Environmental and power requirements | Fujitsu MCJ3230AP manual

Specifications

2.1.3 Environmental and power requirements

Table 2.3 lists the environmental and power requirements.

Table 2.3 Environmental and power requirements (1 of 2)

		Item		Specification

	Power	Average	+5 VDC±5%, 1.4 A (2.5 A Max.) (*1)
	requirements		Ripple requirement 100mV P-P (DC-1 MHz)
			Ripple requirement 100mV P-P (DC-1 MHz)

	Power	Ready (active mode)	4.3 W (typical) (*2)
	consumption
	consumption	Random seek, read/ write	5.6 W (typical) (*2)
	(Average)	Random seek, read/ write	5.6 W (typical) (*2)
	(Average)
		Physical Format	7.0 W (typical) (*2)

		Power save mode
		Pre-idle mode	3.8 W (typical) (*2)
		Idle mode	1.3 W (typical) (*2)
		Standby mode	0.7 W (typical) (*2)
		Sleep mode	0.7 W (typical) (*2)

	Dimensions	With panel	101.6 # 150.0 # 25.4 mm
	(W#D#H)
	(W#D#H)	Without panel	101.6 # 148.4 # 25.4 mm
		Without panel	101.6 # 148.4 # 25.4 mm

	Weight		480 g (with panel)

	Environmental	Operating	Temperature:	5 to 45°C (*3)
	requirements			(gradient 15°C /h or less)
			Relative humidity: 10 to 85% (Noncondensing)
			Max. wet bulb temperature: 29°C or lower

		Non Operating	Temperature:	0 to 50°C
			Relative humidity: 10 to 85% (Noncondensing)
			Max. wet bulb temperature: 36°C or lower

		Transport	Temperature:	-40 to 60°C (24 hours or less)
			Temperature:	-20 to 60°C (24 hours or more)
			Relative humidity: 5 to 90% (Non condensing)
			Max. wet bulb temperature: 41°C or lower

	Installation	Tilt angle	-5° to +10° (*3)

	Vibration/	Operating	3.9 m/s2 (5 to 500 Hz, sine sweep)
	shock		1.96 m/s2 (5 to 500 Hz, sine sweep AV record/play)
			Shock 19.6 m/s2 (10ms, half-sine pulse)

		Non Operating	9.8 m/s2 (5 to 500 Hz, sine sweep)
		No cartridge, power ON	Shock 49 m/s2 (10 ms, half-sine pulse)

		Transport	Shock 490 m/s2 (10 ms, half-sine pulse)
			Requirement: Packing conditions specified by
			Fujitsu

