Start/stop the multi control | Eiki QXXAVC922---P manual

Chapter 7 Controlling the projector

Start/stop the multi control

To start or stop controlling the multi-projectors, click Multi con- trol setting menu and select ON or OFF.

Multi control setting

OFF	Stops multi control function
ON	Starts multi control function. The multi control
	menu will appear when ON is set. These items of
	menu are linked to the main menu.

Switches on and off the multi-control function

The multi controllable menus are "Power & Status", "PC adjust- ment", "Control", "Setting", "E-mail setting", "Timer", "SNMP set- ting" and "Network Viewer". Click each menu and perform set- ting and adjustment.

✐The word "MULTI CONTROL" appears on the each control page while the multi control is operating.

This shows the multi control is operating now.

80

Image 80

Eiki QXXAVC922---P Start/stop the multi control, Stops multi control function, Menu are linked to the main menu

Contents

Network Set-up and Operation Federal Communications Commission Notice For Canadian UsersFCC Warning FCC RF Exposure Warning Bestimmungen der Richtlinie 1999/5/EG befindet Use of this manual Trademarks and CopyrightExpression/Abbreviation Table of contents 109 127 Required operating environment for computers Network specifications of the projector Wireless LANLAN Terminal Compliance Chapter About LAN functions Flow of Image Transfer LAN functions and the featuresImage projecting system via LAN An example of the connection LAN connection modes Operate the computer mouse with the remote control About LAN functions Setup procedures Install the software on computers LAN and set the configurationNetwork Configuration has completed Select Wired LAN or Wireless LAN then connect Installing the software Network Viewer & Capture 4 installation Setup procedures Installed software Following 3 softwares are installed on your computerNetwork Capture Network Viewer 4 File Converter File Converter 2 installation Installed software and places Names and functions of the operation screen Network connection standby display Network Capture 4 window Parts Names and Functions of the Screen Using the multiple network adaptors Wired LAN configurations Connecting to the LAN line Network environment settings Description Confirming the operation Confirming the operation Network information Wired factory defaultNetwork PIN code Wired LAN factory default settings Selected LAN Wired LAN configurations Wireless LAN configurations Setting the network environment Setting procedures Identifier of the wireless access point WPA2-PSK are not available Configuring security with the projector Use of security type WEP Available PSK key characters Digits Easy wireless setting Error Screen Wireless factory default Computer environment and Wireless LAN connection Wireless indicator display Wireless LAN factory default settings Selected LAN Basic setting and operation Select a display mode and login Starting up the BrowserMended for standard use Multi-control functions Display of main setting Main setting page in the Standard Mode displaySetting Main menu How to use the setting Main setting page in the Light Mode displaySetting Pallet Sub menu tab Numbers Type of the setting pallet Text box settingPull-down menu setting Radio button setting Initial setting Switches PJLink password authentication on or offPassword for PJLink function Japanese Whats PJLink? Network PIN code settingPJLink and password setting Manual setting Date and time settingAuto setting Network configuration Setting of LANSelects LAN1 to LAN5 and Simple Sets Dhcp or Manual Basic setting and operation Configuring wireless LAN setting and security setting Configuring wireless LAN setting Configuring wireless LAN security setting ItemDescription Mail setting Setting Smtp server and administrator address Registering and deleting E-mail addresses Option selection for sending alert mailUp to 10 E-mail addresses can be registered Check / Delete Option Examples Type and contents of alert mail When PJ lamp replacement time is reached When lamp corres. value reaches preselect use time Snmp setting Enter user name of the projector etc. optionalEnter place of the projector optional Community Trap Trap check/deleteCheck and delete the trap address Public Trap option setting Up to 99,999 hours can be set for the time settingItem Auto Display setting and control page 3+p.123 Trap option Basic setting and operation Controlling the projector PJ temp Power control and status checkPJ status About projector condition Status Description Controls Input System Image adjustment Image mode Video Computer Suppresses the sound Adjusts the sound volume from the