Manuals / EMC / Computer Equipment / Network Card

EMC QLA22xx, QLA23xx Configuring an EMC Boot Device, Configuring a CLARiiON Boot Device, 3-11

Models: QLA22xx QLA23xx

1 78

Download 78 pages 24.56 Kb

Page 43

Configuring a CLARiiON Boot Device

Start

Requirements

Satisfied

Prepare Storage

System

Boot LUN and Storage Group exist

Create HBA

Driver Diskettes

Gather Data

and Set Up

HBA BIOS

Configuring an EMC Boot Device

Unsatisfied

Complete

Requirements

Need boot LUN and Storage Group

Create boot LUN and

Storage Group

Need to update firmware and NVRAM

Update firmware

Need to update

NVRAM only

Update NVRAM

3

By WWPN				By Port Number
			Prepare Switch
Soft Zoning			Prepare Switch		Hard Zoning
Soft Zoning			Fabric		Hard Zoning
			Fabric					Install Additional Software


			Prepare Server
			Prepare Server

Configure HBA Boot BIOS

Install Windows

Verify Driver Installation

A

	A
Multiple HBA		Single HBA
PowerPath/ATF	Failover Software	PowerPath/CDE

Navisphere Agent

Configuring a CLARiiON Boot Device	3-11

Image 43

EMC QLA22xx, QLA23xx manual Configuring an EMC Boot Device, Configuring a CLARiiON Boot Device, 3-11

Contents

Hopkinton, MA 01748 P/N REV A01 AUGUSTEMC Corporation Corporate HeadquartersTrademark Information Copyright 2001-2003 EMC Corporation. All rights reservedEMC Fibre Channel with QLogic HBAs in Windows Hosts Introduction ContentsInstalling and Configuring the HBA Driver ChapterContents Configuring an EMC Boot DeviceChapter Appendix A Third-Party Software Appendix B TroubleshootingEMC Fibre Channel with QLogic HBAs in Windows Hosts ContentsA caution contains information essential to avoid data loss or PrefaceEMC uses the following conventions for notes, cautions, and warningsPalatino EMC Navisphere Manager 5.X Administrator’s Guide, P/NEMC Navisphere Manager 6.X Administrator’s Guide, P/N PowerPath Installation And Administration Guide for Windows, P/NIntroduction IntroductionIntroduction Understanding Persistent Binding in a Fabric EnvironmentUnderstanding Persistent Binding in a Fabric Environment PHYSICALDRIVE0 PHYSICALDRIVE4 PHYSICALDRIVE0 PHYSICALDRIVE4 PHYSICALDRIVE8Installing and Configuring the HBA Driver Installing and Configuring the HBA DriverDownloading QLogic Drivers and Firmware Verifying and Downloading the IntroductionDocumentation Installing an HBA 5. After connecting all HBAs in the server, power up the server 1. Remove the HBA from the server as instructed by your server guide 4. Select Host Adapter Settings from the Configuration Settings menu 7. Enter a value for the loop ID and press ENTER Advanced Adapter Settings , and Extended Firmware Settings EMC HBA SettingsPre-Configured SettingsSetting the Topology for QLA22xx/23xx and Windows on page Configuring NVRAM for Stratus ftServersUpdating Firmware/BIOS and Applying NVRAM Settings on page Manually Setting the HBA Data Rate on pageQLogic HBAs Firmware/BIOS andFibre-Down Servers with EmbeddedDo not attempt to run this procedure from a command prompt window 5. Select Extended Firmware Settings 3. Select host adapter 4. Select Configuration Settings5. Select Connection Options and press ENTER Install this patch before installing the HBA driver Installing the HBA DriverDriver Revision History Where to Find the Driver Windows 2003 STORPort Updates5. Select HAVE DISK Installation Procedure for Windows NT HostsInstallation Procedure for Windows 2000 and Windows 2003 Hosts Administrative Tools, Computer Management9. Click Have Disk 8. Select SCSI and RAID Controllers, then click Next4. Double-click the SCSI & RAID Controllers icon Updating the HBA Driver in a Windows 2000 or Windows 2003 Host12. If prompted, click Yes to continue the installation Upgrading to Windows 2003 from Windows 2000 or Windows NT 2-20 Installing and Configuring the HBA DriverEMC Fibre Channel with QLogic HBAs in Windows Hosts Configuring an EMC Boot Device Configuring an EMC Boot DeviceLost connection to array pulled or damaged cable connection IntroductionHow to Determine I/O Latency and Load on the Boot LUN Save to Disk Boot CrashdumpBehavior CTRL-Q for the HBA you wish to configure Configuring a Symmetrix Boot DeviceDifferent HBA models may display different banners. Be sure to select From the Selectable Boot Settings menu, select Selectable Boot From the Configuration Settings menu, select Host AdapterFrom the Host Adapter Settings menu, select Host Adapter From the Configuration Settings menu, select Selectable Bootthe Boot Device Installing theWindows OS onto From this point, press S to specify additional devices 1. Note these prerequisites RDP server with release Procedure Configuring a CLARiiON Boot DeviceFlowchart Configuring a CLARiiON Boot Device Configuring an EMC Boot Device3-11 Refer to the EMC Support Matrix RequirementsRefer to Downloading QLogic Drivers and Firmware on page Preparing the Storage System4. Select Host Adapter Settings and enable Host Adapter BIOS 3. Select Configuration Settings from the menu6. Select Selectable Boot Settings and enable Selectable Boot Device 9. Press ESC to exit the Fast!UTIL Options menu 10. Reboot the host c. Select Configuration Settings from the menu Node Name Continue to Preparing the Server Preparing the Server1. Select Set Boot Controller Order Boot BIOS Configuring the HBA4. Select Selectable Boot Settings from the Configuration Settings 9. Select Configuration Settings from the menu You need the following materials to install Windows The Windows Licensing Agreement appears HP ProLiant BL20p G2 Windows 2000 OS Installation Verifying HBA Driver and Digital Signature Installation Installing Multipath and Failover Software Assigning a Permanent Boot Drive Letter for Windows NTNavisphere Host Installing AdditionalConfiguring Additional Boot Port3. Select Configuration Settings from the menu With ATF configurations b. On the Computer Management window, click Disk Management Remove any old boot zoning from the previous installation Starting a Fresh Installation4. Reboot the server To start a fresh installation Using Manager, unbind the old boot LUNBoot Time and LUN Availability Follow the procedure under Configuring a Symmetrix Boot Device Replacing a Boot HBAEMC Symmetrix EMC CLARiiON How a Server Responds to Failure in the Boot LUN Path Known Issues 3-36 Configuring an EMC Boot DeviceEMC Fibre Channel with QLogic HBAs in Windows Hosts Third-Party Software Third-Party SoftwareQLogic SANSurfer SANBlade Manager After completing these changes, reboot the host system Veritas Volume Manager 3.x for WindowsUse regedt32.exe to set the registry as follows Third-Party Software EMC Fibre Channel with QLogic HBAs in Windows HostsTroubleshooting TroubleshootingProblem Problems and SolutionsProblem ProblemEMC Support. Windows 2003 driver 8.2.2.20 and later already ProblemEMC Fibre Channel with QLogic HBAs in Windows Hosts TroubleshootingIndex EMC Fibre Channel with QLogic HBAs in Windows Hosts Veritas Volume Manager 3.0 A-3Windows OS, installing onto a CLARiiON boot device zoning, hard 3-17 zoning, soft