Manuals / Frymaster / Kitchen Appliance / Fryer

Frymaster H14 Series Troubleshooting Fryers Equipped with Analog Controllers, Fryer Off

Models: H14 Series

1 110

Download 110 pages 58.94 Kb

Page 46

6.2.2 Troubleshooting Fryers Equipped with Analog Controllers

6.2.2 Troubleshooting Fryers Equipped with Analog Controllers

Fryer Off

CONTROLLER

PANEL OPEN

INTERFACE

BOARD VISIBLE

Press the ON/

OFF switch (OFF

displayed in

window).

Is the CMP LED in the top center of the interface board illuminated?

NO

Probable causes are:

1.No power applied to the fryer power cord

2.Defective 12-volt transformer

3.Defective interface board

4.Broken or improper wire connection

YES

Is the 24V LED on the		NO
interface board
illuminated?
	YES

Is the AL LED illuminated?	NO

Probable causes are:

1. Defective 24-volt transformer

2.Defective interface board

3.Broken or improper wire connection

Probable causes are:

1. Defective interface board

YES

Condition normal.

6-6

Image 46

Frymaster H14 Series Troubleshooting Fryers Equipped with Analog Controllers, Fryer Off, Is the AL LED illuminated?

Contents

MANUFACTURED BY FRYMASTER CORPORATION P.O. BOX SHREVEPORT, LOUISIANA SERVICE MANUAL FRYMASTER H14 SERIES ELECTRIC FRYERPHONE TOLL FREE 1-800-24 FRYER FAX COMPUTERS FCC CANADAB. WARRANTY PROVISIONS - FRYPOTS WARRANTY STATEMENTA. WARRANTY PROVISIONS - FRYERS D. WARRANTY PROVISIONS - COOKING COMPUTERF. WARRANTY EXCLUSIONS E. PARTS RETURNExample of a CAUTION box 1.2 Safety InformationCHAPTER 1 INTRODUCTION 1.1 General Example of a WARNING boxCE Standard Example of box used to distinguish CE and 1.3 Computer Information1.4 European Community CE Specific Information Non-CE specific informationRETAIN AND STORE THIS MANUAL IN A SAFE PLACE FOR FUTURE USE 1.5 Shipping Damage Claim Procedure1.6 Service Information What to do if your equipment arrives damagedconnections DANGER CHAPTER 2 INSTALLATION INSTRUCTIONS 2.1 GeneralCopper wire suitable for at least 167 F 75 C MUST be used for power this or any other applianceDANGER 2.3 Power Requirements2.2 After Fryers Are Under The Fry Station Hood DANGER2.4 Frypot Boil-Out CHAPTER 3 OPERATING FRYERS WITH M100B COOKING COMPUTERS 3.1 Equipment Setup and Shutdown ProceduresSetup 3.2 Introduction To The M-100B Cooking ComputerDESCRIPTION properly filled with vegetable oil. See Section 3.3 M-100B Computer Operating InstructionsOperating the Computer on Full-Vat Fryers Operating the Computer on Split-Vat Fryers Viewing the Frypot Temperature Actual or SetpointCooking Product Full-Vat or Split-Vat Open Drain Valve Indication 3.4 M-100B Computer Problem Condition IndicatorsLow Temperature Indication Probe Failure IndicationRecovery Out of Range REC LOC How to Enter the Setup Mode 3.5.1 M-100B Computer Setup Mode3.5 M-100B Computer Set-Up and Programming Instructions How to Configure the Computer for Use on an Electric Fryer How to Change the Computer’s Display LanguageHow to Change Computer Product/Temperature Displays How to Calibrate Computer Temperature to Actual Frypot Temperature How to Activate or Deactivate the Frypot BOIL-OUT FeatureHow to Change the Shake, Pull, Or Quality Times for Menu Items How to Enter the Program