Intelligent Blade Panel Module | Fujitsu BX600 manual

Extended Configuration Menu

Web-Based Management Interface

Broadcast Packets Received - The total number of packets received that were directed to the broadcast address. Note that this does not include multicast packets.

Packets Received with Errors - The number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol.

Packets Transmitted Without Errors - The total number of packets transmitted out of the interface.

Broadcast Packets Transmitted - The total number of packets that higher-level protocols requested to be transmitted to the Broadcast address, including those that were discarded or not sent.

Transmit Packet Errors - The number of outbound packets that could not be transmitted because of errors.

Address Entries Currently in Use - The total number of Forwarding Database Address Table entries now active on the IBP, including learned and static entries.

Time Since Counters Last Cleared - The elapsed time, in days, hours, minutes, and seconds since the statistics for this IBP were last cleared.

Command Buttons

Clear Counters - Clear all the counters, resetting all summary and detailed statistics to defaults. The discarded packets count cannot be cleared.

Refresh - Refresh the data on the screen with the present state of the data in the IBP.

6.2.4.2.3Viewing Each Port Detailed Statistics Page Selection Criteria

Slot/Port - Selects the interface for which data is to be displayed or configured.

Non-Configurable Data

109	Intelligent Blade Panel Module

Image 110

Fujitsu BX600 manual Intelligent Blade Panel Module

Contents

Primergy BX600 Blade Server Systems Primergy BX600 Blade Server Systems Comments… Suggestions… Corrections… Page Contents Intelligent Blade Panel Module Intelligent Blade Panel Module Intelligent Blade Panel Module Important Notes Information About Boards Compliance Statements Industry Canada Class a LVD Taiwan Bsmi Class a Australia AS/NZS 3548 1995 Class a Introduction Features of the IBP Module Self-Learning MAC Addresses Layer 2 Features Igmp SnoopingVlan Transparency Supported Features Automatic Aging for MAC Addresses Uplink Set Support Service Vlan & Service LAN SupportPort Backup Support Port Group Support Save Configuration as file BootP and Dhcp ClientsIBP Module Management Features Various Files of Management Operation Command Line Interface Snmp Alarms and Trap LogsConfiguration File Download and Upload Provision Locked Port Support Security FeaturePort Based Authentication Radius Client Description of Hardware System LED Internal Ports Page Primergy GbE Switch Blade 30/12 Internal Ports List Primergy BX620 Port LEDs Features and BenefitsStatus of LEDs Connectivity Performance Management Notational Conventions Target Group Electrical data Technical DataDimensions National and international standards Environmental conditions Network Planning Introduction to IBP Connecting to 1000BASE-T Devices Making Network Connections Cable Testing for Existing Category 5 Cable 1000BASE-T Cable Requirements Adjusting Existing Category 5 Cabling for 1000BASE-T 1000BASE-T Pin Assignments Unpacking the IBP Module Package ContentsOverview Connecting the IBP Module Mount the IBP Module Select 2 Console Redirection Switch Blade Start up and Configuration the IBP Module Port Default Settings Configuring the Terminal Under Properties, select VT100 for Emulation mode Booting Device Software Download Erasing the Device ConfigurationBoot Image Download Operation Code CLI Software Download Through Tftp Server System Image Download Tftp Enter y. The device reboots Overview Command Buttons Configurable DataNon-Configurable Data Main Menu Groups Administration View Uplink Set Information Managing Port Groups Configuring Port Group Configuration Command Buttons Viewing Port Group Information Selection Criteria Viewing Vlan Port Group Information Groups Administration Configurable Data Viewing Service LAN Information Groups Administration Configurable Data Viewing Service Vlan Information Groups Administration Managing Port Backup Configuring Port Backup Configuration Viewing Port Backup Status Groups Administration Panel Settings Menu Panel Settings Menu Viewing Panel Description Page Configurable Data Configuring