Manuals / Fujitsu / Computer Equipment / Computer Drive

Fujitsu MPA3035AT manual At command issuance I/O registers setting contents, 1F7 HCM, X98 or XE5

Models: MPA3017AT MPA3035AT MPA3026AT MPA3052AT MPA3043AT

1 176

Download 176 pages 49.61 Kb

Page 108

X'98' or X'E5'

At command issuance (I/O registers setting contents)

1F7H(CM)				X'98' or X'E5'

1F6H(DH)	×	×	×	DV		xx

1F5H(CH)				xx
1F4H(CL)				xx
1F3H(SN)				xx
1F2H(SC)				xx
1F1H(FR)				xx

At command completion (I/O registers contents to be read)

1F7H(ST)				Status information

1F6H(DH)	×	×	×		DV		xx

1F5H(CH)					xx
1F4H(CL)					xx
1F3H(SN)					xx
1F2H(SC)					X'00' or X'FF'
1F1H(ER)				Error information

(28)SMART (X'B0)

This command performs operations for device failure predictions according to a subcommand specified in the FR register. If the value specified in the FR register is supported, the Aborted Command error is posted.

It is necessary for the host to set the keys (CL = 4Fh and CH = C2h) in the CL and CH registers prior to issuing this command. If the keys are set incorrectly, the Aborted Command error is posted.

In the default setting, the failure prediction feature is disabled. In this case, the Aborted Command error is posted in response to subcommands other than SMART Enable Operations (FR register = D8h).

When the failure prediction feature is enabled, the device collects or updates several items to forecast failures. In the following sections, note that the values of items collected or updated by the device to forecast failures are referred to as attribute values.

C141-E034-02EN

5 - 47

Image 108

Fujitsu MPA3035AT manual At command issuance I/O registers setting contents, 1F7 HCM, X98 or XE5, 1F6 HDH, 1F5 HCH, 1F4 HCL