2-4	C156-E205-01EN

Image 40

Fujitsu MCJ3230AP manual Environmental and power requirements 1

Contents

MCJ3230AP Optical Disk Drive Product Manual For Safe Operation Handling of This Manual Revision History This page is intentionally left blank Page Preface Overview of Manual Glossary Conventions for Alert MessagesAcronyms and Abbreviations Preface Disclaimer Important Alert Messages Important Alert ItemsDevice damage Important Alert Items This manual ATA/ATAPI-5 AnsiISO/IEC JTC1 *1 Fujitsu Limited Contents Contents Host Interface Reset response Signature Read Long command Receive Diagnostic Results command Operation and Cleaning AB-1 GL-1IN-1 Illustrations Figures Tables GET Media Status command Mode Parameter List Mode Parameter Header Head cleaner Page This page is intentionally left blank Features General Description Performance Reliability Maintainability/operability Interface AdaptabilityATA/ATAPI-4 Features Drive Configuration Drive model Configuration Mechanical sections Control circuit section block diagram Control circuit section Drive Configuration System Configuration System configuration with one optical disk drive Specifications Optical Disk Drive SpecificationsModel and product number Model and order number Drive specifications Specifications 1 Specifications 2 Optical disk cartridge MB media GB media Density Environmental and power requirements Environmental and power requirements 1 Error rate Environmental and power requirements 2 MTBF= Recommended optical disk cartridge specifications Optical Disk Cartridge SpecificationsRecommended optical disk cartridge specifications Optical disk cartridge Optical disk cartridge Optical Disk Cartridge Specifications Disk specifications Disk specifications Defect management schematic diagram Defect Management Example of alternate processing Temperature measurement point Installation RequirementsEnvironmental Requirements Surface temperature measurement points Temperature requirements at measurement points Temperature requirements and measuring methodAir flow Temperature at each measuring point Reference Temperature rise under several conditionsAir purity External dimensions Mounting Requirements Dimensions Dimensions without panel Installation direction Installation directions Centers of gravity Centers of gravity Mounting frame structure Service clearance Power Supply Requirements Current waveform +5 VDC Drive connectors Cable ConnectionsCN1 +5 VDC Return GND Cable connector specifications Cable connector specificationsDrive connection Jumper settings at factory shipping Jumper SettingsMode setting 13 Slave device setting 15 Cable select examples General notes Page 16 Packing style Mounting Mounting procedureChecks before mounting the drive Confirming initial operations Dismounting Drive Connection check Installation Requirements Host Interface Connector pin assignments 1/2 Pin Assignment Connector pin assignments 2/2 Signal Description Signal description 1/2 Signal description 2/2 Interface Registers 1 I/O registersI/O port functions and mapping DA1 DA0 ATA Command register Alternate Status registerBit definitions of Alternate Status register Data register Drive Address register Bit definitions of Drive Address registerAtapi Byte Count register Bit definitions of Atapi Byte Count register Error register Bit definitions of Error registerAtapi Block Device Select register Bit definitions of Atapi Block Device Select register ATA Features register Atapi Features register10 Bit definitions of Atapi Features register ATA Sector Count register 1.13 Sector Number register 1.14 Atapi Status register12 I/O and C/D BSY Drdy Host Interface Reset response Various Processes Defect sector management SignatureAutomatic alternate sector assignment function Data buffer Cache functionRead cache Media status notification function MO write cache Power management function Power modeActive mode Pre-idle mode Idle mode Standby modeSleep mode Standby timer Power mode transition Unsupported functions LED Indications 16 LED indications ATA Commands 17 Command codes and parameters Check Power Mode E5h 19 Power mode indication Execute Device Diagnostic 90h Device Reset 08h20 Device Reset command When device 1 is connected 22 Self-diagnosis detailed code 23 Flush Cache command 24 GET Media Status commandFlush Cache E7h GET Media Status DAh 25 Error register Identify Packet Device A1h 27 Device parameter information 1/6 27 Device parameter information 2/6 27 Device parameter information 3/6 27 Device parameter information 4/6 27 Device parameter information 5/6 27 Device parameter information 6/6 28 Idle Immediate command 29 NOP commandIdle Immediate E1h NOP 00h 30 Packet command Packet A0h SET Features EFh 31 SET Features command32 FR register setting value DEV 34 Cylinder Low register 33 Transfer setting values in the SC register35 Cylinder High register 36 Sleep command Sleep E6h Standby Immediate E0h Packet Commands 38 Packet command