Viewing the Ring Station List | Cabletron Systems TRMMIM specification

Statistics

from the command line (stand-alone mode):

1. From the appropriate directory, type:

spmarun e5stats <IP Address> <community name>

NOTES

The spmarun script invoked ﬁrst in the above command temporarily sets the environment variables SPMA needs to operate; be sure to use this command any time you launch an application from the command line. This script is automatically invoked when you launch an application from the icon menu or from within the Hub View.

A community name with Read access will be sufﬁcient to view the statistics.

If there is a hostname mapped to your TRMMIM’s IP address, you can use <hostname> in place of <IP address> to launch this application. Please note, however, that the hostname is not the same as the device name which can be assigned via Local Management and/or SPMA; you cannot use the device name in place of the IP address.

The Ring/Stn Statistics window, Figure 5-1, will appear.

Figure 5-1. The Ring/Stn Statistics Window

This window lists the interfaces with their corresponding numbers that are available on your Token Ring device. Use the scroll bar on the side of the display window if necessary to see the full list of Ring Names. This window allows you to choose a ring and then display the Ring and Station Statistics window speciﬁc to that ring. You may also quit the Token Ring statistics tool from this window by

clicking mouse button 1 on .

Viewing the Ring Station List

From the Ring/Stn Statistics window, select the network from which you would

like to gather statistics and click mouse button 1 on . The Ring and Station Statistics window, Figure 5-2, will appear.

5-2	Viewing the Ring Station List

Image 92

Cabletron Systems TRMMIM manual Viewing the Ring Station List, Spmarun e5stats IP Address community name

Contents

Trmmim Page Virus Disclaimer Restricted Rights Notice Applicable to licenses to the United States Government only Contents Chapter Statistics Chapter Alarm ConﬁgurationChapter Ring Map Chapter Ring Security Conﬁguration Appendix a Trmmim MIB Structure Contents Using the Trmmim User’s Guide Trmmim What’s not in the Trmmim Guide Introduction to Spma for the Trmmim Conventions Screen Displays Introduction to Spma for the Trmmim Using the Mouse Button Getting Help FTP Trmmim Firmware Introduction to Spma for the Trmmim Trmmim Firmware Using the Trmmim Hub View Using the Hub View Using the Trmmim Hub View Navigating Through the Hub View Hub View Front Panel Trmmim Hub View Uptime Time and DateDevice Name Device Location Using the Trmmim Hub View Using the Mouse in a Hub View Module Module Index FNB Bypass State Hub View Port Color Codes Port Display Form Errors FramesTotal Bytes Port Type FNB Display Monitoring Hub Performance Using the Trmmim Hub View Checking Device Status and Updating Front Panel Info Name and Location Checking Module Status ContactDate and Time Total Rings Speed Fault Speed Fault LocationModule Name Module Admin State Checking Port StatusPort Name Module/Port Insertion Trap Checking Station StatusLink State Time Upstream Neighbor/Downstream Neighbor Station NameVendor Physical Location PriorityPort Mapping Reverse MACs Checking Ring Port Status Conﬁguring Station Name, Location, or Priority Fault State Time Media FaultClass Media Type Checking Statistics Bytes LineBurst Abort Find MAC Address Managing the HubManaging the Hub at the Device Level Setting the Polling Intervals 12. The Find MAC Address Window 13. Trmmim Polling Intervals Contact Status Device General Status Device ConﬁgurationPort Operational State Statistics Managing the Hub at the Module Level Controlling Token Ring FNB Multiplexer Connections INS Board Left ConnectRight Connect Bypass Controlling Token Ring Speed Clearing the Module FNB Conﬁguration Window Selections Controlling Token Ring MIM Management Mode Enabling All Ports on Token Ring ModulesAuto AUT Management MGT Enabling and Disabling Station and Ring Ports Managing the Hub at the Port LevelConverting a Station Port to a Ring-out Port Removing a Station from the Ring Ring Map From the command line stand-alone mode Launching the Ring MapFrom the icon From the Hub View Selecting a Ring to Map Ring Name Ring Map Speed StationsName Utilization Viewing Station-speciﬁc Information Quick Info Popup Window Board and Port Drop Setting a Station Name Performance and Errors Setting a Station Drop Viewing Management Station Conﬁguration Commands Error Status Open Status Error Active Monitor Viewing Ring-level Information Setting the Statistics Calculation ModeError Report Timer Viewing the Error Table Set Calculation Mode Window Error Table Window Total Errors Isolating Errors Non-Isolating Errors Changing the Station Labels Viewing Device Information Setting the Map Poll Interval Device Information Window Viewing Beacon History Active Monitor ChangesRing Purges Beacon Events Last Beacon Last Beacon TypeLongest Beacon Beacon Conﬁguration 12. The Beacon Conﬁguration Window Using the Find Options Searching by Station Name, MAC Address, Board/Port, or Drop 13. Sample Find Windows Finding the Active Monitor on the Network Finding the Management Station on the Network Frames or Errors measured/Δ Time in seconds Accessing Other Spma Applications 14. Sample Find Highest and Lowest Windows Alarm Conﬁguration Spmarun e5alarms IP address community name Setting and Viewing Ring Alarms Alarm Conﬁguration Setting and Viewing Station Alarms Setting a Ring Level Alarm Alarm Conﬁguration Alarm Conﬁguration Alarm Conﬁguration Setting a Station Level Alarm Alarm Conﬁguration Setting and Viewing Station Alarms Using Statistics Statistics Viewing the Ring Station List Spmarun e5stats IP Address community name Module and Port Stn NameUpstream Addr Downstream Addr Refreshing the Station List Using the Reverse MAC ButtonMonitoring Ring and Station Statistics Creating a Pie Chart Creating a Graph or Meter Click mouse button 1 on Ring and Station Variables GeneralProtocols KBytes Isolating Errors Line ErrorsBurst Error AC Error Internal Error Non-Isolating ErrorsAbort Error Token Errors Frequency Errors Statistics Ring and Station Variables Ring Security Conﬁguration About Ring Security Launching the Security Conﬁguration Window Ring Security Conﬁguration Security Conﬁguration Ring Selection window, -1, will appear Allowed Station List Allowed CountDisallowed Station List Disallowed Count Enable Security Security Mode OptionsDisable Security Allowed/Disallowed List Conﬁguration Buttons Conﬁguring Security Building the Allowed List Automatically Deleting Stations from the Allowed or Disallowed Lists Station Addition Window Clearing All Entries in the Allowed or Disallowed List Clear List Window Changing the Ring Security Mode Remove Ietf MIB Support Trmmim MIB Structure Chassis MGR Protocol StackSnmp Agent Network One, Network Two Brief Word About MIB Components and Community Names Telnet Trmmim MIB Structure Index Index-2 Index-3 Index-4