Contents

MPA3017AT MPA3026AT MPA3035AT MPA3043AT MPA3052AT DISK DRIVES PRODUCT MANUALC141-E034-02EN Revised contents REVISION RECORDEdition Date publishedDEVICE CONFIGURATION INSTALLATION CONDITIONSPREFACE ChapterConventions for Alert Messages LIABILITY EXCEPTION C141-E034-02ENCONTENTS CHAPTERCHAPTER CHAPTERCHAPTER CHAPTERCommand block registers Host CommandsCommand code and parameters Command descriptionsPower save mode Power commandsData buffer configuration 6.3.1FIGURES Protocol for command abort WRITE SECTORS command protocolProtocol for the command execution without data transfer Host pausing an Ultra DMA data in burstTABLES 1.1 Features 1.2 Device Specifications 1.3 Power Requirements 1.4 Environmental Specifications 1.5 Acoustic Noise1.6 Shock and Vibration 1.7 Reliability 1.8 Error Rate 1.1 Features 1.1.1 Functions and performance1.1.2 Adaptability 1.1.3 Interface5 Error correction and retry by ECC 6 Write cacheC141-E034-02EN 1.2 Device Specifications 1.2.1 Specifications summary Table 1.1 Specifications1.3 Power Requirements 1.2.2 Model and product numberTable 1.2 Model names and product numbers Table 1.3 Current and power dissipation Figure 1.1 Current fluctuation Typ. at +5V when power is turned on 1.4 Environmental Specifications Environmental specificationsTable 1.5 Acoustic noise specification 1.5 Acoustic NoiseTable 1.6 Shock and vibration specification 1.6 Shock and Vibration1.7 Reliability 1.8 Error Rate 1.9 Media DefectsCHAPTER 2 DEVICE CONFIGURATION 2.1 Device Configuration 2.2 System Configuration2.1 Device Configuration Figure 2.1 Disk drive outerview1 Disk MPA3017AT 1 disk MPA3026AT 2 disks MPA3035AT 2 disksMPA3043AT 3 disks MPA3052AT 3 disks 2 Head C141-E034-02ENFigure 2.2 Configuration of disk media heads 2.2 System Configuration 2.2.1 ATA interface Figure 2.3 1 drive system configuration2.2.2 1 drive connection Figure 2.4 2 drives configuration 2.2.3 2 drives connectionHost HA Host adaptor AT bus Host interfaceCHAPTER 3 INSTALLATION CONDITIONS 3.1 Dimensions 3.2 Mounting 3.3 Cable Connections 3.4 Jumper Settings3.1 Dimensions Figure 3.1 Dimensions C141-E034-02EN3.2 Mounting Figure 3.2 OrientationFigure 3.3 Limitation of side-mounting Figure 3.4 Mounting frame structurecabinet Figure 3.5 Surface temperature measurement points Table 3.1 Surface temperature measurement points and standard valuesService area Mounting screw hole3.3 Cable Connections 3.3.1 Device connector Figure 3.7 Connector locations∙ Power supply connector CN1 ∙ ATA interface connector CN1 Power supply connector CN1 Mode Setting Pins ATA interface connector3.3.2 Cable connector specifications Table 3.2 Cable connector specifications3.3.3 Device connection Figure 3.8 Cable connections3.3.4 Power supply connector CN1 Figure 3.9 Power supply connector pins CN1 3.4 Jumper Settings3.4.1 Location of setting jumpers Figure 3.10 Jumper location3.4.2 Factory default setting Figure 3.11 Factory default setting 3.4.3 Jumper configurationFigure 3.12 Jumper setting of master or slave device Figure 3.13 Jumper setting of Cable Select Figure 3.14 Example 1 of Cable SelectFigure 3.15 Example 2 of Cable Select 3 Special setting 1 SP1 a Default modeMaster Device Slave Device4.1 Outline 4.2 Subassemblies 4.3 Circuit Configuration 4.4 Power-on sequence 4.5 Self-calibration 4.6 Read/Write circuitCHAPTER 4 THEORY OF DEVICE OPERATION 4.7 Servo Control4.2.2 Head Figure 4.1 Head structure4.2.3 Spindle 4.2.4 Actuator4.2.5 Air filter 4.3 Circuit Configuration Figure 4.2 MPA30xxAT Block diagram C141-E034-02EN4.4 Power-on Sequence Figure 4.3 Power-on operation sequence 4.5.1 Self-calibration contents 4.5 Self-calibrationTable 4.1 Self-calibration execution timechart 4.5.3 Command processing during self-calibration4.6 Read/write Circuit 4.6.1 Read/write preamplifier PreAMP4.6.2 Write circuit Table 4.2 Write precompensation algorithmFigure 4.4 Read/write circuit block diagram C141-E034-02ENFigure 4.5 Frequency characteristic of programmable filter 4.6.3 Read circuitFigure 4.6 PR4 signal transfer C141-E034-02EN4.6.4 Time base generator circuit Table 4.3 Write clock frequency and transfer rate of each zone 4.7 Servo ControlFigure 4.7 Block diagram of servo control circuit 4.7.1 Servo control circuitFigure 4.8 Physical sector servo configuration on disk surface c. Seek to specified cylinderDrives the VCM to position the head to the specified cylinder d. Calibration5 Power amplifier 2 Servo burst capture circuit3 A/D converter ADC 4 D/A converter DAC4.7.2 Data-surface servo format 4.7.3 Servo frame formatFigure 4.9 Servo frame format 4.7.4 Actuator motor control 4.7.5 Spindle motor control 2 Acceleration mode 3 Stable rotation modeC141-E034-02EN 5.1 Physical Interface 5.2 Logical Interface 5.3 Host Commands 5.4 Command Protocol 5.5 Ultra DMA Feature Set 5.6 TimingCHAPTER INTERFACE5.1 Physical Interface 5.1.1 Interface signals Figure 5.1 Interface signals5.1.2 Signal assignment on the connector Table 5.1 Signal assignment on the interface connectorsignal This signal is used for DMA transfer between the host system and the 5.2 Logical Interface 5.2.1 I/O registersI/O registers 5.2.2 Command block registers Diagnostic code X01 No Error Detected X02 HDC Register Compare Error X03 Data Buffer Compare Error X05 ROM Sum Check Error3 Features register X1F1 X80 Device 