codes and parameters Erase command 39 Erase command 40 Format Unit command Format Unit command41 Format Unit parameter list Inquiry command 43 Inquiry command 44 Inquiry data RMB 45 Mode Select 6 command Mode Select 6 command46 Mode parameters 48 Mode parameter header 47 Mode parameter list49 Block descriptor 50 Mode Page Format Read-Write error recovery 52 Changeable values in the read-write recovery Flexible disk 54 Flexible disk 55 Changeable values in flexible disk WCE Caching 57 Caching58 Changeable values in the caching Power Condition 60 Power Condition 61 Power Condition Page Variable 64 Verify Mode 62 Power Condition Page Default valueVerify Control 63 Verify Control Mode Select 10 command Verify Control Page default value67 Mode Select 10 command Verify Control Page variable 68 Mode Parameter List 69 Mode Parameter Header 70 Mode Sense 6 command Mode Sense 6 command71 Page Control field 72 Mode parameter list 73 Mode parameter header Mode Sense 10 command 75 Mode Page Format76 Mode Sense 10 command 74 Block descriptor 77 Mode Parameter List 78 Mode Parameter Header PREVENT/ALLOW Medium Removal command 79 PREVENT/ALLOW Medium Removal command80 Response to Prevent/Allow/Eject START/STOP Unit Sense KEY Read 10 command Read Capacity command81 Read 10 command 82 Read Capacity command 11READ Format Capacities command 84 Read Format Capacities command83 Read Capacity data 85 Read Format Capacities data format Read Defect Data 10 command 89 Read Defect Data 10 command87 Current/Maximum capacity descriptor 88 Descriptor code definition 90 Defect List Format Read Defect Data 91 Defect List Header Read Defect Data Read Defect Data 12 command 94 Read Defect Data 12 command93 Sector Address Format 95 Defect List Format Read Defect Data 97 Read Long command Read Long command96 Defect List Header Read Defect Data 98 Receive Diagnostic Results command Receive Diagnostic Results commandRequest Sense command 99 Request Sense command 101 Error code 100 Request sense data 102 Sense Key code 103 Logical block address format 104 ASC/ASCQ list 1/2 104 ASC/ASCQ list 2/2 105 Format Progress Indication Bytes Send Diagnostic command Seek command106 Send Diagnostic command 107 Seek command 108 START/STOP Unit command START/STOP Unit command109 START/STOP/EJECT processing Synchronize Cache command Test Unit Ready command110 Synchronize Cache command 111 Test Unit Ready command Verify command Write 10 command112 Verify command 113 Write 10 command Write and Verify command 114 Write and Verify command 115 Write Buffer command Write Buffer commandTnfy Write Long command 116 Write Long command Timing Register/PIO data transfer timingWrite Read 117 Register/PIO data transfer timing parameters Multiword DMA data transfer timing Dmarq Dmack DIOR/DIOW Read 118 Multiword DMA data transfer timing parameters Ultra DMA data in transfer initialization timing Ultra DMA data in transfer continuous transfer timing Ultra DMA data in transfer host stop timing Ultra DMA data in transfer device end timing Ultra DMA data in transfer host end timing Ultra DMA data in transfer host end timing Ultra DMA data out transfer initialization timing Ultra DMA data out transfer continuous transfer timing Ultra DMA data out transfer device stop timing 11 Ultra DMA data out transfer device stop timing Ultra DMA data out transfer host suspend timing 12 Ultra DMA data out transfer host suspend timing Ultra DMA data out transfer device end timing 13 Ultra DMA data out transfer device end timing 119 Ultra DMA data out transfer parameter Power-on and Reset Timing 14 Power-on and reset timing 120 Power-on and reset timing This page is intentionally left blank Operation and Cleaning Operating Optical Disk Drive Optical disk drive Optical disk drive front view with panel Inserting cartridge Operating Optical Disk Drive Inserting cartridge Ejecting removing cartridge Removing cartridge Cleaning Drive Head cleaner Optical Disk Cartridge Operation Optial disk cartridge Write protect tab Write protect tab How to affix an index label on the MO cartridge See figure How to stick an index label on the MO cartridge Operation and Cleaning Cleaning Optical Disk Cartridge Cleaning toolCleaning kit Packed items cleaning kit Cleaning procedure Cleaning procedure Cleaning procedure 10 Cleaning procedure Self-diagnostic function Diagnosis and MaintenanceDiagnosis Initial self-diagnosis Diagnostic commandTest program Maintenance Information Maintenance requirements Revision number REV. no Glossary Error correction code Error detection and correctionRecording power Disk reference surface Status This page is intentionally left blank Acronyms and Abbreviations ODD ODFOEM PCA Index Execute Device Diagnostic 4-23 Execute Device Diagnostic Index General description 1-1 General notes Receive Diagnostic Results Index This page is intentionally left blank Fujitsu Limited This page is intentionally left blank READER’S Comment Form MCJ3230AP Optical Disk