conﬁguring Station Name, Location, or Priority Class Fault State TimeMedia Fault Media Type Checking Statistics Burst BytesLine Abort Managing the Hub Managing the Hub at the Device LevelFind MAC Address Setting the Polling Intervals 12. The Find MAC Address Window 13. Trmmim Polling Intervals Contact Status Port Operational State Device General StatusDevice Conﬁguration Statistics Managing the Hub at the Module Level Controlling Token Ring FNB Multiplexer Connections INS Right Connect BoardLeft Connect Bypass Controlling Token Ring Speed Clearing the Module FNB Conﬁguration Window Selections Auto AUT Controlling Token Ring MIM Management ModeEnabling All Ports on Token Ring Modules Management MGT Managing the Hub at the Port Level Converting a Station Port to a Ring-out PortEnabling and Disabling Station and Ring Ports Removing a Station from the Ring Ring Map From the icon From the command line stand-alone modeLaunching the Ring Map From the Hub View Selecting a Ring to Map Ring Name Ring Map Name SpeedStations Utilization Viewing Station-speciﬁc Information Quick Info Popup Window Board and Port Drop Setting a Station Name Performance and Errors Setting a Station Drop Viewing Management Station Conﬁguration Commands Error Status Open Status Error Active Monitor Setting the Statistics Calculation Mode Error Report TimerViewing Ring-level Information Viewing the Error Table Set Calculation Mode Window Error Table Window Total Errors Isolating Errors Non-Isolating Errors Changing the Station Labels Viewing Device Information Setting the Map Poll Interval Device Information Window Ring Purges Viewing Beacon HistoryActive Monitor Changes Beacon Events Last Beacon Type Longest BeaconLast Beacon Beacon Conﬁguration 12. The Beacon Conﬁguration Window Using the Find Options Searching by Station Name, MAC Address, Board/Port, or Drop 13. Sample Find Windows Finding the Active Monitor on the Network Finding the Management Station on the Network Frames or Errors measured/Δ Time in seconds Accessing Other Spma Applications 14. Sample Find Highest and Lowest Windows Alarm Conﬁguration Spmarun e5alarms IP address community name Setting and Viewing Ring Alarms Alarm Conﬁguration Setting and Viewing Station Alarms Setting a Ring Level Alarm Alarm Conﬁguration Alarm Conﬁguration Alarm Conﬁguration Setting a Station Level Alarm Alarm Conﬁguration Setting and Viewing Station Alarms Using Statistics Statistics Viewing the Ring Station List Spmarun e5stats IP Address community name Upstream Addr Module and PortStn Name Downstream Addr Using the Reverse MAC Button Monitoring Ring and Station StatisticsRefreshing the Station List Creating a Pie Chart Creating a Graph or Meter Click mouse button 1 on Protocols Ring and Station VariablesGeneral KBytes Burst Error Isolating ErrorsLine Errors AC Error Non-Isolating Errors Abort ErrorInternal Error Token Errors Frequency Errors Statistics Ring and Station Variables Ring Security Conﬁguration About Ring Security Launching the Security Conﬁguration Window Ring Security Conﬁguration Security Conﬁguration Ring Selection window, -1, will appear Disallowed Station List Allowed Station ListAllowed Count Disallowed Count Security Mode Options Disable SecurityEnable Security Allowed/Disallowed List Conﬁguration Buttons Conﬁguring Security Building the Allowed List Automatically Deleting Stations from the Allowed or Disallowed Lists Station Addition Window Clearing All Entries in the Allowed or Disallowed List Clear List Window Changing the Ring Security Mode Remove Ietf MIB Support Trmmim MIB Structure Snmp Agent Chassis MGRProtocol Stack Network One, Network Two Brief Word About MIB Components and Community Names Telnet Trmmim MIB Structure Index Index-2 Index-3 Index-4