Show ip filter, 1.4 mtu, Mtu 1518-9216 no mtu | Fujitsu BX600

Management Commands

Command Reference

Display Message

IP default gateway: The default gateway for this IP interface. The factory default value is 0.0.0.0

7.5.1.3show ip filter

This command displays management IP filter status and all designated management stations.

Syntax

show ip filter

Default Setting

None

Command Mode

Privileged Exec

Display Message

Index: The index of stations.

IP Address: The IP address of stations that are allowed to make configuration changes to the IBP.

7.5.1.4mtu

This command sets the maximum transmission unit (MTU) size (in bytes) for physical and port-channel (LAG) interfaces. For the standard implementation, the range of <1518-9216> is a valid integer between 1518-9216.

Syntax

mtu <1518-9216> no mtu

<1518-9216> - Max frame size (Range: 1518 - 9216).

no - This command sets the default maximum transmission unit (MTU) size (in bytes) for the interface.

Default Setting

173	Intelligent Blade Panel Module

Image 174

Fujitsu BX600 manual Show ip filter, 1.4 mtu, Mtu 1518-9216 no mtu

Contents

Primergy BX600 Blade Server Systems Primergy BX600 Blade Server Systems Comments… Suggestions… Corrections… Page Contents Intelligent Blade Panel Module Intelligent Blade Panel Module Intelligent Blade Panel Module Important Notes Information About Boards Compliance Statements Industry Canada Class a LVD Taiwan Bsmi Class a Australia AS/NZS 3548 1995 Class a Introduction Features of the IBP Module Self-Learning MAC Addresses Layer 2 Features Igmp SnoopingVlan Transparency Supported Features Automatic Aging for MAC Addresses Uplink Set Support Service Vlan & Service LAN SupportPort Backup Support Port Group Support Save Configuration as file BootP and Dhcp ClientsIBP Module Management Features Various Files of Management Operation Command Line Interface Snmp Alarms and Trap LogsConfiguration File Download and Upload Provision Locked Port Support Security FeaturePort Based Authentication Radius Client Description of Hardware System LED Internal Ports Page Primergy GbE Switch Blade 30/12 Internal Ports List Primergy BX620 Port LEDs Features and BenefitsStatus of LEDs Connectivity Performance Management Notational Conventions Target Group Electrical data Technical DataDimensions National and international standards Environmental conditions Network Planning Introduction to IBP Connecting to 1000BASE-T Devices Making Network Connections Cable Testing for Existing Category 5 Cable 1000BASE-T Cable Requirements Adjusting Existing Category 5 Cabling for 1000BASE-T 1000BASE-T Pin Assignments Package Contents OverviewUnpacking the IBP Module Connecting the IBP Module Mount the IBP Module Select 2 Console Redirection Switch Blade Start up and Configuration the IBP Module Port Default Settings Configuring the Terminal Under Properties, select VT100 for Emulation mode Booting Device Erasing the Device Configuration Boot Image DownloadSoftware Download Operation Code CLI Software Download Through Tftp Server System Image Download Tftp Enter y. The device reboots Overview Command Buttons Configurable DataNon-Configurable Data Main Menu Groups Administration View Uplink Set Information Managing Port Groups Configuring Port Group Configuration Command Buttons Viewing Port Group Information Selection Criteria Viewing Vlan Port Group Information Groups Administration Configurable Data Viewing Service LAN Information Groups Administration Configurable Data Viewing Service Vlan Information Groups Administration Managing Port Backup Configuring Port Backup Configuration Viewing Port Backup Status Groups Administration Panel Settings Menu Panel Settings Menu Viewing Panel Description Page Configurable Data Configuring Inband Administration Terminal interface via the EIA-232 port Panel Settings Menu Configuring Telnet Session Page Configurable Data Panel Settings Menu Configuring Serial Port Page Configurable Data Selection Criteria Panel Settings Menu Defining Dhcp Client Configuring Dhcp Restart Configuring Dhcp Client-identifier Defining Snmp Configuring Snmp Community Configuration