Manuals / Frymaster / Kitchen Appliance / Fryer

Frymaster H14 Series Hood Relay Box, Power Cords and Hood Cords, Part #, Component, 806-9381SP

Models: H14 Series

1 110

Download 110 pages 58.94 Kb

Page 99

8.8.3 Hood Relay Box, Power Cords and Hood Cords

8.8.3 Hood Relay Box, Power Cords and Hood Cords

				15	16
				13
14				8
14
2					17
2				12
3
				4
					18
				9	19
					19
				1
5	7	10	6	11

ITEM	PART #	COMPONENT
1	806-9381SP	Wire Assembly, CE Mac
*	806-9389SP	Wire Assembly, Non-CE Mac
2	807-0070	Terminal, Ground Lug
3	807-1683	Hood Relay, 12VDC
4	807-1694	Strain Relief, HE
5	826-1363	Screw, #8- 32 x ½ (Qty: 25)
6	809-0238	Nut, 4-40 Hex
7	809-0247	Nut, 8-32 Hex
8	809-0359	Screw, #8- 32 x ¼ Hex-slotted
9	809-0492	Nut, Lock
10	809-0656	Screw, 4-40 x 3/8 Round-slotted
11	810-1163	Terminal Block, Screwless
*	807-1973	Terminal, Post (Non-CE)
12	900-8024	Box, Control Cord, CE Mac
13	900-8025	Cover, Control Cord Box
14	901-1530	Bracket, Attaching, Control Panel
15	807-1558	Plug, 4 Pole 5 Wire 20A
16	806-5229	Cordset, 120V 5 Wire (Plug not included)
17	807-2392	Cordset, Power, 3 Phase, 4-Wire w/Plug
18	807-1696	Cordset, Power, Europe, 3-Wire w/Plug
19	806-8164SP	Cordset, Power, Full-vat Export

8-17

Image 99

Frymaster H14 Series Hood Relay Box, Power Cords and Hood Cords, Part #, Component, 806-9381SP, 806-9389SP, 806-8164SP

