ESC J n, Ff, Esc L, Esc S | Citizen CT-S300 manual

ESC FF

[Function]	Printing data in PAGE MODE
[Code]	<1B>H<0C>H
[Outline]	Executes a batch printout of the data mapped in the entire print area in PAGE MODE.
[Caution]	•	This command is only effective when PAGE MODE is selected.
	•	Mapped data, as well as the ESC T and ESC W settings, and the character mapping
		position are held even after printing.
[See Also]	Appendix 4.1 “Explanation on PAGE MODE”
	FF, ESC L, ESC S

ESC J n

[Function]	Printing and feeding paper in minimum pitch
[Code]	<1B>H<4A>H<n>
[Range]	0	n 255
[Outline]	Prints the data held in the print buffer and feeds paper by [n ⋅ basic calculation pitch]
	inches.
[Caution]	•	After this command is executed, the beginning of the line is taken as the start position
		for the next print.
	•	The line feed width can be set separately for the STANDARD and PAGE MODES.
	•	This command does not affect the line feed width defined by ESC 2 or ESC 3.
	•	The basic calculation pitch is set by GS P.
	•	Fractions resulting from calculation are corrected with the minimum pitch of the
		mechanism, and the remainder is omitted.
	•	In STANDARD MODE, this command uses the vertical (paper feed direction) basic
		calculation pitch (y).
	•	In PAGE MODE, this command acts differently depending on the start point:
		(1) If the start point specified by ESC T is top left or bottom right, the command
		uses the vertical (Paper feed direction) basic calculation pitch (y).
		(2) If the start point specified by ESC T is top right or bottom left, the command
		uses the horizontal (Perpendicular to the paper feed direction) basic calculation
		pitch (x).
		The maximum settable line feed width is 1016 mm (40 inches). A setting greater
		than this maximum is trimmed to the maximum.
[Default]	The initial value is not defined.
[Sample Program]	Refer to Sample Program and Print Results for ESC 2.