Configuring Snmp Trap Receiver Configuration Viewing Snmp supported MIBs Panel Settings Menu Panel Settings Menu Viewing Sntp Global Status Non-Configurable Data Configuring Sntp Server Configuration Configurable Data Viewing Sntp Server Status Non-Configurable Data Unknown IPV4 Panel Settings Menu Configurable Data Panel Settings Menu Refresh Refresh the configuration value again Managing System Utilities Panel Reset Command Buttons Reset All Configuration to Defaults Page Command ButtonsReset the Passwords to Defaults Page Command Buttons Configurable Data Uploading Specific Files from Panel Removing Specific File Copying Running Configuration to Panel Defining Ping Function Submit This will initiate the ping Security Menu Viewing Radius Statistics Page Non-Configurable Data Viewing Radius Server Statistics Page Selection Criteria Security Menu Security Menu Resetting All Radius Statistics Page Command Buttons Configurable Data Security Menu Non-Configurable Data Security Menu Extended Configuration Menu Viewing Buffered Log Configuring Command Logger Page Configurable Data Configuring Console Log Viewing Event Log Configuring Hosts configuration Page Configurable Data Configuring syslog configuration Page Configurable Data Extended Configuration Menu Viewing Login Session Page Non-Configurable Data 107 Intelligent Blade Panel Module 108 Intelligent Blade Panel Module 109 Intelligent Blade Panel Module 110 Intelligent Blade Panel Module 111 112 Intelligent Blade Panel Module 113 Intelligent Blade Panel Module Extended Configuration Menu Extended Configuration Menu Viewing Each Port Summary Statistics Page Selection Criteria 117 Intelligent Blade Panel Module 118 Intelligent Blade Panel Module 119 Intelligent Blade Panel Module 120 Intelligent Blade Panel Module Viewing Access Control Summary Page Non-Configurable Data 122 Intelligent Blade Panel Module 123 Intelligent Blade Panel Module Defining Access Control User Login Page Selection Criteria Defining Each Port Access Privileges Page Selection Criteria Extended Configuration Menu Managing IP Filter IP Filter Configuration 128 Intelligent Blade Panel Module Defining User Login 130 Intelligent Blade Panel Module Example Ip address ipaddr netmask vlan-id CLI Command FormatCommand Example Clear port-group 2CLI Mode-based Topology ParametersValues MacAddr ConventionsNetwork Address Syntax Address Type Format Range IPAddr Annotations System Information and Statistics commands Show running-config Show eventlog Show running-config all scriptname Show sysinfo Show system System InformationShow hardware Show version Show loginsession 4Device Configuration Commands Interface Show interface statusShow interface status slot/port all Show interface Show interface slot/portShow interface counters 142 Intelligent Blade Panel Module Show interface counters detailed slot/port switchport Total Packets Received Without Errors Total Packets Received with MAC ErrorsTotal Packets Transmitted Octets Total Transmit Errors Total Packets Transmitted SuccessfullyTotal Transmited Packets Discards 146 Intelligent Blade Panel Module Show interface switch Show interface IBP Interface Interface range Speed-duplex all 10 100 full-duplex half-duplex Speed-duplexSpeed-duplex 10 100 full-duplex half-duplex Full duplex Full duplex half duplex Half duplex Negotiate Negotiate no negotiateNegotiate all no negotiate all Capabilities Description Storm-control flowcontrolStorm-control flowcontrol no storm-control flowcontrol Syntax Show mac-addr-table macaddr all Show mac-address-table igmpsnooping Show mac-address-table multicast Show mac-address-table multicast macaddr vlanid all Show mac-address-table stats Show mac-address-table stats Default SettingShow mac-address-table agetime Default Setting Show mac-address-table agetime Igmp Snooping Show Commands Show igmp snooping Mac-address-table aging-time Port Channel Lacp Configuration Commands IgmpsnoopingIgmpsnooping uplinkSetName no igmpsnooping uplinkSetName Lacp uplinkSetName no lacp uplinkSetName Uplink Sets Show Commands Show lacp Configuration Commands Uplink-set Uplink-set uplinkSetName no