Test Run, To test run the machine | Grizzly G0651, G0652 manual

Test Run

Once the assembly is complete, test run your machine to make sure it runs properly for regular operations.

The test run consists of verifying the following:

1)The motor powers up and runs correctly, 2) the safety disabling mechanism on the switch works correctly, and 3) the saw operates without unusual noises or vibration.

If, during the test run, you cannot easily locate the source of an unusual noise or vibration, stop using the machine immediately, then review the Troubleshooting on Page 47.

If you still cannot remedy a problem, contact our Tech Support at (570) 546-9663 for assistance.

To test run the machine:

1.Read this manual and make sure you under- stand SECTION 1: SAFETY on Page 8.

2.Review Circuit Requirements on Page 13, double check your work, and make any necessary changes.

3.Make sure the blade guard and splitter (or riv- ing knife) are installed and correctly adjusted, and verify that the blade is secured by the arbor nut.

4.Remove all tools and foreign objects from the machine.

5.Connect the tablesaw to the power source.

6.Put on safety glasses and hearing protection, and make sure any bystanders are wearing safety glasses, hearing protection, and are out of the way.

7.Make sure the safety pin is not installed.

-28-

8.Verify that the machine is operating cor- rectly by pressing the ON button.

—If the saw is operating normally, press the STOP paddle. This should stop the saw.

—If any problems occur, immediately press the STOP paddle and DISCONNECT THE SAW FROM THE POWER SOURCE. Turn to Troubleshooting on Page 47 and correct the problem before starting the table saw again.

—If you cannot easily locate the source of an unusual noise or vibration by yourself, please contact Technical Support at (570) 546-9663.

9.Lift the paddle switch and insert the safety pin through the ON button.

10.Press the ON button.

—If the saw does not start, the safety dis- abling feature is working correctly.

—If the saw starts, immediately press the OFF button and DISCONNECT THE SAW FROM THE POWER SOURCE. The safety disabling feature is not working correctly. Please contact our Technical Support at

(570)546-9663 immediately.

G0651/G0652 10" Extreme Series Table Saws

Image 30

Grizzly G0651, G0652 owner manual Test Run, To test run the machine

Contents

Extreme Series Table Saws Ss ,EAD from Leadbased PAINTS Table of Contents Contact Info IntroductionForeword Functional Overview #.% $!4 #ONSTRUCTION $%,$ %842%-%23%2%3 4!,% G0651/G0652 10 Extreme Series Table Saws Identification G0651 Identification !,7!93 53% !.3 !002/6%$$ 3!&%49 ,!33%33 7%. /0%2!4 !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%29 -!.9 -!#.%3 #!. %*%#4 7/2+0%#%3 4/7!2$ /0%2!4/2 53%3!!2/5.$%$ %84%.3/..#/2$ 2!4%$4&/2/4%-!#.%!-0%2!%2 53%3 2%#/--%.$%$- !##%33/2%3 !,7!93 ,/#+ -/,% !3%3 & 53%$ % %&/2% /0%2!4. -!#.%29# Safety Instructions for Table Saws Preventing Kickback Protecting Yourself From KickbackBelow are tips to avoid the most common causes of kickback Glossary of Terms Circuit Requirements Model G0651 Operation Minimum Cord Requirements Phase Converter PrecautionModel G0652 220/440V Operation Full Load Amp Draw 440V Conversion Items Needed for Setup SetupSetup Safety Unpacking Fence InventoryTable Saw Unit Fence Rail Extension Table Outfeed Table Hardware Recognition Chart Site Considerations Clean UpPlacement Location Floor Load Assembly To assemble the extension table and outfeed tablesPage Page Saw Blade To install the bladeTo install the blade guard Blade Guard Splitter Riving Knife Table Insert To install the riving knifeTo install and adjust the table insert Insert On/Off Switch Miter Gauge Fence Components Dust Collection To connect a dust collection hose Test Run To test run the machine Incoming Power Wires Contactor Operation Safety Basic Controls Operations Ripping blade features Crosscut blade featuresBlade Selection Combination blade features Laminate blade featuresDado Blades Non-Through Cuts Workpiece InspectionNon-Through Through Cuts Through Cuts Ripping Typical ripping operation To make a crosscut using the miter gauge Crosscutting Miter CutsTo perform a miter cut Using a Stacked or Wobble Dado Blade Blade Tilt/Bevel CutsDado Cutting Using a Standard Saw Blade to Cut Dadoes Rabbet Cutting Cutting Rabbets with Dado Blade Cuting Rabbets with Standard Blade Rabbet cutting with a standard blade Resawing Resaw Barrier Auxiliary Fence Resawing Operations Components Needed for Resawing GZhVl ZcXZ 7VggZg $ -8dccZXidc H7583-Grizzly Tenoning Jig AccessoriesT20646-Zero Clearance Insert for G0651/ G0652 H9587-Table Saw Fundamentals G0638 10HP Cyclone Dust Collector G7581-Superbar G7582-Master Plate Schedule MaintenanceCleaning Lubrication Service TroubleshootingMotor & Electrical Table Saw Operations Replacing Flat Belt Removing Flat BeltTools Needed Qty Installing New Belt Blade Tilt Stops Setting 90 Stop BoltSetting 45 Stop Bolt Step Adjusting Tilt Indicator Arrow To adjust the table tilt gear backlashTable Tilt Handwheel Backlash Miter Slot to Blade Parallelism To adjust the blade parallel to the miter slotDigital Readout To set the digital readout Shim procedure diagram a Blade Alignment Adjusting FenceTo adjust the blade alignment by moving the table Square and Height Clamping Pressure and Parallelism Wrench 8mm Wiring Electrical Safety Instructions G0651/G0652 Electrical Components G0651 motor junction box G0651 Wiring Diagram 220V, 1-Ph See FigureHLI8= See Figure G0652 magnetic switch prewired to 220V, 3-phase G0652 Electrical Components G0652 Wiring Diagram 220V, 3-Ph Motor Direction G0652 Wiring Diagram 440V, 3-Ph 440 VAC Parts Motor and Arbor Breakdown Motor and Arbor Parts List Description G0651 3HP, 220V, 1-PHASE Switch Cabinet Breakdown Cabinet Parts List Description Blade Guard Breakdown Fence Assembly Breakdown Miter Gauge Breakdown Extension Table Breakdown Outfeed Table Breakdown Label Placement 22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!- 7! WARRANTY7!22!.499!AND.$$2%452RETURNS.3 #ALL 4ODAYD&ORO! &2%%