Basic setting and operation | Eiki QXXAVC922---P specification

Chapter 6 Basic setting and operation

2.Select either "Manual" or "DHCP" from IP configuration pull down menu. When "DHCP" is selected, IP address, Subnet mask, Default Gateway, DNS are automatically configured by DHCP function. Only the DNS address allows you to set up manually if the DNS address information is not provided on your DHCP server. When selecting "Manual", configure all the items manu- ally. For further information, contact your network administra- tor. The address must be entered as 4 number groups separated by a dot like [192.168.001.101].

3.After completing the network configuration, press Regist but- ton to register the network information. The Simple(Wireless) setting is fixed, which cannot be changed from factory default value.

4.To apply the setting, press Set button. The network of the pro-

jector starts re-booting and applies the setting. It takes about 20 seconds to complete. Close the web browser and access to the login page again in 20 seconds.

On the screen of the projector, the “Please wait...” message will appear and switching operation will start. Switching will take a while and after completing the operation, the “Ready for use” message will appear. During the switching period, the projector cannot be operated.

When you use LAN4(wireless) or LAN5(Wireless), the setting items of page [2] and [3] are activated and you can setup Wireless LAN setting and Security setting. See the item "Wireless LAN Setting and Security Setting" for further setting.

52

Image 52

Eiki QXXAVC922---P owner manual Basic setting and operation

Contents

Network Set-up and Operation Federal Communications Commission Notice For Canadian UsersFCC Warning FCC RF Exposure Warning Bestimmungen der Richtlinie 1999/5/EG befindet Expression/Abbreviation Trademarks and CopyrightUse of this manual Table of contents 109 127 Required operating environment for computers Network specifications of the projector Wireless LANLAN Terminal Compliance Chapter About LAN functions Image projecting system via LAN LAN functions and the featuresFlow of Image Transfer An example of the connection LAN connection modes Operate the computer mouse with the remote control About LAN functions Setup procedures Install the software on computers LAN and set the configurationNetwork Configuration has completed Select Wired LAN or Wireless LAN then connect Installing the software Network Viewer & Capture 4 installation Setup procedures Installed software Following 3 softwares are installed on your computerNetwork Capture Network Viewer 4 File Converter File Converter 2 installation Installed software and places Names and functions of the operation screen Network connection standby display Network Capture 4 window Parts Names and Functions of the Screen Using the multiple network adaptors Wired LAN configurations Connecting to the LAN line Network environment settings Description Confirming the operation Confirming the operation Network PIN code Wired factory defaultNetwork information Wired LAN factory default settings Selected LAN Wired LAN configurations Wireless LAN configurations Setting the network environment Setting procedures Identifier of the wireless access point WPA2-PSK are not available Configuring security with the projector Use of security type WEP Available PSK key characters Digits Easy wireless setting Error Screen Wireless factory default Computer environment and Wireless LAN connection Wireless indicator display Wireless LAN factory default settings Selected LAN Basic setting and operation Select a display mode and login Starting up the BrowserMended for standard use Multi-control functions Display of main setting Main setting page in the Standard Mode displaySetting Main menu How to use the setting Main setting page in the Light Mode displaySetting Pallet Sub menu tab Numbers Type of the setting pallet Text box settingPull-down menu setting Radio button setting Initial setting Switches PJLink password authentication on or offPassword for PJLink function Japanese PJLink and password setting Network PIN code settingWhats PJLink? Auto setting Date and time settingManual setting Network configuration Setting of LANSelects LAN1 to LAN5 and Simple Sets Dhcp or Manual Basic setting and operation Configuring wireless LAN setting and security setting Configuring wireless LAN setting Configuring wireless LAN security setting ItemDescription Mail setting Setting Smtp server and administrator address Registering and deleting E-mail addresses Option selection for sending alert mailUp to 10 E-mail addresses can be registered Check / Delete Option Examples Type and contents of alert mail When PJ lamp replacement time is reached When lamp corres. value reaches preselect use time Snmp setting Enter user name of the projector etc. optionalEnter place of the projector optional Community Trap Trap check/deleteCheck and delete the trap address Public Trap option setting Up to 99,999 hours can be set for the time