Open Status, Error Status | Cabletron Systems TRMMIM instruction

Ring Map

Open Status

This ﬁeld displays the result of the last “open” command or the last attempt by the management station to open onto the ring: whether the management station did in fact open onto the ring, or if an error occurred. This ﬁeld may display any one of the following:

No Open	An open command has not been issued.
Bad Param	The open command could not be completed because the
	parameters did not allow for the station to be opened
	onto the ring.
Lobe Test Failed	The lobe media check has failed for the management
	station.
Signal Loss	A signal loss condition has been detected at the
	management station’s receiver input during the open
	process.
Insertion Timeout	The management station has failed to logically insert on
	the ring before the insertion timer expires.
Purge Failed	The management station has timed out when attempting
	a ring purge after becoming the active monitor: that is,
	the management station was unable to receive its own
	ring purge MAC frames.
Beaconing	The management station received a beacon MAC frame
	after physically inserting into the ring.
Duplicate MAC	Another station on the ring has the same MAC address
Address	as the management station.
Parameter Requested	The management station has determined that a Ring
	Parameter Server (RPS) is present on the ring, but it does
	not respond to a request initialization MAC frame.
Remove Received	The management station received a remove adapter
	MAC frame during the insertion process.
Open	The open command was completed successfully.

Error Status

This ﬁeld displays a number associated with the most recent error status that was reported by the management station. It is possible for more than one error status to be reported at one time; in this case, the number displayed would be the sum of the codes of the last errors recorded. The following table lists the possible errors and their corresponding error codes:

Viewing Station-speciﬁc Information

3-11

Image 61

Cabletron Systems TRMMIM manual Open Status, Error Status

Contents

Trmmim Page Virus Disclaimer Applicable to licenses to the United States Government only Restricted Rights Notice Contents Chapter Ring Map Chapter Alarm ConﬁgurationChapter Statistics Appendix a Trmmim MIB Structure Chapter Ring Security Conﬁguration Contents Trmmim Using the Trmmim User’s Guide Introduction to Spma for the Trmmim What’s not in the Trmmim Guide Screen Displays Conventions Introduction to Spma for the Trmmim Button Using the Mouse FTP Getting Help Trmmim Firmware Introduction to Spma for the Trmmim Trmmim Firmware Using the Hub View Using the Trmmim Hub View Navigating Through the Hub View Using the Trmmim Hub View Trmmim Hub View Hub View Front Panel Time and Date UptimeDevice Name Device Location Using the Trmmim Hub View Using the Mouse in a Hub View Module Module Index FNB Bypass State Port Display Form Hub View Port Color Codes Frames ErrorsTotal Bytes Port Type FNB Display Monitoring Hub Performance Using the Trmmim Hub View Name and Location Checking Device Status and Updating Front Panel Info Contact Checking Module StatusDate and Time Total Rings Speed Fault Location Speed FaultModule Name Module Checking Port Status Admin StatePort Name Module/Port Link State Time Checking Station StatusInsertion Trap Vendor Station NameUpstream Neighbor/Downstream Neighbor Priority Physical LocationPort Mapping Reverse MACs Conﬁguring Station Name, Location, or Priority Checking Ring Port Status Media Fault Fault State TimeClass Media Type Checking Statistics Line BytesBurst Abort Managing the Hub at the Device Level Managing the HubFind MAC Address 12. The Find MAC Address Window Setting the Polling Intervals Contact Status 13. Trmmim Polling Intervals Device Conﬁguration Device General StatusPort Operational State Statistics Controlling Token Ring FNB Multiplexer Connections Managing the Hub at the Module Level INS Left Connect BoardRight Connect Bypass Clearing the Module FNB Conﬁguration Window Selections Controlling Token Ring Speed Enabling All Ports on Token Ring Modules Controlling Token Ring MIM Management ModeAuto AUT Management MGT Converting a Station Port to a Ring-out Port Managing the Hub at the Port LevelEnabling and Disabling Station and Ring Ports Removing a Station from the Ring Ring Map Launching the Ring Map From the command line stand-alone modeFrom the icon From the Hub View Ring Name Selecting a Ring to Map Ring Map Stations SpeedName Utilization Quick Info Popup Window Viewing Station-speciﬁc Information Drop Board and Port Performance and Errors Setting a Station Name Viewing Management Station Conﬁguration Setting a Station Drop Commands Open Status Error Status Active Monitor Error Error Report Timer Setting the Statistics Calculation ModeViewing Ring-level Information Set Calculation Mode Window Viewing the Error Table Error Table Window Isolating Errors Total Errors Non-Isolating Errors Changing the Station Labels Viewing Device Information Device Information Window Setting the Map Poll Interval Active Monitor Changes Viewing Beacon HistoryRing Purges Beacon Events Longest Beacon Last Beacon TypeLast Beacon Beacon Conﬁguration 12. The Beacon Conﬁguration Window Using the Find Options 13. Sample Find Windows Searching by Station Name, MAC Address, Board/Port, or Drop Finding the Active Monitor on the Network Finding the Management Station on the Network Frames or Errors measured/Δ Time in seconds 14. Sample Find Highest and Lowest Windows Accessing Other Spma Applications Alarm Conﬁguration Spmarun e5alarms IP address community name Setting and Viewing Ring Alarms Alarm Conﬁguration Setting a Ring Level Alarm Setting and Viewing Station Alarms Alarm Conﬁguration Alarm Conﬁguration Alarm Conﬁguration Setting a Station Level Alarm Alarm Conﬁguration Setting and Viewing Station Alarms Statistics Using Statistics Spmarun e5stats IP Address community name Viewing the Ring Station List Stn Name Module and PortUpstream Addr Downstream Addr Monitoring Ring and Station Statistics Using the Reverse MAC ButtonRefreshing the Station List Creating a Pie Chart Creating a Graph or Meter Click mouse button 1 on General Ring and Station VariablesProtocols KBytes Line Errors Isolating ErrorsBurst Error AC Error Abort Error Non-Isolating ErrorsInternal Error Frequency Errors Token Errors Statistics Ring and Station Variables About Ring Security Ring Security Conﬁguration Ring Security Conﬁguration Launching the Security Conﬁguration Window Security Conﬁguration Ring Selection window, -1, will appear Allowed Count Allowed Station ListDisallowed Station List Disallowed Count Disable Security Security Mode OptionsEnable Security Allowed/Disallowed List Conﬁguration Buttons Building the Allowed List Automatically Conﬁguring Security Station Addition Window Deleting Stations from the Allowed or Disallowed Lists Clear List Window Clearing All Entries in the Allowed or Disallowed List Remove Changing the Ring Security Mode Trmmim MIB Structure Ietf MIB Support Protocol Stack Chassis MGRSnmp Agent Network One, Network Two Telnet Brief Word About MIB Components and Community Names Trmmim MIB Structure Index Index-2 Index-3 Index-4