Inband Administration Terminal interface via the EIA-232 port Panel Settings Menu Configuring Telnet Session Page Configurable Data Panel Settings Menu Configuring Serial Port Page Configurable Data Selection Criteria Panel Settings Menu Defining Dhcp Client Configuring Dhcp Restart Configuring Dhcp Client-identifier Defining Snmp Configuring Snmp Community Configuration Configuring Snmp Trap Receiver Configuration Viewing Snmp supported MIBs Panel Settings Menu Panel Settings Menu Viewing Sntp Global Status Non-Configurable Data Configuring Sntp Server Configuration Configurable Data Viewing Sntp Server Status Non-Configurable Data Unknown IPV4 Panel Settings Menu Configurable Data Panel Settings Menu Refresh Refresh the configuration value again Reset the Passwords to Defaults Page Command Buttons Managing System Utilities Panel Reset Command ButtonsReset All Configuration to Defaults Page Command Buttons Configurable Data Uploading Specific Files from Panel Removing Specific File Copying Running Configuration to Panel Defining Ping Function Submit This will initiate the ping Security Menu Viewing Radius Statistics Page Non-Configurable Data Viewing Radius Server Statistics Page Selection Criteria Security Menu Security Menu Resetting All Radius Statistics Page Command Buttons Configurable Data Security Menu Non-Configurable Data Security Menu Extended Configuration Menu Viewing Buffered Log Configuring Command Logger Page Configurable Data Configuring Console Log Viewing Event Log Configuring Hosts configuration Page Configurable Data Configuring syslog configuration Page Configurable Data Extended Configuration Menu Viewing Login Session Page Non-Configurable Data 107 Intelligent Blade Panel Module 108 Intelligent Blade Panel Module 109 Intelligent Blade Panel Module 110 Intelligent Blade Panel Module 111 112 Intelligent Blade Panel Module 113 Intelligent Blade Panel Module Extended Configuration Menu Extended Configuration Menu Viewing Each Port Summary Statistics Page Selection Criteria 117 Intelligent Blade Panel Module 118 Intelligent Blade Panel Module 119 Intelligent Blade Panel Module 120 Intelligent Blade Panel Module Viewing Access Control Summary Page Non-Configurable Data 122 Intelligent Blade Panel Module 123 Intelligent Blade Panel Module Defining Access Control User Login Page Selection Criteria Defining Each Port Access Privileges Page Selection Criteria Extended Configuration Menu Managing IP Filter IP Filter Configuration 128 Intelligent Blade Panel Module Defining User Login 130 Intelligent Blade Panel Module Example Ip address ipaddr netmask vlan-id CLI Command FormatCommand Example Clear port-group Values 2CLI Mode-based TopologyParameters MacAddr ConventionsNetwork Address Syntax Address Type Format Range IPAddr Annotations System Information and Statistics commands Show running-config Show eventlog Show running-config all scriptname Show sysinfo Show hardware Show systemSystem Information Show version Show loginsession Show interface status slot/port all 4Device Configuration CommandsInterface Show interface status Show interface counters Show interfaceShow interface slot/port 142 Intelligent Blade Panel Module Show interface counters detailed slot/port switchport Total Packets Transmitted Octets Total Packets Received Without ErrorsTotal Packets Received with MAC Errors Total Transmited Packets Discards Total Transmit ErrorsTotal Packets Transmitted Successfully 146 Intelligent Blade Panel Module Show interface switch Show interface IBP Interface Interface range Speed-duplex all 10 100 full-duplex half-duplex Speed-duplexSpeed-duplex 10 100 full-duplex half-duplex Full duplex Full duplex half duplex Half duplex Negotiate all no negotiate all NegotiateNegotiate no negotiate Capabilities Storm-control flowcontrol no storm-control flowcontrol DescriptionStorm-control flowcontrol Syntax Show mac-addr-table macaddr all Show mac-address-table igmpsnooping Show mac-address-table multicast Show mac-address-table multicast macaddr vlanid all Show mac-address-table stats Show mac-address-table stats Default SettingShow mac-address-table agetime Default Setting Show mac-address-table agetime Igmp Snooping Show Commands Show igmp snooping Mac-address-table aging-time