Contents

SERVICE MANUAL FRYMASTER H14 SERIES ELECTRIC FRYER MANUFACTURED BY FRYMASTER CORPORATION P.O. BOX SHREVEPORT, LOUISIANAPHONE TOLL FREE 1-800-24 FRYER FAX CANADA COMPUTERS FCCD. WARRANTY PROVISIONS - COOKING COMPUTER WARRANTY STATEMENTA. WARRANTY PROVISIONS - FRYERS B. WARRANTY PROVISIONS - FRYPOTSE. PARTS RETURN F. WARRANTY EXCLUSIONSExample of a WARNING box 1.2 Safety InformationCHAPTER 1 INTRODUCTION 1.1 General Example of a CAUTION boxNon-CE specific information 1.3 Computer Information1.4 European Community CE Specific Information CE Standard Example of box used to distinguish CE andWhat to do if your equipment arrives damaged 1.5 Shipping Damage Claim Procedure1.6 Service Information RETAIN AND STORE THIS MANUAL IN A SAFE PLACE FOR FUTURE USEthis or any other appliance CHAPTER 2 INSTALLATION INSTRUCTIONS 2.1 GeneralCopper wire suitable for at least 167 F 75 C MUST be used for power connections DANGERDANGER 2.3 Power Requirements2.2 After Fryers Are Under The Fry Station Hood DANGER2.4 Frypot Boil-Out 3.2 Introduction To The M-100B Cooking Computer 3.1 Equipment Setup and Shutdown ProceduresSetup CHAPTER 3 OPERATING FRYERS WITH M100B COOKING COMPUTERSDESCRIPTION 3.3 M-100B Computer Operating Instructions properly filled with vegetable oil. See SectionOperating the Computer on Full-Vat Fryers Viewing the Frypot Temperature Actual or Setpoint Operating the Computer on Split-Vat FryersCooking Product Full-Vat or Split-Vat Probe Failure Indication 3.4 M-100B Computer Problem Condition IndicatorsLow Temperature Indication Open Drain Valve IndicationRecovery Out of Range REC LOC 3.5.1 M-100B Computer Setup Mode How to Enter the Setup Mode3.5 M-100B Computer Set-Up and Programming Instructions How to Change the Computer’s Display Language How to Configure the Computer for Use on an Electric FryerHow to Change Computer Product/Temperature Displays How to Activate or Deactivate the Frypot BOIL-OUT Feature How to Calibrate Computer Temperature to Actual Frypot Temperature3.5.2 M-100B Computer Programming Mode How to Enter the Program ModeHow to Reset the Computer to the Factory Defaults How to Change the Shake, Pull, Or Quality Times for Menu ItemsHow to Enter a Product Name in a Test Menu How to Change the Cooking Temperature SetpointPage How to Turn the Display of a Factory-Programmed Menu Item On and Off How to Suppress a Shake, QA, or Duty FunctionHow to Display “Use Time” Information How to Display the Product Cycle Accumulator InformationHow to Use the Filter Countdown Timer 4.2 Introduction to the Analog Controller 4.1 Equipment Setup and Shutdown Proceduresswitch to the ON position. Failure to do so could damage the frypot CHAPTER 4 OPERATING FRYERS WITH ANALOG CONTROLLERSA B C D E F G H I J K L M N DESCRIPTIONTools needed Maple Paddle control-check procedure4.3 Analog Controller Operating Instructions 4.4 Analog Controller High-Limit Checkrelease switch CHAPTER 5 OPERATING THE BUILT-IN FILTRATION SYSTEM DESCRIPTIONFUNCTION 8.1 STEP-BY-STEP FILTRATION INSTRUCTIONS Switch computer to OFF Slide the filter pan from the fryer cabinetOpen the filter-cover, and remove and clean the crumb tray Remove and clean the filter screen WARNING Do Not Use Filter Powder on Filter Pads Slide the filter pan back inside fryer cabinet Return handle and drain-valve handle location With fryer off, open drain valveTurn the computer back ON and use right The computer will countdown the process, although it does not control the filtering Close the drain-valve and leave the filter pump on to fill the frypot With the drain-valve closed, frypot fills with oilTurn off filter pump Turn the filter alarm off by pressing Top up oil level. Some oil may be lost in filtering processFill to first mark in frypot 8.2 CARE AND CLEANING OF YOUR FRYER AND FILTER SYSTEM WATER IN THE FILTER PAN MSDU50 Verify that electrical cords are securely plugged in CHAPTER 6 PREVENTIVE MAINTENANCE AND TROUBLESHOOTING6.1 Preventive Maintenance 6.2 TroubleshootingFryer Off 6.2.1 Troubleshooting Fryers Equipped with M100B ComputersFryer Heating Oil CONTINUED FROM PRECEEDING PAGE Is the right HI LED lit for split vat CONTINUED FROM PRECEEDING PAGE Do elements heat and draw proper amps? 6.2.2 Troubleshooting Fryers Equipped with Analog