1 slave device Failed6 Cylinder Low register X1F4 9 Status register X1F7 DRDYCORR C141-E034-02EN10 Command register X1F7 AlwaysC141-E034-02EN 5.3 Host Commands 5.2.3 Control block registers5.3.1 Command code and parameters Table 5.3 Command code and parameters 1 ofTable 5.3 Command code and parameters 2 of 5.3.2 Command descriptions Transfer sector countAt command issuance I/O registers setting contents 1 READ SECTORS X20 or1F7 HCM 1F6 HDHAt command completion I/O registers contents to be read Error information1F7 HST Status informationFigure 5.2 Execution example of READ MULTIPLE command ∙ The data transfer starts at the timing of DMARQ signal assertion At command issuance I/O registers setting contents3 READ DMA XC8 or XC9 In LBA modeAt command completion I/O registers contents to be read Error informationAt command issuance I/O registers setting contents 1F7 HSTAt command completion I/O registers contents to be read Error informationAt command issuance I/O registers setting contents 1F7 HSTAt command completion I/O registers contents to be read Error information1F7 HST Status informationAt command issuance I/O registers setting contents At command completion I/O registers contents to be readError information ∙ The data transfer starts at the timing of DMARQ signal assertionAt command issuance I/O registers setting contents At command completion I/O registers contents to be readError information 1 Single word DMA transfer modeAt command issuance I/O registers setting contents At command completion I/O registers contents to be readError information This command can be issued in the LBA modeAt command completion I/O registers contents to be read Error informationAt command issuance I/O registers setting contents At command completion I/O registers contents to be readAt command issuance I/O registers setting contents At command completion I/O registers contents to be readError Information 11 INITIALIZE DEVICE PARAMETERSAt command issuance I/O registers setting contents At command completion I/O registers contents to be readError information 1F7HCMTable 5.4 Information to be read by IDENTIFY DEVICE command 1 of C141-E034-02ENTable 5.4 Information to be read by IDENTIFY DEVICE command 2 of Table 5.4 Information to be read by IDENTIFY DEVICE command 3 of At command issuance I/O registers setting contents At command completion I/O registers contents to be readError information 14 SET FEATURES XEFTable 5.5 Features register values and settable modes X‘AA’PIO default transfer mode 00000X‘00’ PIO flow control transfer modeAt command issuance I/O registers setting contents At command completion I/O registers contents to be readError information 1F7HCMTable 5.6 Diagnostic code At command issuance I/O registers setting contents At command completion I/O registers contents to be readDiagnostic code The READ LONG command supports only single sector operationAt command issuance I/O registers setting contents At command completion I/O registers contents to be readError information This command is operated under the following conditionsAt command issuance I/O registers setting contents At command completion I/O registers contents to be readError information At command issuance I/O registers setting contentsAt command completion I/O registers contents to be read Error informationAt command issuance I/O registers setting contents At command completion I/O registers contents to be readPoint of timer Disable of timerAt command issuance I/O registers setting contents Period of timerAt command completion I/O registers contents to be read Error informationAt command issuance I/O registers setting contents At command completion I/O registers contents to be readAt command issuance I/O registers setting contents Period of timerAt command completion I/O registers contents to be read Error informationAt command issuance I/O registers setting contents At command completion I/O registers contents to be readError information This command is the only way to make the device enter the sleep modeAt command completion I/O registers contents to be read Error information27 CHECK POWER MODE X98 or XE5 The host checks the power mode of the device with this commandAt command issuance I/O registers setting contents At command completion I/O registers contents to be readError information 1F7 HCMTable 5.7 Features Register values subcommands and functions Features ResisterAt command issuance I-O registers setting contents SubcommandAt command completion I-O registers setting contents Error informationTable 5.8 Format of device attribute value data Format of insurance failure threshold value data Power-on time Number of power-on-power-off timesWrite error rate ∙ Attribute ID The attribute ID is defined as follows∙ Raw attribute value Raw attributes data is retained ∙ Failure prediction capability flagBits 2 to 15 Reserved bits ∙ Check sum ∙ Insurance failure threshold5.3.3 Error posting Table 5.10 Command code and parametersINDF ABRT5.4 Command Protocol 5.4.1 Data transferring commands from device to hostFigure 5.3 Read Sectors command protocol Figure 5.4 Protocol for command abort 5.4.2 Data transferring commands from host to deviceFigure 5.5 WRITE SECTORS command protocol 5.4.3 Commands without data transfer Figure 5.6 Protocol for the command execution