Manuals / Emerson / Computer Equipment / Computer Accessories

Emerson MVME2500 manual 2 Power Requirements, Hardware Preparation and Installation

Models: MVME2500

1 146

Download 146 pages 3.01 Kb

Page 28

Hardware Preparation and Installation

Product Damage

High humidity and condensation on the board surface causes short circuits.

Do not operate the board outside the specified environmental limits.

Make sure the board is completely dry and there is no moisture on any surface before applying power.

2.3.2Power Requirements

The board uses +5.0 V from the VMEbus backplane. On board power supply generates the required voltages for the various ICs. The MVME2500 connects the +12 V and -12 V supplies from the backplane to the PMC sites, while the +3.3 V power supplied to the PMC sites comes from the +5.0 V backplane power. A maximum of 10 A of +3.3 V power is available to the PMC sites, however the 90 W +5.0 V limit must be observed as well as any cooling limitations.

The following table provides an estimate of the typical and maximum power required.

Table 2-2 Power Requirements

Board Variant	Maximum (Calculated)	Typical (Measured Operating)

MVME2500-0163	18.5 W	14.8 W

MVME2500-0161	18.5 W	14.8 W

MVME2500-0173	24 W	16.6 W

MVME2500-0171	24 W	16.6 W

MVME2500ET-0173	24 W	16.6 W

MVME2500ET-0171	24 W	16.6 W

The power is measured when the board is in standby (Linux prompt). Power will significantly increase when adding hard drives or a XMC/PMC card.

28	MVME2500 Installation and Use (6806800L01H)

Image 28

Emerson MVME2500 manual 2 Power Requirements, Hardware Preparation and Installation