ModeHow to Reset the Computer to the Factory Defaults 3.5.2 M-100B Computer Programming ModeHow to Change the Cooking Temperature Setpoint How to Enter a Product Name in a Test MenuPage How to Suppress a Shake, QA, or Duty Function How to Turn the Display of a Factory-Programmed Menu Item On and OffHow to Display the Product Cycle Accumulator Information How to Display “Use Time” InformationHow to Use the Filter Countdown Timer CHAPTER 4 OPERATING FRYERS WITH ANALOG CONTROLLERS 4.1 Equipment Setup and Shutdown Proceduresswitch to the ON position. Failure to do so could damage the frypot 4.2 Introduction to the Analog ControllerDESCRIPTION A B C D E F G H I J K L M N4.4 Analog Controller High-Limit Check control-check procedure4.3 Analog Controller Operating Instructions Tools needed Maple Paddlerelease switch DESCRIPTION CHAPTER 5 OPERATING THE BUILT-IN FILTRATION SYSTEMFUNCTION Switch computer to OFF Slide the filter pan from the fryer cabinet 8.1 STEP-BY-STEP FILTRATION INSTRUCTIONSOpen the filter-cover, and remove and clean the crumb tray Remove and clean the filter screen WARNING Do Not Use Filter Powder on Filter Pads Slide the filter pan back inside fryer cabinet With fryer off, open drain valve Return handle and drain-valve handle locationTurn the computer back ON and use right The computer will countdown the process, although it does not control the filtering With the drain-valve closed, frypot fills with oil Close the drain-valve and leave the filter pump on to fill the frypotTurn off filter pump Top up oil level. Some oil may be lost in filtering process Turn the filter alarm off by pressingFill to first mark in frypot 8.2 CARE AND CLEANING OF YOUR FRYER AND FILTER SYSTEM WATER IN THE FILTER PAN MSDU50 6.2 Troubleshooting CHAPTER 6 PREVENTIVE MAINTENANCE AND TROUBLESHOOTING6.1 Preventive Maintenance Verify that electrical cords are securely plugged in6.2.1 Troubleshooting Fryers Equipped with M100B Computers Fryer OffFryer Heating Oil CONTINUED FROM PRECEEDING PAGE Is the right HI LED lit for split vat CONTINUED FROM PRECEEDING PAGE Do elements heat and draw proper amps? Fryer Off 6.2.2 Troubleshooting Fryers Equipped with Analog ControllersIs the AL LED illuminated? Fryer Heating Oil CONTINUED FROM PRECEEDING PAGE Is the right HI LED lit for split vat CONTINUED FROM PRECEEDING PAGE Do elements heat and draw proper amps? Filter System Operation 6.2.3 Troubleshooting the Built-in Filtration System BIH14 units onlyPump Motor Actuation selected frypotCHAPTER 7 SERVICE PROCEDURES 7-1 REPLACE CONTROLLER7-2 REPLACE INTERFACE BOARD Screws securing back covers and tilt housing 7-4 REPLACE TEMPERATURE PROBE7-3 REPLACE TRANSFORMER Screws securing transformers7-4 REPLACE TEMPERATURE PROBE cont 7-4 REPLACE TEMPERATURE PROBE cont 7-5 REPLACE HEATING ELEMENT13. Lower the element into the frypot 4. Disconnect the element springs 7-5 REPLACE HEATING ELEMENT contDisconnect element springs here 7-5 REPLACE HEATING ELEMENT cont Remove the element mounting screws and7-5 REPLACE HEATING ELEMENT cont Use a pin-pusher to remove high-limit wires from connector 7-6 REPLACE HIGH-LIMITPlace tool here when removing and installing high- limit 7-7 REPLACE FRYPOT on old-style