Hardware Preparation and Installation | Emerson MVME2500 specs

Hardware Preparation and Installation

Damage of Circuits

Electrostatic discharge and incorrect installation and removal can damage circuits or shorten its life.

Before touching the board or electronic components, make sure that you are working in an ESD-safe environment.

Product Damage

Only use injector handles for board insertion to avoid damage to the front panel and/or PCB. Deformation of the front panel can cause an electrical short or other board malfunction.

1.Attach an ESD strap to your wrist. Attach the other end of the strap to an electrical ground. Make sure that it is securely fastened throughout the procedure.

2.Remove VME filler panels from the VME enclosures, as appropriate.

3.Install the top and bottom edge of the board into the guides of the chassis.

4.Ensure that the levers of the two injector/ejectors are in the outward position.

5.Slide the board into the chassis until resistance is felt.

6.Simultaneously move the injector/ejector levers in an inward direction.

7.Verify that the board is properly seated and secure it to the chassis using the two screws located adjacent to the injector/ejector levers.

8.Connect the appropriate cables to the board.

To remove the board from the chassis, reverse the procedure and press the red locking tabs (IEEE handles only) to extract the board.

MVME2500 Installation and Use (6806800L01H)

33

Image 33

Emerson MVME2500 manual Hardware Preparation and Installation

Contents

MVME2500 Contact Address Contents Contents Contents Memory Maps and Registers Emerson Network Power Embedded Computing Documents Safety Notes Sicherheitshinweise Index List of Tables List of Tables Figure A-1 List of Figures List of Figures Overview of Contents About this ManualAbbreviations About this Manual USB ConventionsVita VME About this Manual About this Manual Summary of Changes Documentation, on Key Features of the MVME2500 IntroductionOverview Introduction KB Mram 8 KB VPD Eeprom Board Standard Compliances Standard Compliances Ordering Information Mechanical DataMechanical Data Available Board Variants VME-HDMNTKIT Available Board AccessoriesVME-64GBSSDKIT SERIAL-MINI-D Serial Number Location Product Identification Hardware Preparation and Installation Hardware Preparation and Installation Unpacking and Inspecting the BoardRequirements Environmental Requirements Environmental RequirementsGrms Power Requirements Power Requirements Equipment Requirements Configuring the Board Rear Transition Module Installing Accessories 2 PMC/XMC Support Installation Procedure Installing and Removing the Board Hardware Preparation and Installation Completing the Installation Board Layout Controls, LEDs, and Connectors Front Panel Controls, LEDs, and Connectors Reset Switch LEDsFront Panel LEDs Fail UserGENET1 TSEC1 Speed Connectors Onboard LEDsOnboard LEDs Status Front Panel Connectors Front Panel Tri-Speed Ethernet Connector J11.1 RJ45 with Integrated Magnetics J1 Front Panel Serial Port J4 Front Panel Serial Port J4 VMEBus P1 Connector Controls, LEDs, and Connectors USB Connector J5USB Connector J5 VMEbus P1 Connector GND BR3 DS0 BR1 Lword GA2 Write BR2GA3 Dtack GA4 VMEbus P2 Connector Controls, LEDs, and Connectors VMEBus P2 Connector Onboard Connectors Flash Program Connector P7Flash Programming Header P7 Custom Sata Connector J3 Sata Connector J3GND Sata Power Enable Sata TX + Sata Detect Sata RX 10 PMC J11 Connector PMC Connectors 11 PMC J12 Connector 12 PMC J13 Connector PAR64 GND CBE7 CBE6 CBE5 CBE4 13 PMC J14 Connector 14 Jtag Connector P6 Jtag Connector P6 GND Scan 2 TDI Scan 3 TMS Scan 3 TCK1 Scan 3 TDO GPO0 Scan 2 TMS Scan 2 TDO Scan 2 TCKScan 3 TCK GND Scan 4 TDI Scan 4 TCK Scan 4 Trst Scan 5 TMS Scan 5 TDO SD Connector J2 Controls, LEDs, and Connectors COP Connector P616 SD Connector J2 15 COP Header P10 17 XMC Connector XJ2 Pinout XMC Connector XJ2 18 P20x0 Debug Header Miscellaneous P2020 Debug Connectors Switches Geographical Address Switch S1Trigin MSRCID4 GND GAP4 VME Scon SEL2GAP3 GAP2 SMT Configuration Switch S2 Bled MasterwpdisaGbemuxsel Plane Block Diagram Functional DescriptionChipset 1 e500 Processor Core Integrated Memory ControllerFunctional Description Local Bus Controller LBC PCI Express InterfaceSecure Digital