Contents

Installation and Use MVME2500P/N 6806800L01H January Embedded Computing for Business-Critical ContinuityTMLimited and Restricted Rights Legend TrademarksContact Address 2 Hardware Preparation and Installation Contents3 Controls, LEDs, and Connectors Contents Contents Contents 6 Boot System Contents Contents5 Memory Maps and Registers Contents B.1 Emerson Network Power - Embedded Computing DocumentsA Replacing the Battery 7 Programming ModelSafety Notes Sicherheitshinweise Index Contents ContentsMVME2500 Installation and Use 6806800L01H ListofTables List of Tables MVME2500 Installation and Use 6806800L01HList of Figures Figure A-1List of Figures MVME2500 Installation and Use 6806800L01HAbout this Manual Overview of ContentsAbbreviations About this Manual About this Manual Conventions About this ManualCourier + Bold ReferenceMVME2500 Installation and Use 6806800L01H About this Manual About this ManualNotation Description Logical ORSummary of Changes About this ManualThis manual has been revised and replaces all prior editions  Edited Figure Component Layout Updated Appendix B, Related  Updated Figure Component Layout onAbout this Manual About this Manual pageTable 1-1 Key Features of the MVME2500 IntroductionChapter 1.1 OverviewTable 1-1 Key Features of the MVME2500 continued Introduction1.2 Standard Compliances Table 1-2 Board Standard CompliancesTable 1-1 Key Features of the MVME2500 continued Introduction1.3 Mechanical Data 1.4 Ordering InformationTable 1-3 Mechanical Data Table 1-4 Available Board VariantsTable 1-5 Available Board Accessories Introduction1.5 Product Identification Figure 1-1 Serial Number LocationMVME2500 Installation and Use 6806800L01H Introduction2.1 Overview Hardware Preparation and InstallationChapter Hardware Preparation and Installation 2.2 Unpacking and Inspecting the Board2.3 Requirements Shipment InspectionTable 2-1 Environmental Requirements 2.3.1 Environmental RequirementsHardware Preparation and Installation Table 2-2 Power Requirements 2.3.2 Power RequirementsHardware Preparation and Installation 2.3.3 Equipment Requirements 2.4 Configuring the BoardHardware Preparation and Installation 2.5.1 Rear Transition Module 2.5 Installing AccessoriesHardware Preparation and Installation 2.5.2 PMC/XMC Support Installation ProcedureHardware Preparation and Installation 2.6 Installing and Removing the Board Hardware Preparation and InstallationHardware Preparation and Installation 2.7 Completing the Installation Hardware Preparation and InstallationControls, LEDs,and Connectors 3.1 Board LayoutFigure 3-1 Component Layout ChapterControls, LEDs, and Connectors Figure 3-2 Front Panel LEDs, Connectors and Switches3.2 Front Panel MVME2500 Installation and Use 6806800L01H3.2.1 Reset Switch 3.3 LEDs3.3.1 Front Panel LEDs Figure 3-3 Front Panel LEDsTable 3-1 Front Panel LEDs Controls, LEDs, and Connectors3.4 Connectors 3.3.2 Onboard LEDsTable 3-2 Onboard LEDs Status Controls, LEDs, and Connectors3.4.1 Front Panel Connectors Table 3-3 Front Panel Tri-Speed Ethernet Connector J13.4.1.1 RJ45 with Integrated Magnetics J1 Controls, LEDs, and ConnectorsTable 3-3 Front Panel Tri-Speed Ethernet Connector J1 continued 3.4.1.2 Front Panel Serial Port J4Table 3-4 Front Panel Serial Port J4 Controls, LEDs, and Connectors3.4.1.3 USB Connector J5 3.4.1.4 VMEBus P1 ConnectorTable 3-5 USB Connector J5 Table 3-6 VMEbus P1 ConnectorControls, LEDs, and Connectors Table 3-6 VMEbus P1 Connector continuedIRQ4 Table 3-7 VMEbus P2 Connector 3.4.1.5 VMEBus P2 ConnectorControls, LEDs, and Connectors 3.4.2 Onboard Connectors 3.4.2.1 Flash Program Connector P7Table 3-7 VMEbus P2 Connector continued Table 3-8 Flash Programming Header P73.4.2.2 SATA Connector J3 Table 3-9 Custom SATA Connector J3Table 3-8 Flash Programming Header P7 continued Controls, LEDs, and Connectors3.4.2.3 PMC Connectors Table 3-9 Custom SATA Connector J3 continuedTable 3-10 PMC J11 Connector Controls, LEDs, and ConnectorsTable 3-11 PMC J12 Connector Table 3-10 PMC J11 Connector continuedControls, LEDs, and Connectors Table 3-12 PMC J13 Connector Table 3-11 PMC J12 Connector continuedControls, LEDs, and Connectors Table 3-12 PMC J13 Connector continued Controls, LEDs, and ConnectorsControls, LEDs, and Connectors Table 3-13 PMC J14 ConnectorTable 3-12 PMC J13 Connector continued 