Enter File Name image.out | Fortinet 50A/50B, 100 guide


FortiGate Firmware	Installing and using a backup firmware image

9Type an IP address that can be used by the FortiGate unit to connect to the FTP server.

The IP address can be any IP address that is valid for the network the interface is connected to. Make sure you do not enter the IP address of another device on this network.

The following message appears:

Enter File Name [image.out]:

10Enter the firmware image file name and press Enter.

The TFTP server uploads the firmware image file to the FortiGate unit and the following message is displayed.

Save as Default firmware/Backup firmware/Run image without saving:[D/B/R]

11Type B.

The FortiGate unit saves the backup firmware image and restarts. When the FortiGate unit restarts it is running the previously installed firmware version.

FortiGate-50A/50B, FortiWiFi-50B and FortiGate-100 FortiOS 3.0 MR4 Install Guide	79
01-30004-0265-20070831

Image 79

Fortinet 50A/50B, 100 manual Enter File Name image.out

Contents

Install G U I D E Regulatory compliance Trademarks Contents Configuring the FortiGate unit Factory defaults Using a wireless network Configuring the modem interfaceFortiGate Firmware Reverting to a previous firmware version IndexFortiUSB key About the FortiGate unit IntroductionFortiGate-50A Register your FortiGate unit FortiWiFi-50BFortiGate-50B FortiGate-100 FortiMail FortiGuard Subscription ServicesFortinet Family Products FortiClient FortiBridge About this documentFortiAnalyzer FortiReporter Typographic conventions Document conventions Fortinet documentation Comments on Fortinet technical documentation Customer service and technical supportFortinet Tools and Documentation CD Fortinet Knowledge Center Customer service and technical support Package Contents Installing the FortiGate unit Specifications Technical Specifications DimensionsWeight Power Requirements FortiWiFi-50B package contents Back FortiGate-100 package contents Front To power on the FortiGate unit Powering on the FortiGate unitMounting Power over Ethernet Connecting to the web-based manager Powering off the FortiGate unitConnecting to the FortiGate unit Command line interface To connect to the web-based manager FortiGate login Stop bits Flow control Connecting to the CLITo connect to the CLI Bits per second 9600 Data bits Parity Quick configuration using default settings Quick installation using factory defaults Go to System Network Options Quick installation using factory defaults Factory defaults Factory default NAT/Route mode network configuration Factory default Dhcp server configuration Management IP Factory default Transparent mode network configurationFactory default firewall configuration Administrative access Factory default protection profiles To reset the default settings Go to System Status Restoring the default settingsRestoring the default settings using the web-based manager Restoring the default settings using the CLI Restoring the default settings Planning the FortiGate configuration Configuring the FortiGate unitNAT/Route mode Internet Router NAT/Route mode with multiple external network connections Transparent mode Go to System Network Interface NAT/Route mode installationPreparing to configure the FortiGate unit in NAT/Route mode NAT/Route mode settings Using the web-based manager Dhcp or PPPoE configurationConfiguring basic settings To configure interfaces Go to System Network Interface Adding a default routeTo add a default route Go to Router Static Verify the connection Verifying the web-based manager configurationUsing the command line interface Configuring the FortiGate unit to operate in NAT/Route mode To set the external interface to use PPPoE, enter To configure DNS server settingsExample To set the external interface to use DHCP, enter To add a default route Configuring the networks Connecting the FortiGate unit to the networksTo connect the FortiGate unit DNS Settings Transparent mode installationPreparing to configure Transparent mode Transparent mode settings Administrator Password To verify the DNS server settings To change to Transparent mode using the CLI Connecting the FortiGate unit to your network Reconnecting to the web-based managerTo connect the FortiGate unit running in Transparent mode Set the date and time Next steps Updating antivirus and IPS signatures Updating the IPS signatures from the CLI Scheduling antivirus and IPS updatesTo update IPS signatures using the CLI To enable schedule updates from the CLI Adding an override server To add an override server using the CLI Next steps Connecting a modem to the FortiGate-50A Configuring the modem interface Redundant mode configuration Selecting a modem modeStand alone mode configuration Mode must be standalone Interface name Configuring the modem for the FortiGate-50A Phone-number CLI commands for the FortiGate-50A Dead gateway detection Adding a Ping Server Adding firewall policies for modem connections Setting up a wireless network Using a wireless network Radio Frequency interface Positioning an Access Point Using multiple APs to provide a constant strong signal Using multiple access points Wireless Equivalent Privacy WEP Wireless SecurityWi-Fi Protected Access WPA Additional security measures FortiWiFi-50B operation modesService Set Identifier Access Point mode FortiWiFi in Access Point mode Client mode Changing the operating mode Setting up the FortiWiFi-50B as an Access PointSet the Dhcp settings To set the data security Go to System Wireless Settings Configure the firewall policiesSet the security options Upgrading to a new firmware version Upgrading the firmware using the web-based managerTo upgrade the firmware using the web-based manager FortiGate Firmware To upgrade the firmware using the CLI Upgrading the firmware using the CLI Reverting to a previous firmware version For information, see the FortiGate Administration Guide To revert to a previous firmware version using the CLI Reverting to a previous firmware version using the CLI Execute ping To install firmware from a system reboot Press Any Key To Download Boot Image Restoring the previous configuration To backup configuration using the CLI Backup and Restore from the FortiUSB keyFortiUSB key To restore configuration using the CLI Using the USB Auto-Install featureTo configure the USB Auto-Install using the CLI Additional CLI commands for the FortiUSB key Testing a new firmware image before installing itTo test a new firmware image Testing a new firmware image before installing it Installing a backup firmware image Installing and using a backup firmware image Press any key to enter configuration menu To install a backup firmware image Enter File Name image.out Installing and using a backup firmware image CLI Index Wall mounting Web-based manager, connecting