Port Channel Lacp Configuration Commands IgmpsnoopingIgmpsnooping uplinkSetName no igmpsnooping uplinkSetName Lacp uplinkSetName no lacp uplinkSetName Uplink Sets Show Commands Show lacp Port Group Configuration Commands Uplink-setUplink-set uplinkSetName no uplink-set uplinkSetName Configuration Commands Port-group Port-group portGroupName no port-group portGroupName Port Backup Show Commands Default Setting Command Mode Configuration Commands Port-backupPort-backup uplinkSetName no port-backup uplinkSetName Port-backup no port-backup Link State Show Commands Configuration Commands Linkstate Show vlan-group vlanGroupName Vlan Port Groups Show CommandsLinkstate uplinkSetName no linkstate uplinkSetName Configuration Commands Vlan-group Vlan-group vlanGroupName no vlan-group vlanGroupName 167 Intelligent Blade Panel Module Service LAN Show Commands Configuration Commands Svc-lan Svc-lan svcLanName no svc-lan svcLanName Service Vlan Show Commands Configuration Commands Svc-vlan Svc-vlan svcVlanName no svc-vlan svcVlanName Show ip redirects Management CommandsNetwork Commands Show ip interface Mtu 1518-9216 no mtu Show ip filter1.4 mtu Ip default-gateway gateway no ip default-gateway Command UsageIp default-gateway Ip address Ip address mgmt-vlan Ip address protocol bootp dhcp vlanID noneIp address protocol Ip filter Ip filter no ip filter Serial Interface Commands Show line console Ip filter ipaddr no ip filter ipaddr Line console Baudrate Password-threshold 0-120 no password-threshold Exec-timeoutPassword-threshold Telnet host port debug line echo Telnet Session CommandsSilent-time Show line vty Line vty Exec-timeout 1-160 no exec-timeout Sessions MaxsessionsMaxsessions 0-5 no maxsessions Telnet sessions no telnet sessions Sessions no sessionsTelnet sessions Telnet maxsessions Telnet maxsessions 0-5 no maxsessions Telnet exec-timeoutTelnet exec-timeout 1-160 no telnet exec-timeout Snmp Server Commands Show snmp Show telnet Show trapflags Snmp-server location Snmp-server sysnameSnmp-server sysname name Syntax Snmp-server location loc Snmp-server community name no snmp-server community name Snmp-server contactSnmp-server community 190 Intelligent Blade Panel Module Snmp-server community ro rw name Snmp-server host ipaddr name no snmp-server host name Snmp-server enable trapsSnmp-server host No This command disables Multiple User trap Snmp Trap Commands Show snmptrap Snmp trap link-status all no snmp trap link-status all Snmp trap link-statusSnmp trap link-status no snmp trap link-status Snmptrap ipaddr Snmptrap name ipaddrSnmptrap name ipaddr no snmptrap name ipaddr Http commands Show ip http Snmptrap modeSnmptrap mode name ipaddr no snmptrap mode name ipaddr Snmptrap ipaddr name ipaddr ipaddrnew Ip javamode Ip javamode no ip javamode Ip http server Ip http portIp http port 1-65535 no ip http port Ip http server no ip http server Ip http secure-server Ip http secure-portIp http secure-port portid no ip http secure-port Ip http secure-server no ip http secure-server Secure Shell SSH Commands Show ip ssh Ip http secure-protocol Ip ssh protocol Ip sshIp ssh no ip ssh Ip ssh maxsessions 0-5 no ip ssh maxsessions Ip ssh timeoutIp ssh maxsessions Ip dhcp client-identifier Ip ssh timeout 1-160 no ip ssh timeoutDhcp Client Commands Ip dhcp restart System Burned In MAC Address Lock lockidentifier Exclusive no lock lockidentifierALL Lock CommandsLockmessage messagestring default Lockmessage Lockreset Show lock Show logging buffered System Log Management CommandsShow Commands Show logging Show logging hosts Show logging traplogShow logging traplogs Logging buffered no logging buffered Configuration Commands Logging bufferedDisplay Message Index used for deleting Logging console severitylevel 0-7 no logging console Logging buffered wrap no logging buffered wrapLogging console Logging host Logging host hostaddress port severitylevel Logging syslog no logging syslog Logging host reconfigure hostindex hostaddressLogging syslog Logging syslog port portid no logging syslog port Clear logging buffered Script apply scriptname Script Management CommandsScript apply Script delete Script show scriptname Script listScript show Configuration Commands Username User Account Management CommandsShow Commands