Fujitsu RX600 instruction

Image 6

Fujitsu RX600 manual

Contents

Primergy RX600 S4 Server Comments… Suggestions… Corrections… Copyright and TrademarksCertified documentation according to DIN EN ISO Contents Contents Controls and indicators Incorrect date and time Page Preface Concept and target groups for this manual Documentation overview Documentation overview Preface Features Customer Self Service CSSFurther sources of information Hot-plug PCI slots Features PrefaceSystem board Hard disk drives Accessible drives/components Power supplyCooling RX600 S4 IRMC S2 with integrated service LAN port Features Preface Server management Service and support ServerStart Features Preface ServerView Remote Management Technical data Electrical data hot-plug power supply unitNotational conventions Technical data Compliance with regulations and standardsMechanical values Ambient conditions WeightVentilation clearance Noise levelPage Overview of the installation steps Overview of the installation steps Safety instructions Important information Safety instructions Installation and operationBefore starting up Important information Safety instructions Batteries Working with CDs/DVDs and CD/DVD drives Laser informationNever remove parts of the CD/DVD drive casing Modules with Electrostatic-Sensitive Devices ESD label CE conformity CE conformityOther important information FCC Class a Compliance Statement Transporting the server Transporting the server Operating manual Environmental protection Labels on plastic casing parts Returns, recycling and disposalPage Hardware installation Minimum acclimatization timeHours Unpacking the server Unpacking the server Rack requirements Rack installation/removal of serverHardware installation Primecenter Rack Rack installation/removal of server DataCenter Rack3rd party rack Mechanical requirements RX600 S4 Rack installation/removal of server Mounting in the Primecenter Rack Mounting the telescopic rails in the Primecenter Rack Installation in the DataCenter Rack Installation in 3rd party racks Inserting the server Inserting the server Following steps can then be carried out by one person only Rack installation/removal of serverHardware installation Securing the server Connecting devices to the server Ports on the front Connecting devices to the server Ports on the left side of the rear There are further ports at the rear right, see figure Connecting the server to the mains Connecting the server to the mains Connecting the monitor Securing the power cord in the cable clamp Connecting cables Disconnecting cables Controls and indicators Starting up and operationFront of server Controls Front overall view Indicators on the control panel Starting up and operation Controls and indicators CSS ServerView Local Service Display Indicators on the HDD modules Indicators on an HDD module Indicator on the fan modules Fan indicator Meaning LAN indicators Rear of server CSS indicator CSS indicator rear right Global Error indicator Global Error indicator rear right ID indicator and ID button ID indicator and ID button rear right Indicators on the hot-plug power supply units Indicators on the power supply units right power supply unit System already installed Switching the server on and offSwitching the server on Starting up for the first time Specified switch-on time/switch-off time Switching the server on and offSwitching the server off Ring Indicator Configuring the server Configuring onboard SAS RAID controller Configuration with ServerStart Configuring the serverServerStart advantages Configuring onboard SAS RAID controller Cleaning the serverConfiguration without ServerStart Installing the operating systemPage Mechanical access protection Bios Setup security functionsProperty and data protection Page Power cable incorrectly connected Troubleshooting and tipsPower-on indicator remains unlit Power supply overloaded Server switches itself off Screen remains blank No screen display or display drifts Troubleshooting and tipsFlickering stripes on monitor screen Monitor does not support the set horizontal frequency Incorrect date and time Drives reported as dead when starting systemRAID controller configuration incorrect Incorrect date and time Error message on screen RAID controller is not configured for this driveAdded drive reported as defective Page CSS components Replacing the hot-plug power supply unit Hot-plug componentsHot-plug components Unlocking and removing the power supply unit CSS components Replacing hot-plug CPU fans Unlocking fan module left and removing it Replacing hot-plug main memory fans Open the housing cover see Opening/closing the housing on Close the housing cover see Opening/closing the housing on Hot-plug hard disk drives Handling hard disk drives and HDD modules Removing/installing the dummy module Removing the dummy module Installing/removing the HDD module Unlocking the HDD module Unlocking the HDD module Installing the HDD module Pushing the HDD module into the slot Lock the HDD module Removing the HDD module Vcaution Hot-plug expansion cards Removing a hot-plug expansion card Slots with and without hot-plug functionality Deactivating, unlocking and removing the board Removing expansion card from the removal tool Removing the expansion card from the removal tool Removing engaging hooks Removing engaging hooks from the removal tool Removing a dummy module Removing the retaining plate from the removal tool Operating manual 103 Operating the expansion card Replacement of non-hot-plug components Replacing a memory module Replacement of non-hot-plug components Open the server see Opening/closing the housing on Removing the memory board in question Example Removing memory board a Removing the memory board cover Removing a defective memory module Identify the slot on the memory board Removing a memory module Installing a new memory module Inserting a memory module Reinstalling the memory board in question Placing the cover on the memory board Operating manual 113 Opening/closing the housing Opening/closing the housing Abbreviations Abbreviations EIA ICM LUN Abbreviations PS/2 RoHSRoMB Scsi Page Bios Index Index 91, 96 LAN Reset button Return of devices