Indicator on the fan modules, Fan indicator Meaning | Fujitsu RX600

Starting up and operation

Controls and indicators

5.1.1.5Indicator on the fan modules

1

Figure 16: Fan status indicator (right fan module)

The server has two fan modules each with two hot-plug system fans. The fan status indicator (1) visible at the front relates to both fans in a module.

Fan indicator	Meaning

does not light	Both fans in that fan module are OK.

lights orange	At least one fan is defective. That fan module has to be
	replaced (see “Replacing hot-plug CPU fans” on page 84).

RX600 S4

Operating manual

61

Image 61

Fujitsu RX600 manual Indicator on the fan modules, Fan indicator Meaning

Contents

Primergy RX600 S4 Server Copyright and Trademarks Comments… Suggestions… Corrections…Certified documentation according to DIN EN ISO Contents Controls and indicators Contents Incorrect date and time Page Concept and target groups for this manual Preface Documentation overview Preface Documentation overview Customer Self Service CSS FeaturesFurther sources of information System board Features PrefaceHot-plug PCI slots Hard disk drives Power supply Accessible drives/componentsCooling RX600 S4 IRMC S2 with integrated service LAN port Features Preface Server management ServerStart Service and support Features Preface ServerView Remote Management Electrical data hot-plug power supply unit Technical dataNotational conventions Compliance with regulations and standards Technical dataMechanical values Ventilation clearance WeightAmbient conditions Noise levelPage Overview of the installation steps Overview of the installation steps Important information Safety instructions Installation and operation Safety instructionsBefore starting up Important information Safety instructions Batteries Laser information Working with CDs/DVDs and CD/DVD drivesNever remove parts of the CD/DVD drive casing ESD label Modules with Electrostatic-Sensitive Devices CE conformity CE conformityOther important information FCC Class a Compliance Statement Transporting the server Transporting the server Operating manual Environmental protection Returns, recycling and disposal Labels on plastic casing partsPage Minimum acclimatization time Hardware installationHours Unpacking the server Unpacking the server Hardware installation Rack installation/removal of serverRack requirements Primecenter Rack DataCenter Rack Rack installation/removal of server3rd party rack Mechanical requirements RX600 S4 Rack installation/removal of server Mounting in the Primecenter Rack Mounting the telescopic rails in the Primecenter Rack Installation in 3rd party racks Installation in the DataCenter Rack Inserting the server Inserting the server Following steps can then be carried out by one person only Securing the server Rack installation/removal of serverHardware installation Ports on the front Connecting devices to the server Ports on the left side of the rear Connecting devices to the server There are further ports at the rear right, see figure Connecting the server to the mains Connecting the server to the mains Securing the power cord in the cable clamp Connecting the monitor Disconnecting cables Connecting cables Starting up and operation Controls and indicatorsFront of server Front overall view Controls Starting up and operation Indicators on the control panel CSS Controls and indicators ServerView Local Service Display Indicators on an HDD module Indicators on the HDD modules Fan indicator Meaning Indicator on the fan modules Rear of server LAN indicators CSS indicator rear right CSS indicator Global Error indicator rear right Global Error indicator ID indicator and ID button rear right ID indicator and ID button Indicators on the power supply units right power supply unit Indicators on the hot-plug power supply units Switching the server on Switching the server on and offSystem already installed Starting up for the first time Switching the server off Switching the server on and offSpecified switch-on time/switch-off time Ring Indicator Configuring onboard SAS RAID controller Configuring the server Configuring the server Configuration with ServerStartServerStart advantages Configuration without ServerStart Cleaning the serverConfiguring onboard SAS RAID controller Installing the operating systemPage Bios Setup security functions Mechanical access protectionProperty and data protection Page Power-on indicator remains unlit Troubleshooting and tipsPower cable incorrectly connected Power supply overloaded Screen remains blank Server switches itself off Flickering stripes on monitor screen Troubleshooting and tipsNo screen display or display drifts Monitor does not support the set horizontal frequency RAID controller configuration incorrect Drives reported as dead when starting systemIncorrect date and time Incorrect date and time RAID controller is not configured for this drive Error message on screenAdded drive reported as defective Page CSS components Hot-plug components Replacing the hot-plug power supply unitHot-plug components CSS components Unlocking and removing the power supply unit Replacing hot-plug CPU fans Unlocking fan module left and removing it Replacing hot-plug main memory fans Open the housing cover see Opening/closing the housing on Close the housing cover see Opening/closing the housing on Hot-plug hard disk drives Handling hard disk drives and HDD modules Removing the dummy module Removing/installing the dummy module Unlocking the HDD module Installing/removing the HDD module Unlocking the HDD module Pushing the HDD module into the slot Installing the HDD module Lock the HDD module Removing the HDD module Vcaution Hot-plug expansion cards Slots with and without hot-plug functionality Removing a hot-plug expansion card Deactivating, unlocking and removing the board Removing the expansion card from the removal tool Removing expansion card from the removal tool Removing engaging hooks from the removal tool Removing engaging hooks Removing the retaining plate from the removal tool Removing a dummy module Operating manual 103 Operating the expansion card Replacing a memory module Replacement of non-hot-plug components Open the server see Opening/closing the housing on Replacement of non-hot-plug components Example Removing memory board a Removing the memory board in question Removing the memory board cover Identify the slot on the memory board Removing a defective memory module Removing a memory module Inserting a memory module Installing a new memory module Placing the cover on the memory board Reinstalling the memory board in question Operating manual 113 Opening/closing the housing Opening/closing the housing Abbreviations Abbreviations EIA ICM LUN RoHS Abbreviations PS/2RoMB Scsi Page Index Bios 91, 96 Index LAN Reset button Return of devices