Extron electronic manual Preliminary, Input Configuration menu flow, MGP 464 Operation

Input Configuration menu

The Input Configuration menu allows you to select a video signal type for each of the four fully configurable inputs. All of these inputs can accept the following video signals: RGB, YUV-HD, YUVi, RGBcvS, S-video, composite video, and DVI (MGP 464 DI only); RGB is the default. You can also select the horizontal and vertical start positions, pixel sampling phase for the four windows (except for YUVi, S-video, and composite video inputs), total pixels, active pixels, and active lines for each input. Rotate the horizontal Adjust ([) knob to cycle through the four inputs, and the vertical Adjust knob ({) to adjust the setting.

NThe 15 virtual inputs (numbered 5 through 19) cannot be configured from the front panel; you must use SIS commands, the Windows-based control software, or the MGP 464 Web pages.

Auto

Image

Menu

Input

Configuration

Next

Input #1

RGB

Next

Input #1 Film Mode ON

Next

Input #1 Vert Start 0128

Next

	Input #1	Next		Input #1
Horz Start 0128			PxPhs Win#1 16

PRELIMINARY

Input Input video type

•Input #1 Select a signal format:

• Input #2		• RGB
•	Input #3	• YUV-HD
•	Input #4	• RGBcvS
		•	YUVi
		•	S-video

• Composite

• DVI (MGP 464DI only)

Next

	Input #1	Next
Active Lns 1024

Input		Film Mode	Input		Vertical Start
•	Input #1	Turn Film Mode on	•	Input #1	Select a vertical
•	Input #2	or off (for low-	•	Input #2	start line position
•	Input #3	resolution devices).	•	Input #3	for the top edge of
•	Input #4		•	Input #4	the active video.

	Input #1	Next		Input #1	Next
Active Pxl 1280			Total Pxl 1688

Input		Horizontal Start	Input		Pixel Phase 1 Next
•	Input #1	Select a horizontal	•	Input #1	Adjust the pixel
•	Input #2	start pixel position	•	Input #2	sampling point
•	Input #3	for the left edge of	•	Input #3	for window 1 for
•	Input #4	the active video.	•	Input #4	each input.

Input #1

PxPhs Win#2 16

			Input			Pixel Phase 2
							Next
			•	Input #1		Adjust the pixel
			•	Input #2		sampling point
			•	Input #3		for window 2 for
			•	Input #4		each input.
	Input #1	Next			Input #1
PxPhs Win#4 16				PxPhs Win#3 16

Input		Active Lines	Input		Active Pixels	Input		Total Pixels
•	Input #1	Specify the height	•	Input #1	Specify the width	•	Input #1	Specify the width in
•	Input #2	in lines of the	•	Input #2	in pixels of the	•	Input #2	pixels of the total
•	Input #3	active image area	•	Input #3	active image area	•	Input #3	image area to be
•	Input #4	to be sampled.	•	Input #4	to be sampled.	•	Input #4	sampled.

Input		Pixel Phase 4	Input		Pixel Phase 3
•	Input #1	Adjust the pixel	•	Input #1	Adjust the pixel
•	Input #2	sampling point for	•	Input #2	sampling point for
•	Input #3	window 4 for each	•	Input #3	window 3 for each
•	Input #4	input.	•	Input #4	input.

Input Configuration menu flow

MGP 464 • Operation 3-9