speakersSound PC adjustment Setting up the projector Screen mode VideoTable below Normal True Full Zoom Natural wide Custom Sets Auto PC Adjustment mode Sets Auto Keystone modeSets the auto-input signal detection mode Standby mode Lamp counter resetting Reset the time after lamp replaced Set a day or date Timer settingHow to set the timer Check the timer events Change the event modeSet an execute time Select an event action Projector Power Event Projector information Items Description Indication of the lamp status Status Example of multi control Controlling and setting the multi-projectorsMulti-control Menu are linked to the main menu Start/stop the multi controlStops multi control function Register the projector Confirmation of registered projector Status Change the mode of the registered projectorMode Operation Check & Change page in the light mode Setting all togetherCheck & Change page in the light mode Controlling all together Viewer auto setting all together Network capture functions About Network Capture function Start up the Network CaptureReal Time Capture +p.89 Network Communication +p.94 Commands on the task bar Menu during Real time capturingMenu during Network Communication Menu during Moderator function Parameter set up Using the Real Time Capture Registering the computers Control by the computer Time capturing operation Control by the web browserStart capturing of the PC1 from the PC5 Control by the projector Start capturing of the computer PC1 by using the projector Setting conditionExample of advanced use Start the presentation Using the Network Communication PC6 Settings before using the Network Communication Perform capture setting following to the description belowProjector can find up to 30 computers in the network Up to 30 computers can be registered to the projector Menu tree Description of capture editing window Command Tool Tool bar button namesBar of Sub PC Color tool bar Attribute tool bar How to use the Network communication Setting of the drawing tool attribute Edit capture imageDrawing figures Erase drawn objects Letter attribute setting 100Drawing letter Up to 1000 characters can be used for a letter frame Network Communication operation and change of state 101Preparation On the Communication Executing the forcing mode 102 Moderator function 103Projector Moderator Clients Preparation for using the moderator function Normal mode application windowModerator mode application window 104 Using the moderator function 105Description of application window Moderator operation 106 Moderators password setting upUnregister moderator status 107 Error informationError messages Cause and corresponding 108 Network viewer functions 109 How to use the Network Viewer 4 File Converter Creating the available data Network Viewer110 Start up and quit the File Converter Command Tool Button Creating the available data111 Menu Sub Menu Description View Network viewer functions Setting of output destination and conversion mode Conversion modeOutput destination 113 Select a folder and click Save button 115 Procedure of making programCreating a program file Program Editor List 116Program file Sub menu Description Setting up the display order and time of the images117 Red frame Shows that image is deleted from the folder Image frame on the index windowBlue frame This function is not available in the light mode Example of the created program selection119 Limitation of the Program file Using the Network Viewer function Select Network for input mode previously120 Condition to use the Network Viewer function 121 Setup the setting page 1 of the Visual displaySetup the setting page 2 of the Selection Display 122 Auto Display setting and control Error info123 Means endless play Error information Error type124 Description 125 Display time Repeat times 126 Appendix 127 When the word Hello is replied, login has been succeeded Password 1234 is used for the exampleUse of telnet 128 Command Function 129 Web browser setting Active Script/JavaScript enableFlash Player enable Proxy setting ActiveX controls and plug-ins setting Windows XP Professional131 Examples OS/Browsers Flash Player Add-on setting Using proxy serverNot using proxy server 132 Netscape Navigator Flash Player Plug-in setting133 134 Firewall setting Click OK to close setting135 On recommended Checked Dont allow exceptions Unchecked Troubleshooting 136 Cannot start up the browser Infrastructure Mode137 138 Cannot be turned on/off with the web browser 139 Speed of playing back images are very slow Microsoft power point format .ppt 140Images from the file server don’t appear on the screen? Cannot make a new program file 141 Terminology 142 143 Deutschland & Österreich