Hub Controller Sdhc 6 I2C Interface DMA Controller DuartEnhanced Three-Speed Ethernet Controller eTSEC General Purpose I/O Gpio 14 P20x0 Hardware Configuration Pins TimersSystem Memory Common On-Chip Processor COP Watchdog Timer Internal TimerFpga Tick Timer Ethernet Interfaces SPI Bus Interface SPI Flash MemorySPI Flash Programming Firmware Redundancy SPI Device Multiplexing Logic Front Uart Control Crisis Recovery PMC/XMC Sites Rear Uart Control Sata Interface PMC Add-on CardXMC Add-on Card 12 USB VME Support13 I2C Devices 11.1 Tsi148 VME Controller Power Management Reset/Control FpgaOnboard Voltage Supply Requirement Voltage Supply Requirement Power Up Sequencing Requirements Clock Structure Reset Structure Reset Sequence Real-Time Clock BatteryThermal Management Thermal Interrupt Threshold Post Code Indicator on the LED Post Code IndicatorDebugging Support Jtag Chain and Board Rear Transition Module RTM Transition Module FeaturesCustom Debugging SBC Functional Description Memory Maps and Registers Memory MapPhysical Address Map Linux Devices Memory Map Flash Memory MapMemory Maps and Registers Flash Memory Map Linux Devices Memory Map PLD Revision Register Programmable Logic Device PLD RegistersPLD Year Register PLD Revision Register PLD Month Register PLD Day RegisterPLD Sequence Register PLD Power Good Monitor Register PLD Power Good Monitor RegisterWrgd RGD Pwrg Oper Reset Rsvd Pwrv PLD LED Control Register 10 PLD LED Control RegisterPWRV1P2SWPWRG PLD PCI/PMC/XMC Monitor Register 11 PLD PCI/PMC/XMC Monitor RegisterPMC1PN PLD Boot Bank Register PLD U-Boot and TSI Monitor Register12 PLD U-Boot and TSI Monitor Register 13 PLD Boot Bank Register Locka Bootb Boots PLD Write Protect and I2C Debug Register Wpdi WPN Ugen Flash Sabled Oper Reset14 PLD Write Protect and I2C Debug Register Rsvd Master Flash I2CDEB Serial I2CDEBUGEN=0 PLD Test Register 15 PLD Test Register16 PLD Test Register Rsvd NMI TICK0INT TICK1INT TICK2INT Oper Reset PLD GPIO2 Interrupt Register17 PLD GPIO2 Interrupt Register 18 PLD Shutdown and Reset Control and Reset Reason Register PLD Shutdown and Reset Control and Reset Reason RegisterCpureset Wdtime Lrsto Dnmask OUT Oper Reset 19 PLD Watchdog Timer Refresh Register PLD Watchdog Timer Refresh Register 21 PLD Watchdog Timer Count Register PLD Watchdog Timer Count RegisterPLD Watchdog Control Register 20 PLD Watchdog Control Register External Timer Registers Prescaler Register22 Prescaler Register Control Registers COC ENC Oper Reset23 Control Registers Ints Cint Compare High and Low Word Registers 24 Compare High Word Registers25 Compare Low Word Registers Counter High and Low Word Registers 26 Counter High Word Registers27 Counter Low Word Registers 102 Accessing U-Boot Boot System Boot Options Booting from a NetworkBoot System Booting from a USB Drive Booting from an Optional Sata Drive Booting VxWorks Through the Network Booting from an SD Card Analyzing Kernel Log Files after a Kernel Panic Using the Persistent Memory Feature MVME2500 Specific U-Boot Commands MVME2500 Specific U-Boot Commands Boot System Updating U-Boot Sf probe 112 Reset Configuration POR Configuration SettingsProgramming Model Programming Model ETSEC3 Sgmmi TSEC1588ALARM Config Config Pins Selection Remarks ETSEC2 Sgmii LGPL1Ecmdc ETSEC1 TSEC1TXD0 TSEC1TXER Config Config Pins Selection Remarks Boot ROMLWE1/LBS1 TSEC2TXER MVME2500 Interrupt List Interrupt Controller Ethernet PHY Address I2C Bus Device AddressingI2C Bus Device Addressing PHY Types and MII Management Bus Address Mram Other Software ConsiderationsQuad Uart TSEC3 LBC Timing Parameters LBC Timing Parameters Clock Distribution Clock Distribution System Clock System Clock Local Bus Controller Clock Divisor Real Time Clock Input 124 Replacing the Battery Replacing the Battery Replacing the Battery Replacement Procedure 128 Related Documentation Emerson Network Power Embedded Computing Documents Table B-3 Related Specifications Related SpecificationsManufacturers’ Documents Related Documentation SATA-IO PCI-SIG 132 EMC Results pending testing Safety Notes Installation Safety NotesOperation Cabling and Connectors Battery Sicherheitshinweise Sicherheitshinweise Betrieb 139 Batterie Kabel und Stecker Umweltschutz 142 Index Index Page HOW to Reach Literature and Technical Support