settingItem Auto Display setting and control page 3+p.123 Trap option Basic setting and operation Controlling the projector PJ status Power control and status checkPJ temp About projector condition Status Description Controls Input System Image adjustment Image mode Video Computer Sound Adjusts the sound volume from the speakersSuppresses the sound PC adjustment Setting up the projector Screen mode VideoTable below Normal True Full Zoom Natural wide Custom Sets Auto PC Adjustment mode Sets Auto Keystone modeSets the auto-input signal detection mode Standby mode Lamp counter resetting Reset the time after lamp replaced How to set the timer Timer settingSet a day or date Check the timer events Change the event modeSet an execute time Select an event action Projector Power Event Projector information Items Description Indication of the lamp status Status Multi-control Controlling and setting the multi-projectorsExample of multi control Stops multi control function Start/stop the multi controlMenu are linked to the main menu Register the projector Confirmation of registered projector Mode Operation Change the mode of the registered projectorStatus Check & Change page in the light mode Setting all togetherCheck & Change page in the light mode Controlling all together Viewer auto setting all together Network capture functions About Network Capture function Start up the Network CaptureReal Time Capture +p.89 Network Communication +p.94 Commands on the task bar Menu during Real time capturingMenu during Network Communication Menu during Moderator function Parameter set up Using the Real Time Capture Registering the computers Control by the computer Start capturing of the PC1 from the PC5 Control by the web browserTime capturing operation Control by the projector Start capturing of the computer PC1 by using the projector Setting conditionExample of advanced use Start the presentation Using the Network Communication PC6 Settings before using the Network Communication Perform capture setting following to the description belowProjector can find up to 30 computers in the network Up to 30 computers can be registered to the projector Menu tree Description of capture editing window Command Tool Tool bar button namesBar of Sub PC Color tool bar Attribute tool bar How to use the Network communication Setting of the drawing tool attribute Edit capture imageDrawing figures Erase drawn objects Letter attribute setting 100Drawing letter Up to 1000 characters can be used for a letter frame Network Communication operation and change of state 101Preparation On the Communication Executing the forcing mode 102 Moderator function 103Projector Moderator Clients Preparation for using the moderator function Normal mode application windowModerator mode application window 104 Using the moderator function 105Description of application window Moderator operation Unregister moderator status Moderators password setting up106 Error messages Cause and corresponding Error information107 108 Network viewer functions 109 How to use the Network Viewer 4 File Converter Creating the available data Network Viewer110 Start up and quit the File Converter Command Tool Button Creating the available data111 Menu Sub Menu Description View Network viewer functions Setting of output destination and conversion mode Conversion modeOutput destination 113 Select a folder and click Save button Creating a program file Program Editor Procedure of making program115 Program file 116List 117 Setting up the display order and time of the imagesSub menu Description Blue frame Image frame on the index windowRed frame Shows that image is deleted from the folder This function is not available in the light mode Example of the created program selection119 Limitation of the Program file Using the Network Viewer function Select Network for input mode previously120 Condition to use the Network Viewer function Setup the setting page 2 of the Selection Display Setup the setting page 1 of the Visual display121 122 Auto Display setting and control Error info123 Means endless play Error information Error type124 Description 125 Display time Repeat times 126 Appendix 127 When the word Hello is replied, login has been succeeded Password 1234 is used for the exampleUse of telnet 128 Command Function 129 Web browser setting Active Script/JavaScript enableFlash Player enable Proxy setting ActiveX controls and plug-ins setting Windows XP Professional131 Examples OS/Browsers Flash Player Add-on setting Using proxy serverNot using proxy server 132 133 Flash Player Plug-in settingNetscape Navigator 134 Firewall setting Click OK to close setting135 On recommended Checked Dont allow exceptions Unchecked Troubleshooting 136 137 Infrastructure ModeCannot start up the browser 138 Cannot be turned on/off with the web browser 139 Speed of playing back images are very slow Microsoft power point format .ppt 140Images from the file server don’t appear on the screen? Cannot make a new program file 141 Terminology 142 143 Deutschland & Österreich