without data transfer5.4.4 Other commands 5.4.5 DMA data transfer commandsFigure 5.7 Normal DMA data transfer 5.5 Ultra DMA feature set 5.5.1 Overview 5.5.2 Phases of operation 5.5.3 Ultra DMA data in commands5.5.3.1 Initiating an Ultra DMA data in burst 5.5.3.3 Pausing an Ultra DMA data in burst 5.5.3.2 The data in transfer5.5.3.4 Terminating an Ultra DMA data in burst b Host terminating an Ultra DMA data in burst C141-E034-02EN5.5.4 Ultra DMA data out commands 5.5.4.1 Initiating an Ultra DMA data out burst5.5.4.3 Pausing an Ultra DMA data out burst 5.5.4.2 The data out transfer5.5.4.4 Terminating an Ultra DMA data out burst b Device terminating an Ultra DMA data out burst C141-E034-02EN5.5.5 Ultra DMA CRC rules 5.5.6 Series termination required for Ultra DMA Table 5.11 Recommended series termination for Ultra DMAFigure 5.8 Ultra DMA termination with pull-up or pull-down 5.6 Timing 5.6.1 PIO data transfer C141-E034-02ENFigure 5.9 PIO data transfer timing 5.6.2 Single word DMA data transfer Figure 5.10 Single word DMA data transfer timing5.6.3 Multiword data transfer Figure 5.11 Multiword DMA data transfer timing mode5.6.4 Ultra DMA data transfer 5.6.4.1 Initiating an Ultra DMA data in burstFigure 5.12 Initiating an Ultra DMA data in burst 5.6.4.2 Ultra DMA data burst timing requirements Table 5.12 Ultra DMA data burst timing requirementstIORDYZ tZIORDYtACK 5.6.4.3 Sustained Ultra DMA data in burst Figure 5.13 Sustained Ultra DMA data in burst5.6.4.4 Host pausing an Ultra DMA data in burst Figure 5.14 Host pausing an Ultra DMA data in burst5.6.4.5 Device terminating an Ultra DMA data in burst Figure 5.15 Device terminating an Ultra DMA data in burst5.6.4.6 Host terminating an Ultra DMA data in burst Figure 5.16 Host terminating an Ultra DMA data in burst5.6.4.7 Initiating an Ultra DMA data out burst Figure 5.17 Initiating an Ultra DMA data out burst5.6.4.8 Sustained Ultra DMA data out burst Figure 5.18 Sustained Ultra DMA data out burst5.6.4.9 Device pausing an Ultra DMA data out burst Figure 5.19 Device pausing an Ultra DMA data out burst5.6.4.10 Host terminating an Ultra DMA data out burst Figure 5.20 Host terminating an Ultra DMA data out burst5.6.4.11 Device terminating an Ultra DMA data in burst Figure 5.21 Device terminating an Ultra DMA data out burst5.6.5 Power-on and reset Figure 5.22 Power-on Reset Timing6.1 Device Response to the Reset 6.2 Address Translation 6.3 Power Save 6.4 Defect Management 6.5 Read-Ahead Cache6.6 Write Cache 6.1 Device Response to the Reset OPERATIONS6.1.1 Response to power-on Figure 6.1 Response to power-on6.1.2 Response to hardware reset Figure 6.2 Response to hardware reset6.1.3 Response to software reset Figure 6.3 Response to software resetMaster device 6.1.4 Response to diagnostic command Figure 6.4 Response to diagnostic command6.2.1 Default parameters Default parameters6.2 Address Translation 6.2.2 Logical address Figure 6.5 Address translation example in CHS modeFigure 6.6 Address translation example in LBA mode 6.3 Power Save 6.3.1 Power save mode∙ Power-on sequence is completed ∙ A command other than power commands is issued∙ Reset hardware or software 2 Idle mode ∙ After completion of power-on sequence6.3.2 Power commands 6.4 Defect Management6.4.1 Spare area 6.4.2 Alternating defective sectorsFigure 6.7 Sector slip processing DefectiveFigure 6.8 Alternate cylinder assignment 6.5.1 Data buffer configuration Figure 6.9 Data buffer configuration6.5 Read-Ahead Cache 6.5.2 Caching operation 6.5.3 Usage of read segment 4 Following shows the cache enabled data for next read command Cache enabled dataHAP Segment only for read DAP Stores the read-requested data upto this pointa. Sequential command just after non-sequential command 3 Sequential readMis-hit data Empty dataHAP Read-ahead data DAP Last LBA Start LBA b. Sequential hit HAP Completion of transferring requested dataRead-ahead data Hit datac. Non-sequential read command just after sequential read command HAP Read-ahead data DAP4 Finally, the cache data in the buffer is as follows Read-ahead data Start LBALast position at previous read command DAP Last position at previous read command3 The cache data for next read command is as follows Cache data HAP set to hit position for data transferDAP stopped 3 The cache data for next read command is as follows Partially hit dataLack data Requested data to be transferred6.6 Write Cache When the write cache function is enabled, the transferred data from the host by the WRITE SECTORS is not completely written on the disk medium at the time that the interrupt of command complete is generated. When the unrecoverable error occurs during the write operation, the command execution is stopped. Then, when the drive receives the next command, it generates an interrupt of abnormal end. However an interrupt of abnormal end is not generated when a write automatic assignment succeeds. However, since the host may issue several write commands before the drive generates an interrupt of abnormal end, the host cannot recognize that the occurred error is for which command generally. Therefore, it is very hard to retry the unrecoverable write error for the host in the write cache operation generally. So, take care to use the write cache function Page 61-2-411-8603 FUJITSU LIMITED Reader Comment Form