uplink-set uplinkSetNamePort Group Configuration Commands Port-group Port-group portGroupName no port-group portGroupName Port Backup Show Commands Default Setting Command Mode Configuration Commands Port-backupPort-backup uplinkSetName no port-backup uplinkSetName Port-backup no port-backup Link State Show Commands Configuration Commands Linkstate Vlan Port Groups Show Commands Linkstate uplinkSetName no linkstate uplinkSetNameShow vlan-group vlanGroupName Configuration Commands Vlan-group Vlan-group vlanGroupName no vlan-group vlanGroupName 167 Intelligent Blade Panel Module Service LAN Show Commands Configuration Commands Svc-lan Svc-lan svcLanName no svc-lan svcLanName Service Vlan Show Commands Configuration Commands Svc-vlan Svc-vlan svcVlanName no svc-vlan svcVlanName Management Commands Network Commands Show ip interfaceShow ip redirects Show ip filter 1.4 mtuMtu 1518-9216 no mtu Ip default-gateway gateway no ip default-gateway Command UsageIp default-gateway Ip address Ip address protocol bootp dhcp vlanID none Ip address protocolIp address mgmt-vlan Ip filter Ip filter no ip filter Serial Interface Commands Show line console Ip filter ipaddr no ip filter ipaddr Line console Baudrate Exec-timeout Password-thresholdPassword-threshold 0-120 no password-threshold Telnet Session Commands Silent-timeTelnet host port debug line echo Show line vty Line vty Exec-timeout 1-160 no exec-timeout Maxsessions Maxsessions 0-5 no maxsessionsSessions Telnet sessions no telnet sessions Sessions no sessionsTelnet sessions Telnet maxsessions Telnet exec-timeout Telnet exec-timeout 1-160 no telnet exec-timeoutTelnet maxsessions 0-5 no maxsessions Snmp Server Commands Show snmp Show telnet Show trapflags Snmp-server location Snmp-server sysnameSnmp-server sysname name Syntax Snmp-server location loc Snmp-server contact Snmp-server communitySnmp-server community name no snmp-server community name 190 Intelligent Blade Panel Module Snmp-server community ro rw name Snmp-server enable traps Snmp-server hostSnmp-server host ipaddr name no snmp-server host name No This command disables Multiple User trap Snmp Trap Commands Show snmptrap Snmp trap link-status Snmp trap link-status no snmp trap link-statusSnmp trap link-status all no snmp trap link-status all Snmptrap name ipaddr Snmptrap name ipaddr no snmptrap name ipaddrSnmptrap ipaddr Http commands Show ip http Snmptrap modeSnmptrap mode name ipaddr no snmptrap mode name ipaddr Snmptrap ipaddr name ipaddr ipaddrnew Ip javamode Ip javamode no ip javamode Ip http server Ip http portIp http port 1-65535 no ip http port Ip http server no ip http server Ip http secure-server Ip http secure-portIp http secure-port portid no ip http secure-port Ip http secure-server no ip http secure-server Secure Shell SSH Commands Show ip ssh Ip http secure-protocol Ip ssh Ip ssh no ip sshIp ssh protocol Ip ssh timeout Ip ssh maxsessionsIp ssh maxsessions 0-5 no ip ssh maxsessions Ip ssh timeout 1-160 no ip ssh timeout Dhcp Client Commands Ip dhcp restartIp dhcp client-identifier System Burned In MAC Address Lock lockidentifier Exclusive no lock lockidentifierALL Lock CommandsLockmessage messagestring default Lockmessage Lockreset Show lock System Log Management Commands Show Commands Show loggingShow logging buffered Show logging traplog Show logging traplogsShow logging hosts Configuration Commands Logging buffered Display Message Index used for deletingLogging buffered no logging buffered Logging buffered wrap no logging buffered wrap Logging consoleLogging console severitylevel 0-7 no logging console Logging host Logging host hostaddress port severitylevel Logging host reconfigure hostindex hostaddress Logging syslogLogging syslog no logging syslog Logging syslog port portid no logging syslog port Clear logging buffered Script apply scriptname Script Management CommandsScript apply Script delete Script list Script showScript show scriptname User Account Management Commands Show Commands Show usersConfiguration Commands Username Username username password nopassword no username username Username snmpv3 authentication Username snmpv3 encryption