Cabletron Systems TRMMIM specs

Ring Security Conﬁguration

Allowed/Disallowed List Conﬁguration Buttons

The following buttons are used to manipulate the Allowed and Disallowed Lists and to set the security mode at the device:

This button moves a selected address(es) from the

Allowed List to the Disallowed List.

Note that if you are in the Warn mode, removing a station from the Allowed List will have little effect, because the station will remain on the ring and automatically be re-added to the Allowed List (although a trap will be sent to your management workstation when the station is re-added to the list). Note that the Allowed and Disallowed Lists will refresh automatically when a station reinserts into the ring.

If no items in the Allowed List are selected, this button will be grayed out.

This button moves a selected address(es) from the Disallowed List to the Allowed List. If there are no items selected in the Disallowed List, this button will be grayed out.

Selecting this button will delete selected address(es) from the Allowed or Disallowed Station Lists.

This button is active in all security modes; however, if you have Enable Security-Warnmode selected, the station will automatically be re-added to the Allowed List. Note that the Allowed List will automatically refresh when a station is re-added.

Selecting this button will invoke a pop-up window which allows you to add a station to the Allowed or Disallowed Station List (as described in the following section). This button is only active if security is enabled.

When pressed, this button will invoke a pop-up window that allows you to remove all address(es) from the Allowed List.

This button is active in all security modes; however, if you have Enable Security-Warnmode selected, the cleared stations will simply be re-added to the list. Note that the Allowed List refreshes automatically when stations are re-added.

Selecting this button will refresh both the Allowed List (stored on the TRMMIM itself) and the Disallowed List (stored on your management workstation). Should any

6-6	Launching the Security Conﬁguration Window

Image 108

Cabletron Systems TRMMIM manual Allowed/Disallowed List Conﬁguration Buttons

Contents

Trmmim Page Virus Disclaimer Restricted Rights Notice Applicable to licenses to the United States Government only Contents Chapter Alarm Conﬁguration Chapter Ring MapChapter Statistics Chapter Ring Security Conﬁguration Appendix a Trmmim MIB Structure Contents Using the Trmmim User’s Guide Trmmim What’s not in the Trmmim Guide Introduction to Spma for the Trmmim Conventions Screen Displays Introduction to Spma for the Trmmim Using the Mouse Button Getting Help FTP Trmmim Firmware Introduction to Spma for the Trmmim Trmmim Firmware Using the Trmmim Hub View Using the Hub View Using the Trmmim Hub View Navigating Through the Hub View Hub View Front Panel Trmmim Hub View Uptime Time and DateDevice Name Device Location Using the Trmmim Hub View Using the Mouse in a Hub View Module Module Index FNB Bypass State Hub View Port Color Codes Port Display Form Errors FramesTotal Bytes Port Type FNB Display Monitoring Hub Performance Using the Trmmim Hub View Checking Device Status and Updating Front Panel Info Name and Location Checking Module Status ContactDate and Time Total Rings Speed Fault Speed Fault LocationModule Name Module Admin State Checking Port StatusPort Name Module/Port Checking Station Status Link State TimeInsertion Trap Station Name VendorUpstream Neighbor/Downstream Neighbor Physical Location PriorityPort Mapping Reverse MACs Checking Ring Port Status Conﬁguring Station Name, Location, or Priority Fault State Time Media FaultClass Media Type Checking Statistics Bytes LineBurst Abort Managing the Hub Managing the Hub at the Device LevelFind MAC Address Setting the Polling Intervals 12. The Find MAC Address Window 13. Trmmim Polling Intervals Contact Status Device General Status Device ConﬁgurationPort Operational State Statistics Managing the Hub at the Module Level Controlling Token Ring FNB Multiplexer Connections INS Board Left ConnectRight Connect Bypass Controlling Token Ring Speed Clearing the Module FNB Conﬁguration Window Selections Controlling Token Ring MIM Management Mode Enabling All Ports on Token Ring ModulesAuto AUT Management MGT Managing the Hub at the Port Level Converting a Station Port to a Ring-out PortEnabling and Disabling Station and Ring Ports Removing a Station from the Ring Ring Map From the command line stand-alone mode Launching the Ring MapFrom the icon From the Hub View Selecting a Ring to Map Ring Name Ring Map Speed StationsName Utilization Viewing Station-speciﬁc Information Quick Info Popup Window Board and Port Drop Setting a Station Name Performance and Errors Setting a Station Drop Viewing Management Station Conﬁguration Commands Error Status Open Status Error Active Monitor Setting the Statistics Calculation Mode Error Report TimerViewing Ring-level Information Viewing the Error Table Set Calculation Mode Window Error Table Window Total Errors Isolating Errors Non-Isolating Errors Changing the Station Labels Viewing Device Information Setting the Map Poll Interval Device Information Window Viewing Beacon History Active Monitor ChangesRing Purges Beacon Events Last Beacon Type Longest BeaconLast Beacon Beacon Conﬁguration 12. The Beacon Conﬁguration Window Using the Find Options Searching by Station Name, MAC Address, Board/Port, or Drop 13. Sample Find Windows Finding the Active Monitor on the Network Finding the Management Station on the Network Frames or Errors measured/Δ Time in seconds Accessing Other Spma Applications 14. Sample Find Highest and Lowest Windows Alarm Conﬁguration Spmarun e5alarms IP address community name Setting and Viewing Ring Alarms Alarm Conﬁguration Setting and Viewing Station Alarms Setting a Ring Level Alarm Alarm Conﬁguration Alarm Conﬁguration Alarm Conﬁguration Setting a Station Level Alarm Alarm Conﬁguration Setting and Viewing Station Alarms Using Statistics Statistics Viewing the Ring Station List Spmarun e5stats IP Address community name Module and Port Stn NameUpstream Addr Downstream Addr Using the Reverse MAC Button Monitoring Ring and Station StatisticsRefreshing the Station List Creating a Pie Chart Creating a Graph or Meter Click mouse button 1 on Ring and Station Variables GeneralProtocols KBytes Isolating Errors Line ErrorsBurst Error AC Error Non-Isolating Errors Abort ErrorInternal Error Token Errors Frequency Errors Statistics Ring and Station Variables Ring Security Conﬁguration About Ring Security Launching the Security Conﬁguration Window Ring Security Conﬁguration Security Conﬁguration Ring Selection window, -1, will appear Allowed Station List Allowed CountDisallowed Station List Disallowed Count Security Mode Options Disable SecurityEnable Security Allowed/Disallowed List Conﬁguration Buttons Conﬁguring Security Building the Allowed List Automatically Deleting Stations from the Allowed or Disallowed Lists Station Addition Window Clearing All Entries in the Allowed or Disallowed List Clear List Window Changing the Ring Security Mode Remove Ietf MIB Support Trmmim MIB Structure Chassis MGR Protocol StackSnmp Agent Network One, Network Two Brief Word About MIB Components and Community Names Telnet Trmmim MIB Structure Index Index-2 Index-3 Index-4