— 10 —

Image 15

Citizen CT-S300 manual ESC J n, Ff, Esc L, Esc S

Contents

Command Reference Revision Table of Contents Macro Commands Character Code Table Program coding Example Print Control Commands Function Mode CommandPrint Character Commands Function Mode Status Commands Function Mode Print Position Commands Function ModeLine Feed Span Commands Function Mode Bit Image Commands Function Mode Bar Code Commands Function Mode Panel Switch Commands Function ModeMacro Commands Function Mode Cutter Commands Function Mode Other Commands Function Mode Printer Function Setting Commands Mode Outline DefaultCode Range Sample Program Command Details See Also Sample Program ESC FF, ESC L, ESC S FF, ESC L, ESC S ESC J n ESC d n Default Sample Program Print Results ESC L, ESC W Can ESC SP n Default See Also Bit Function Value ESC ! n Lprint CHR$&HA ESC ESC % n MSB LSB ESC & s n m a p s ⋅ a m-n+1 ESC n ESC ? n ESC E n ESC G n Character Set ESC M nESC R n Range Outline ESC V n Default Sample Program Character Code Table ESC t n Condition Black-based Paper Red-based Paper ESC ~ J n Valid in CBM1000II-Compatible Mode DC3 n Valid in CBM1000II-Compatible Mode Vertical Magnification Hex Decimal GS ! nBit Function Value Hex. Number Decimal Number Horizontal Magnification Hex Decimal GS B n 1DH62Hn Printing Result Print Position Commands ESC $ n1 n2 ESC D n k Null Printing Direction Start Point CAN, ESC L, ESC T, GS P ESC W xL xH yL yH dxL dxH dyL dyH ESC \ nL nH Position ESC a n GS $ nL nH GS P, GS W GS L nL nH GS W nL nH GS L, GS P GS \ nL nH ESC ESC 2, GS P ESC 3 n ESC * m n1 n2 d k IMG1 GS * n1 n2 d n1 ⋅ n2 ⋅ Gosub IMG See Also ESC &, GS GS / m GS v 0 m xL xH yL yH d1...dk Msblsb Status DLE EOT n Bit Status Hex Decimal Status caused by an error when n = 3 is specified Bit Status Item Addressed by ASB Hex Decimal GS a n 1st byte Printer information 4th byte Paper Sensor information GS r n Drawer kick-out connector status n = 2 Bit Position Value ESC c 3 n ESC c 4 n ESC c 5 n Macro Commands GS n1 n2 n3 GS V m GS V m n Printing Position GS H n Print Results Font GS f n 1DH68Hn GS k m d1 ...... dk Null GS k m n d1 ...... dn Bar Code System Range of k Range of dBar Code System Range of n Range of d For Standard Mode For page ModeFor UPC-E Description of Bar Codes DEL Control Character HRI Character Code Set a Code Set B Code Set C Special characters Hex JAN-8 Type Print Sample Outline of SymbolBar Code Print Example UPC-A GS w n See Also ESC *, FS q, GS /, GS v P n m Q n xL xH yL yH d1…dk 1… xL xH yL yH d1…dk n Example When xL = 64, xH = 0, yL = 96, yH = GS Valid Only at B.M Paper Selection GS FF Valid Only at B.M Paper Selection GS a m n Valid Only at B.M Paper Selection Correcting DirectionFF, GS GS C0 m n GS C1 n1 n2 n3 n4 n5 n6 GS C2 n1 n2 GS C n1 n2 n3 n4 n5 Sample Program Print Results GS c GS I n1L n1H n2L n2H GS D pL pH m a1 b1 ··· ak bk Default Kind of Real-time Command Function No. fn GS E pL pH fn ··· Null Hex No. of Data 1dH28H45pL pH fn d1 d2 d3 Set Value Function Setting memory switch 2 a = Setting memory switch 4 a = 1dH28H45pL pH fn a NL + nH ⋅ Printing Density NL + nH ⋅ Paper Width NL + nH ⋅ ACK Output Position NL + nH ⋅ Printing SpeedNL + nH ⋅ No. of Divisions for Conducting Head NL + nH ⋅ Paper Sending Data 1st Byte 2nd Byte 3rd Byte 1FH Divisions Amount Setting Status Sending Data StoredControl 1st Byte 2nd Byte 3rd Byte 4th Byte 5th Byte = 209 PNE sensor judgment time Font Type Dy ⋅ xk Fn = 1dH28H45pL pH fn x c1 c2 y d1...dyXxk 1dH28H45pL pH fn c1 c2 Flow Control Parity SettingSetting Data Length Baud Rate Set value PL + pH ⋅ 256 = Fn = = 3, 5, 11 GS K pL pH fn m 1dH28H4BpL pH fn m Fn = 4, 48 m No. of Divisions for Head Conducting ESC SP, ESC 2, ESC Commands for this function Command TypeGS M pL pH fn m ESC !, ESC -, ESC E, ESC G, ESC Fn = 2, 50 Function GS M pL pH fn m Fn = 1, 49 Function GS M pL pH fn m fn = 1 Fn = 3, 51 Function GS M pL pH fn m fn = 3 Default Outline GS N pL pH fn mFn = 48 Function GS N pL pH fn m fn = DLE ENQ n DLE DC4 fn m t Specification of fn = Hex Decimal No. of Data DLE DC4 fn d1...d7 Specification of fn = Bit Equipment Value ESC = n ESC @ G3S W FS PFF, CAN, ESC FF, ESC S, ESC T, ESC W, GS W, GS \ ESC S ESC p m n1 n2 Category of Test Printing Standard ModeGS a pL pH n m Category of Paper CBM Type of Printer ID Specification Value HexGS I n Kind of Printer Information 127 GS P x y ESC RS Character Code Table Codepage 00H to 7FH & Katakana Codepage 00H to 7FH & PC850 Multilingual Codepage 00H to 7FH & PC860 Portuguese Codepage 00H to 7FH & PC863 Canadian-French Codepage 00H to 7FH & PC865 Nordic Codepage 00H to 7FH & PC852 Eastern Europe Codepage 00H to 7FH & PC857 Russian Codepage 00H to 7FH & PC857 Turkish Codepage 00H to 7FH & PC864 Arabic Codepage 00H to 7FH & WPC1252 International Character Code Table Standard Mode ESC L ESC S ESC FF ModeSwitching Between Standard Mode and page Mode Mapping of Print Data in the Print Area Example of Using page Mode Example 2 Result of Print Print Result of Adding a Program of Example 3 to Example Overview Bidirectional Parallel Interface Negotiation Negotiation Procedure When 76543210 Supported Printer Precautions Data Communication from Printer to Host Nibble Mode Byte Mode Device ID CLS PrinterTermination Identification of Send Status Command and Function XONXoff