Show users Username username password nopassword no username username Username snmpv3 authentication Username snmpv3 encryption Show authentication Security CommandsShow Commands Show users authentication Show authentication users Show dot1x Show dot1x detail Show dot1x statistics Show dot1x statistics slot/port Show dot1x users Show dot1x summaryShow dot1x summary slot/port all Show radius Secret Configured Yes / NoShow radius-servers Radius Accounting Mode Enabled or disabled Show radius accounting statistics ipaddr Show radius statistics ipaddr Secret Configured Yes or NoShow radius statistics Show tacacs Show port-security Show port-security dynamic slot/port Configuration Commands Authentication login Username defaultlogin Possible method values are local, radius, reject, and tacacs Username login Username login user listname 3 Dot1x Configuration Commands 3.1 dot1x initialize 3.2 dot1x default-login 3.4 dot1x system-auth-control 3.3 dot1x loginDot1x login user listname Dot1x system-auth-control no dot1x system-auth-control 3.5 dot1x user 3.6 dot1x port-control 3.7 dot1x max-req 3.9 dot1x re-reauthenticate 3.8 dot1x re-authenticationDot1x re-authentication no dot1x re-authentication Dot1x max-req 1-10 no dot1x max-req 3.10 dot1x timeout Radius Configuration Commands Radius accounting mode Radius accounting mode no radius accounting mode Radius-server host Radius-sever key Radius-server retransmit Retries the maximum number of times Range 1 Radius-server msgauth Radius-server timeoutRadius-server timeout seconds no radius-server timeout Tacacs no tacacs Tacacs Configuration CommandsRadius-server primary Tacacs server-ip Tacacs modeTacacs mode 1-3 master slave no tacacs mode Tacacs server-ip 1-3 ipaddr no tacacs server-ip Tacacs key Tacacs portTacacs port 1-3 1-65535 no tacacs port Tacacs key 1-3 no tacacs key Tacacs retry Tacacs timeoutTacacs timeout 1-3 1-255 no tacacs timeout Tacacs retry 1-3 1-9 no tacacs retry Port-security max-dynamic Port Security Configuration Commands Port-securityPort-security no port-security Default Setting Port-security max-static Port-security max-static 0-20 no port-security max-static Port-security mac-address move Syntax Port-security mac-address move Default SettingPort-security mac-address Show sntp client Sntp CommandsShow Commands Show sntp Configuration Commands Sntp broadcast client poll-interval Sntp client modeSntp client mode broadcast unicast no sntp client mode Sntp unicast client poll-interval Sntp client portSntp client port portid 6-10 no sntp client port Sntp unicast client poll-timeout Sntp unicast client poll-retry Sntp server Sntp clock timezone Sntp clock timezone name 0-12 0-59 before-utc after-utc System Utilities10.2.9 Clear Clear arp Clear traplog Clear eventlog Clear config Clear pass Clear counters Syntax Clear mac-addr-table dynamic Default SettingClear mac address table Clear counters slot/port all Enable passwd Clear igmp snooping Clear dot1x statistics all slot/port Clear ip filterClear dot1x statistics Copy Clear radius statisticsClear tacacs Privileged Exec Files download from PC to board Syntax Copy running-config startup-config filename 11.4 dir Copy clibanner url copy url clibanner no clibannerDelete Boot-system Dir boot-rom config opcode filenameWhichboot Display Message Column Heading Description Boot-system boot-rom config opcode filename Ping Traceroute Calendar set Logging cli-commandSyntax Logging cli-command Default Setting Calendar set mm/dd/yy hhmmss Disconnect ConfigureReload Disconnect 0-10 all Hostname promptstring Promptstring Prompt string Default SettingHostname Quit Dhcp Commands Ip dhcp client-identifier text text hex hex Using Snmp Supported MIBs Standard MIBs are listed in the following table Private enterprise MIB is listed below Accessing MIB Objects RFC 2233 IF-MIB Accessing MIB ObjectsUsing Snmp 279 Intelligent Blade Panel Module Supported Traps Snmp traps supported include the following items Default Settings Overview system default settings Default settings for all the configuration commands SSLPage In-band Administration SSH DSA Key SSH RSA1 Key SSH RSA2 Key Troubleshooting and Tips Diagnosing IBP Indicators Accessing the Management Interface Symptom Action Information on this document