Controllers Fryer OffIs the AL LED illuminated? Fryer Heating Oil CONTINUED FROM PRECEEDING PAGE Is the right HI LED lit for split vat CONTINUED FROM PRECEEDING PAGE Do elements heat and draw proper amps? selected frypot 6.2.3 Troubleshooting the Built-in Filtration System BIH14 units onlyPump Motor Actuation Filter System Operation7-1 REPLACE CONTROLLER CHAPTER 7 SERVICE PROCEDURES7-2 REPLACE INTERFACE BOARD Screws securing transformers 7-4 REPLACE TEMPERATURE PROBE7-3 REPLACE TRANSFORMER Screws securing back covers and tilt housing7-4 REPLACE TEMPERATURE PROBE cont 7-5 REPLACE HEATING ELEMENT 7-4 REPLACE TEMPERATURE PROBE cont13. Lower the element into the frypot 7-5 REPLACE HEATING ELEMENT cont 4. Disconnect the element springsDisconnect element springs here Remove the element mounting screws and 7-5 REPLACE HEATING ELEMENT cont7-5 REPLACE HEATING ELEMENT cont 7-6 REPLACE HIGH-LIMIT Use a pin-pusher to remove high-limit wires from connectorPlace tool here when removing and installing high- limit 7-7 REPLACE FRYPOT Location of screws securing contactor box to bottom frame 7-8 REPLACE CONTACTORScrews securing wire cover to contactor box optional on old-style contactor boxesContactor mounting screws 10. Install the new contactor and connect the wiring removed in Step9. Remove the contactor mounting screws and remove the contactor 7-12ENSURE THAT FILTER SCREEN IS IN PLACE PRIOR TO FILTER PAPER 7-10 BUILT-IN FILTER SYSTEM SERVICE PROCEDURESFiltration Problem Resolution PLACEMENT AND FILTER PUMP OPERATION. IMPROPER SCREEN PLACEMENT IS7-10 BUILT-IN FILTER SYSTEM SERVICE PROCEDURES cont FootPrint III Wiring Diagram 7-10 BUILT-IN FILTER SYSTEM SERVICE PROCEDURES cont7-15 Diagnostic LED Legend 7-11 ELECTRIC INTERFACE BOARD DIAGNOSTIC CHARTSIMPLIFIED WIRING DIAGRAMSCOMMON ELECTRIC McDONALDS H14 SERIES- FULL-VAT 7-12CONTROLLER COMMON ELECTRIC McDONALDS H14 SERIES- DUAL-VATCOMPUTER/CONTROLLER COMMON ELECTRIC McDONALDS H14 SERIES- FULL-VAT- EXPORT WYEL3 N GND INTERFACE BOARDCOMMON ELECTRIC McDONALDS H14 SERIES- DUAL-VAT- EXPORT WYE N L1COMPUTER/CONTROLLER McDonald’s Domestic 7-13 WIRING DIAGRAMS, MAINMcDonald’s European Community CE McDonald’s European Community CE Prior To 9/98 McDonald’s European Community CE XBIH14 McDonald’s Domestic Contactor McDonald’s European Community CE WYE Contactor McDonald’s European Community CE XBIH14 Contactor McDonald’s 440/480V Contactor McDonald’s Delta CSA Contactor McDonald’s Domestic Control Cord McDonald’s English Control Cord TO PUMP 7-13 WIRING DIAGRAMS, FILTER UNITSFootprint III, Early Configuration Footprint III, Late ConfigurationH14 SERIES ELECTRIC FRYERS CHAPTER 8 PARTS LIST 8.1 Accessories PART #COMPONENT 8.2 Cabinet Assemblies and Component Parts 8.2.1 MH/BIH114 Cabinet Assembly, Single FootPrintPART # COMPONENT200-0129 200-0081SP 8.2.2 MH/BIH214, 314, 414, 514 Cabinet AssembliesPART # COMPONENTPART # COMPONENT13 826-1374 Screw, #10 ½-Inch Qty 8.3 Casters, Legs and Associated Hardware PART #COMPONENT 8.4 Component Box Assemblies/Associated Component Parts PART #COMPONENT 8.5.1 Control Panel Assemblies and Top Caps Control Panel Assembly PART #COMPONENT 806-6545SP 8.5.1 Door Assembly ComponentsPART # COMPONENT8.6 Controller Assemblies PART #COMPONENT 8.7 Drain System Components PART #COMPONENT 8.8.1 Contactors 8.8 Electrical Components Contactors, Elements and Related ComponentsITEM PART # COMPONENT1 900-5445 Front Cover, Contactor Box 11Full-Vat 8.8.2 Elements and Related ComponentsDual-Vat Full-VatCOMPONENT ITEM PART #806-9381SP 8.8.3 Hood Relay Box, Power Cords and Hood CordsPART # COMPONENT8.9 Filter Base/Pan Assemblies 8.9.1 Filter Base Assemblies PART # COMPONENT806-8648SP 8.9.2 Filter Pan Assemblies 806-9547SP PART #COMPONENT 806-9546SPPump orientation required 8.10 Filter Pump and Motor AssembliesFull-Vat Only Pump orientation809-0514 PART #COMPONENT 806-6118SPmanufactured before 9/99 Manifold components for all H214, 314, 414 and 514 fryers106-0054SP PART #COMPONENT 106-0002SP8.11.2 Oil Return Linkage Assemblies and Components PART #COMPONENT 8.12 Frypot Assemblies and Drain Valve Components Compression WashersFlat Washer Plastic Washer COMPONENT 8.13 Thermostats and Related Components10 Not used on Full-vat Drain Valve Assemblies ITEM PART #