contactor boxes 7-8 REPLACE CONTACTORScrews securing wire cover to contactor box optional Location of screws securing contactor box to bottom frame7-12 10. Install the new contactor and connect the wiring removed in Step9. Remove the contactor mounting screws and remove the contactor Contactor mounting screwsPLACEMENT AND FILTER PUMP OPERATION. IMPROPER SCREEN PLACEMENT IS 7-10 BUILT-IN FILTER SYSTEM SERVICE PROCEDURESFiltration Problem Resolution ENSURE THAT FILTER SCREEN IS IN PLACE PRIOR TO FILTER PAPER7-10 BUILT-IN FILTER SYSTEM SERVICE PROCEDURES cont 7-10 BUILT-IN FILTER SYSTEM SERVICE PROCEDURES cont FootPrint III Wiring Diagram7-15 7-11 ELECTRIC INTERFACE BOARD DIAGNOSTIC CHART Diagnostic LED Legend7-12 WIRING DIAGRAMSCOMMON ELECTRIC McDONALDS H14 SERIES- FULL-VAT SIMPLIFIEDCOMMON ELECTRIC McDONALDS H14 SERIES- DUAL-VAT CONTROLLERINTERFACE BOARD COMMON ELECTRIC McDONALDS H14 SERIES- FULL-VAT- EXPORT WYEL3 N GND COMPUTER/CONTROLLERN L1 COMMON ELECTRIC McDONALDS H14 SERIES- DUAL-VAT- EXPORT WYECOMPUTER/CONTROLLER 7-13 WIRING DIAGRAMS, MAIN McDonald’s DomesticMcDonald’s European Community CE McDonald’s European Community CE Prior To 9/98 McDonald’s European Community CE XBIH14 McDonald’s Domestic Contactor McDonald’s European Community CE WYE Contactor McDonald’s European Community CE XBIH14 Contactor McDonald’s 440/480V Contactor McDonald’s Delta CSA Contactor McDonald’s Domestic Control Cord McDonald’s English Control Cord Footprint III, Late Configuration 7-13 WIRING DIAGRAMS, FILTER UNITSFootprint III, Early Configuration TO PUMPPART # H14 SERIES ELECTRIC FRYERS CHAPTER 8 PARTS LIST 8.1 AccessoriesCOMPONENT 8.2.1 MH/BIH114 Cabinet Assembly, Single FootPrint 8.2 Cabinet Assemblies and Component PartsCOMPONENT PART #200-0129 COMPONENT 8.2.2 MH/BIH214, 314, 414, 514 Cabinet AssembliesPART # 200-0081SPCOMPONENT PART #13 826-1374 Screw, #10 ½-Inch Qty PART # 8.3 Casters, Legs and Associated HardwareCOMPONENT PART # 8.4 Component Box Assemblies/Associated Component PartsCOMPONENT 8.5.1 Control Panel Assemblies and Top Caps PART # Control Panel AssemblyCOMPONENT COMPONENT 8.5.1 Door Assembly ComponentsPART # 806-6545SPPART # 8.6 Controller AssembliesCOMPONENT PART # 8.7 Drain System ComponentsCOMPONENT 8.8 Electrical Components Contactors, Elements and Related Components 8.8.1 ContactorsCOMPONENT ITEM PART #1 900-5445 Front Cover, Contactor Box Full-Vat 8.8.2 Elements and Related ComponentsDual-Vat 11Full-VatITEM PART # COMPONENTCOMPONENT 8.8.3 Hood Relay Box, Power Cords and Hood CordsPART # 806-9381SP8.9 Filter Base/Pan Assemblies 8.9.1 Filter Base Assemblies COMPONENT PART #806-8648SP 8.9.2 Filter Pan Assemblies 806-9546SP PART #COMPONENT 806-9547SPPump orientation 8.10 Filter Pump and Motor AssembliesFull-Vat Only Pump orientation required806-6118SP PART #COMPONENT 809-0514Manifold components for all H214, 314, 414 and 514 fryers manufactured before 9/99106-0002SP PART #COMPONENT 106-0054SPPART # 8.11.2 Oil Return Linkage Assemblies and ComponentsCOMPONENT Compression Washers 8.12 Frypot Assemblies and Drain Valve ComponentsFlat Washer Plastic Washer ITEM PART # 8.13 Thermostats and Related Components10 Not used on Full-vat Drain Valve Assemblies COMPONENT