3.4.2.4 JTAG Connector P6 Table 3-13 PMC J14 Connector continuedTable 3-14 JTAG Connector P6 Controls, LEDs, and ConnectorsTable 3-14 JTAG Connector P6 continued Controls, LEDs, and Connectors3.4.2.5 COP Connector P6 3.4.2.6 SD Connector J2Table 3-16 SD Connector J2 Table 3-15 COP Header P103.4.2.7 XMC Connector XJ2 Table 3-16 SD Connector J2 continuedTable 3-17 XMC Connector XJ2 Pinout Controls, LEDs, and Connectors3.4.2.8 Miscellaneous P2020 Debug Connectors Table 3-17 XMC Connector XJ2 Pinout continuedTable 3-18 P20x0 Debug Header Controls, LEDs, and Connectors3.5 Switches 3.5.1 Geographical Address Switch S1Table 3-18 P20x0 Debug Header continued Controls, LEDs, and ConnectorsTable 3-19 Geographical Address Switch Figure 3-5 Geographical Address SwitchControls, LEDs, and Connectors 3.5.2 SMT Configuration Switch S2 Figure 3-6 SMT Configuration Switch PositionTable 3-20 Geographical Address Switch Settings Controls, LEDs, and ConnectorsTable 3-20 Geographical Address Switch Settings continued Controls, LEDs, and Connectors4.1 Block Diagram Figure 4-1 Block DiagramFunctional Description 4.2 Chipset4.2.2 Integrated Memory Controller 4.2.1 e500 Processor CoreFunctional Description 4.2.3 PCI Express Interface 4.2.4 Local Bus Controller LBC4.2.5 Secure Digital Hub Controller SDHC 4.2.6 I2C Interface4.2.8 DUART 4.2.9 DMA Controller4.2.10 Enhanced Three-Speed Ethernet Controller eTSEC 4.2.11 General Purpose I/O GPIO4.4 Timers 4.2.14 P20x0 Hardware Configuration Pins4.3 System Memory 4.2.13 Common On-Chip Processor COP4.4.2 Internal Timer 4.4.3 Watchdog Timer4.4.4 FPGA Tick Timer 4.5 Ethernet Interfaces4.6 SPI Bus Interface 4.6.1 SPI Flash Memory4.6.2 SPI Flash Programming Functional Description4.6.3 Firmware Redundancy Functional DescriptionFigure 4-2 SPI Device Multiplexing Logic Functional Description4.7 Front UART Control 4.6.4 Crisis RecoveryFunctional Description 4.9 PMC/XMC Sites 4.8 Rear UART ControlFunctional Description 4.10 SATA Interface 4.9.1 PMC Add-on Card4.9.2 XMC Add-on Card Functional Description4.11 VME Support 4.12 USB4.13 I2C Devices 4.11.1 Tsi148 VME Controller4.14 Reset/Control FPGA 4.15 Power Management4.15.1 Onboard Voltage Supply Requirement Table 4-1 Voltage Supply RequirementFunctional Description 4.15.2 Power Up Sequencing RequirementsTable 4-1 Voltage Supply Requirement 4.17 Reset Structure Figure 4-3 Clock Distribution Diagram4.16 Clock Structure Functional Description4.19 Real-Time Clock Battery 4.17.1 Reset Sequence4.18 Thermal Management Table 4-2 Thermal Interrupt Threshold4.20.1 POST Code Indicator Table 4-3 POST Code Indicator on the LED4.20 Debugging Support 4.20.2 JTAG Chain and BoardTable 4-4 Transition Module Features 4.21 Rear Transition Module RTM4.20.3 Custom Debugging Functional DescriptionMVME2500 Installation and Use 6806800L01H Functional DescriptionMemory Maps and Registers 5.1 Overview5.2 Memory Map Table 5-1 Physical Address Map5.3 Flash Memory Map 5.4 Linux Devices Memory MapMemory Maps and Registers Table 5-2 Flash Memory MapTable 5-3 Linux Devices Memory Map Memory Maps and Registers8-bit field containing the current timer/register PLD revision. The 5.5 Programmable Logic Device PLD Registers5.5.1 PLD Revision Register 5.5.2 PLD Year Register5.5.3 PLD Month Register 5.5.4 PLD Day Register5.5.5 PLD Sequence Register Table 5-6 PLD Month Register5.5.6 PLD Power Good Monitor Register Table 5-9 PLD Power Good Monitor Register1.2V Supply power good indicator 1.8V Supply power good indicator5.5.7 PLD LED Control Register Table 5-10 PLD LED Control RegisterLEDs Status on page Memory Maps and Registers5.5.8 PLD PCI/PMC/XMC Monitor Register Table 5-11 PLD PCI/PMC/XMC Monitor RegisterMemory Maps and Registers Field Description5.5.9 PLD U-Boot and TSI Monitor Register 5.5.10 PLD Boot Bank RegisterTable 5-12 PLD U-Boot and TSI Monitor Register Table 5-13 PLD Boot Bank RegisterTable 5-13 PLD Boot Bank Register BOOTBLOCKABoot Block Manual Selector Switch Actual Boot Bank5.5.11 PLD Write Protect and I2C Debug Register Table 5-14 PLD Write Protect and I2C Debug RegisterMemory Maps and Registers Field DescriptionMemory Maps and Registers 5.5.12 PLD Test Register 5.5.13 PLD Test RegisterTable 5-15 PLD Test Register Table 5-16 PLD Test Register5.5.14 PLD GPIO2 Interrupt Register Table 5-17 PLD GPIO2 Interrupt