Hopkinton, MA 01748
P/N REV A01 AUGUST
EMC Corporation
Corporate Headquarters
Copyright 2001-2003 EMC Corporation. All rights reserved
Trademark Information
EMC Fibre Channel with QLogic HBAs in Windows Hosts
Introduction
Contents
Installing and Configuring the HBA Driver
Chapter
Configuring an EMC Boot Device
Contents
Chapter
Appendix A Third-Party Software
Appendix B Troubleshooting
EMC Fibre Channel with QLogic HBAs in Windows Hosts
Contents
A caution contains information essential to avoid data loss or
Preface
EMC uses the following conventions for notes, cautions, and
warnings
Palatino
EMC Navisphere Manager 5.X Administrator’s Guide, P/N
EMC Navisphere Manager 6.X Administrator’s Guide, P/N
PowerPath Installation And Administration Guide for Windows, P/N
Introduction
Introduction
Introduction
Understanding Persistent Binding in a Fabric Environment
Understanding Persistent Binding in a Fabric Environment
PHYSICALDRIVE0 PHYSICALDRIVE4
PHYSICALDRIVE0 PHYSICALDRIVE4 PHYSICALDRIVE8
Installing and Configuring the HBA Driver
Installing and Configuring the HBA Driver
Introduction
Downloading QLogic Drivers and Firmware Verifying and Downloading the
Documentation
Installing an HBA
5. After connecting all HBAs in the server, power up the server
1. Remove the HBA from the server as instructed by your server guide
4. Select Host Adapter Settings from the Configuration Settings menu
7. Enter a value for the loop ID and press ENTER
Advanced Adapter Settings , and Extended Firmware Settings
EMC HBA Settings
Pre-Configured
Settings
Setting the Topology for QLA22xx/23xx and Windows on page
Configuring NVRAM for Stratus ftServers
Updating Firmware/BIOS and Applying NVRAM Settings on page
Manually Setting the HBA Data Rate on page
QLogic HBAs
Firmware/BIOS and
Fibre-Down Servers
with Embedded
Do not attempt to run this procedure from a command prompt window
5. Select Extended Firmware Settings
3. Select host adapter 4. Select Configuration Settings
5. Select Connection Options and press ENTER
Install this patch before installing the HBA driver
Installing the HBA Driver
Driver Revision History Where to Find the Driver
Windows 2003 STORPort Updates
5. Select HAVE DISK
Installation Procedure for Windows NT Hosts
Installation Procedure for Windows 2000 and Windows 2003 Hosts
Administrative Tools, Computer Management
9. Click Have Disk
8. Select SCSI and RAID Controllers, then click Next
4. Double-click the SCSI & RAID Controllers icon
Updating the HBA Driver in a Windows 2000 or Windows 2003 Host
12. If prompted, click Yes to continue the installation
Upgrading to Windows 2003 from Windows 2000 or Windows NT
Installing and Configuring the HBA Driver
2-20
EMC Fibre Channel with QLogic HBAs in Windows Hosts
Configuring an EMC Boot Device
Configuring an EMC Boot Device
Lost connection to array pulled or damaged cable connection
Introduction
How to Determine I/O Latency and Load on the Boot LUN
Boot Crashdump
Save to Disk
Behavior
Configuring a Symmetrix Boot Device
CTRL-Q for the HBA you wish to configure
Different HBA models may display different banners. Be sure to select
From the Selectable Boot Settings menu, select Selectable Boot
From the Configuration Settings menu, select Host Adapter
From the Host Adapter Settings menu, select Host Adapter
From the Configuration Settings menu, select Selectable Boot
Installing the
the Boot Device
Windows OS onto
From this point, press S to specify additional devices
1. Note these prerequisites RDP server with release
Configuring a CLARiiON Boot Device
Procedure
Flowchart
Configuring an EMC Boot Device
Configuring a CLARiiON Boot Device
3-11
Refer to the EMC Support Matrix
Requirements
Refer to Downloading QLogic Drivers and Firmware on page
Preparing the Storage System
3. Select Configuration Settings from the menu
4. Select Host Adapter Settings and enable Host Adapter BIOS
6. Select Selectable Boot Settings and enable Selectable Boot Device
9. Press ESC to exit the Fast!UTIL Options menu 10. Reboot the host
c. Select Configuration Settings from the menu
Node Name
Continue to Preparing the Server
Preparing the Server
1. Select Set Boot Controller Order
Configuring the HBA
Boot BIOS
4. Select Selectable Boot Settings from the Configuration Settings
9. Select Configuration Settings from the menu
You need the following materials to install Windows
The Windows Licensing Agreement appears
HP ProLiant BL20p G2 Windows 2000 OS Installation
Verifying HBA Driver and Digital Signature Installation
Installing Multipath and Failover Software
Assigning a Permanent Boot Drive Letter for Windows NT
Navisphere Host
Installing Additional
Configuring
Additional Boot Port
3. Select Configuration Settings from the menu
With ATF configurations
b. On the Computer Management window, click Disk Management
Remove any old boot zoning from the previous installation
Starting a Fresh Installation
4. Reboot the server To start a fresh installation
Using Manager, unbind the old boot LUN
Boot Time and LUN Availability
Replacing a Boot HBA
Follow the procedure under Configuring a Symmetrix Boot Device
EMC Symmetrix EMC CLARiiON
How a Server Responds to Failure in the Boot LUN Path
Known Issues
Configuring an EMC Boot Device
3-36
EMC Fibre Channel with QLogic HBAs in Windows Hosts
Third-Party Software
Third-Party Software
QLogic SANSurfer SANBlade Manager
Veritas Volume Manager 3.x for Windows
After completing these changes, reboot the host system
Use regedt32.exe to set the registry as follows
Third-Party Software
EMC Fibre Channel with QLogic HBAs in Windows Hosts
Troubleshooting
Troubleshooting
Problem
Problems and Solutions
Problem
Problem
EMC Support. Windows 2003 driver 8.2.2.20 and later already
Problem
EMC Fibre Channel with QLogic HBAs in Windows Hosts
Troubleshooting
Index
EMC Fibre Channel with QLogic HBAs in Windows Hosts
Veritas Volume Manager 3.0 A-3
Windows OS, installing onto a CLARiiON boot device
zoning, hard 3-17 zoning, soft