Security Commands Show Commands Show users authenticationShow authentication Show authentication users Show dot1x Show dot1x detail Show dot1x statistics Show dot1x statistics slot/port Show dot1x summary Show dot1x summary slot/port allShow dot1x users Secret Configured Yes / No Show radius-serversShow radius Radius Accounting Mode Enabled or disabled Show radius accounting statistics ipaddr Secret Configured Yes or No Show radius statisticsShow radius statistics ipaddr Show tacacs Show port-security Show port-security dynamic slot/port Configuration Commands Authentication login Username defaultlogin Possible method values are local, radius, reject, and tacacs Username login Username login user listname 3 Dot1x Configuration Commands 3.1 dot1x initialize 3.2 dot1x default-login 3.4 dot1x system-auth-control 3.3 dot1x loginDot1x login user listname Dot1x system-auth-control no dot1x system-auth-control 3.5 dot1x user 3.6 dot1x port-control 3.7 dot1x max-req 3.9 dot1x re-reauthenticate 3.8 dot1x re-authenticationDot1x re-authentication no dot1x re-authentication Dot1x max-req 1-10 no dot1x max-req 3.10 dot1x timeout Radius Configuration Commands Radius accounting mode Radius accounting mode no radius accounting mode Radius-server host Radius-sever key Radius-server retransmit Retries the maximum number of times Range 1 Radius-server timeout Radius-server timeout seconds no radius-server timeoutRadius-server msgauth Tacacs Configuration Commands Radius-server primaryTacacs no tacacs Tacacs server-ip Tacacs modeTacacs mode 1-3 master slave no tacacs mode Tacacs server-ip 1-3 ipaddr no tacacs server-ip Tacacs key Tacacs portTacacs port 1-3 1-65535 no tacacs port Tacacs key 1-3 no tacacs key Tacacs retry Tacacs timeoutTacacs timeout 1-3 1-255 no tacacs timeout Tacacs retry 1-3 1-9 no tacacs retry Port Security Configuration Commands Port-security Port-security no port-security Default SettingPort-security max-dynamic Port-security max-static Port-security max-static 0-20 no port-security max-static Syntax Port-security mac-address move Default Setting Port-security mac-addressPort-security mac-address move Sntp Commands Show Commands Show sntpShow sntp client Configuration Commands Sntp client mode Sntp client mode broadcast unicast no sntp client modeSntp broadcast client poll-interval Sntp client port Sntp client port portid 6-10 no sntp client portSntp unicast client poll-interval Sntp unicast client poll-timeout Sntp unicast client poll-retry Sntp server Sntp clock timezone Sntp clock timezone name 0-12 0-59 before-utc after-utc System Utilities10.2.9 Clear Clear arp Clear traplog Clear eventlog Clear config Clear pass Clear counters Syntax Clear mac-addr-table dynamic Default SettingClear mac address table Clear counters slot/port all Enable passwd Clear igmp snooping Clear ip filter Clear dot1x statisticsClear dot1x statistics all slot/port Clear radius statistics Clear tacacsCopy Privileged Exec Files download from PC to board Syntax Copy running-config startup-config filename Copy clibanner url copy url clibanner no clibanner Delete11.4 dir Boot-system Dir boot-rom config opcode filenameWhichboot Display Message Column Heading Description Boot-system boot-rom config opcode filename Ping Traceroute Calendar set Logging cli-commandSyntax Logging cli-command Default Setting Calendar set mm/dd/yy hhmmss Disconnect ConfigureReload Disconnect 0-10 all Hostname promptstring Promptstring Prompt string Default SettingHostname Quit Dhcp Commands Ip dhcp client-identifier text text hex hex Using Snmp Supported MIBs Standard MIBs are listed in the following table Private enterprise MIB is listed below Accessing MIB Objects RFC 2233 IF-MIB Accessing MIB ObjectsUsing Snmp 279 Intelligent Blade Panel Module Supported Traps Snmp traps supported include the following items Default Settings Overview system default settings Default settings for all the configuration commands SSLPage In-band Administration SSH DSA Key SSH RSA1 Key SSH RSA2 Key Troubleshooting and Tips Diagnosing IBP Indicators Accessing the Management Interface Symptom Action Information on this document