RegisterMemory Maps and Registers Field Description5.5.15 PLD Shutdown and Reset Control and Reset Reason Register Table 5-18 PLD Shutdown and Reset Control and Reset Reason RegisterAUTOSHDNMASK Automatic Shutdown Mask5.5.16 PLD Watchdog Timer Refresh Register Table 5-19 PLD Watchdog Timer Refresh RegisterMemory Maps and Registers Field Description5.5.18 PLD Watchdog Timer Count Register Table 5-21 PLD Watchdog Timer Count Register5.5.17 PLD Watchdog Control Register Table 5-20 PLD Watchdog Control Register5.6 External Timer Registers 5.6.1 Prescaler RegisterTable 5-22 Prescaler Register Memory Maps and RegistersTable 5-23 Control Registers 5.6.2 Control RegistersMemory Maps and Registers 5.6.3 Compare High and Low Word Registers Table 5-24 Compare High Word RegistersTable 5-25 Compare Low Word Registers Memory Maps and Registers5.6.4 Counter High and Low Word Registers Table 5-26 Counter High Word RegistersTable 5-27 Counter Low Word Registers Memory Maps and RegistersMVME2500 Installation and Use 6806800L01H Memory Maps and RegistersBoot System 6.2 Accessing U-Boot6.1 Overview Chapter6.3 Boot Options 6.3.1 Booting from a NetworkBoot System setenv netmask netmask6.3.2 Booting from an Optional SATA Drive 6.3.3 Booting from a USB Drive# option usb - interface, 01 - device 0 partition Boot System6.3.4 Booting from an SD Card 6.3.5 Booting VxWorks Through the Network# option mmc - interface, 01 - device 0 partition Boot SystemBoot System 6.4 Using the Persistent Memory FeatureAnalyzing Kernel Log Files after a Kernel Panic Table 6-1 MVME2500 Specific U-Boot Commands 6.5 MVME2500 Specific U-Boot CommandsBoot System Table 6-1 MVME2500 Specific U-Boot Commands continued Boot SystemBoot System 6.6 Updating U-BootTable 6-1 MVME2500 Specific U-Boot Commands continued Boot System 4. Erase 0x90000 bytes starting at SPI address 0 sf erase 0Boot System MVME2500 Installation and Use 6806800L01H7.2 Reset Configuration Table 7-1 POR Configuration SettingsProgramming Model 7.1 OverviewTable 7-1 POR Configuration Settings continued Programming ModelTable 7-1 POR Configuration Settings continued mode either RTBI, RGMIoperates using the RGMII Programming ModelTable 7-1 POR Configuration Settings continued Programming ModelTable 7-2 MVME2500 Interrupt List 7.3 Interrupt ControllerProgramming Model 7.4 I2C Bus Device Addressing 7.5 Ethernet PHY AddressTable 7-3 I2C Bus Device Addressing Table 7-4 PHY Types and MII Management Bus Address7.6 Other Software Considerations 7.6.1 MRAM7.6.2 Real Time Clock 7.6.3 Quad UART7.6.4 LBC Timing Parameters Table 7-5 LBC Timing ParametersProgramming Model Field DescriptionTable 7-6 Clock Distribution 7.7 Clock DistributionProgramming Model 7.7.1 System Clock Table 7-6 Clock Distribution continuedTable 7-7 System Clock Programming Model7.7.3 Local Bus Controller Clock Divisor 7.7.2 Real Time Clock InputProgramming Model MVME2500 Installation and Use 6806800L01H Programming ModelReplacing the Battery A.1 Replacing the BatteryFigure A-1 Battery Location Appendix AReplacing the Battery Replacing the Battery Replacement ProcedureTo replace the battery, proceed as follows 1. Remove the old battery 2. Install the new battery with the plus sign + facing upReplacing the Battery MVME2500 Installation and Use 6806800L01HB.1 Emerson Network Power - Embedded Computing Documents Table B-1 Emerson Network Power - Embedded Computing PublicationsRelated Documentation Appendix BB.3 Related Specifications Table B-3 Related SpecificationsB.2 Manufacturers’ Documents Related DocumentationTable B-3 Related Specifications PCI-X Protocol Addendum to the PCI Local Bus Specification PCI-X PTRelated Documentation IEEE Standard for a Common Mezzanine Card CMC Family IEEE StdMVME2500 Installation and Use 6806800L01H Related DocumentationSafety Notes EMC Results pending testingSafety Notes InstallationOperation Cabling and Connectors Safety NotesBattery Safety NotesSicherheitshinweise Betrieb SicherheitshinweiseSicherheitshinweise InstallationBeschädigung von Schaltkreisen Kabel und Stecker BatterieSicherheitshinweise Bei Fragen wenden Sie sich an Ihren SystemverwalterUmweltschutz SicherheitshinweiseMVME2500 Installation and Use 6806800L01H SicherheitshinweiseIndex Index MVME2500 Installation and Use 6806800L01HPage HOW TO REACH LITERATURE AND TECHNICAL SUPPORT