Managing The Adsl Router | Heritage Kayaks Heritage Series guide

4.2 Enables NAT to RFC1483, Classic IP (RFC1577), PPP over

	ATM (RFC2364) and PPP over Ethernet (RFC2516) in
	Routing mode	44
4.3 Changing DHCP server configuration		46
4.4	Changing DHCP client configuration	49
4.5	PPTP Tunneling Configuration	51

Chapter 5 Managing The ADSL Router	55
5.1 Booting the ADSL Router
from Ethernet Network	55
5.2 Upgrading on-board flash memo
from Ethernet network	56
5.3 SNMP	57
Chapter 6 ADSL Link Performance Statistics	59
Chapter 7 Command Sets for Command Line
Interface	61
Command Line Interface Conventions	61
Basic system command sets	62
Commands for ISFS and FLASHFS process	65
Commands for Bridge process	67
Commands for DHCP server process	76
Commands for DHCP client process	78
Commands for IP process	80
Commands for NAT process	98
Commands for PPP process	102
Commands for SNMP process	112
Commands for ADSL process	114
Chapter 8 DHCP Server Operation	117
8.1 DHCP Server Overview	117
8.2 DHCP Server Configuration	118
8.3 Informal configuration guide	118

Image 4

Heritage Kayaks Heritage Series manual Managing The Adsl Router

Contents

Heritage Series Copyright Table of Contents Managing The Adsl Router Dhcp Client Configuration 135 Chapter Overview Features and Compatibility Heritage Series Adsl Bridge/ Router Introduction What’s in the package? Important Rules for Safe Operation Do Not place Near High Temperature Source For example near Turn Off the Power Switch Between DC Plug Off and On Heritage Series Adsl Bridge/ Router Introduction Front Panel Function Behavior Definition Rear Panel Function Definition 10Introduction Installing Configuring your Adsl Router Preparation for Hardware and software installation DSLAM/ISP PC a HUB Hardware Installation Check TCP/IP protocol Windows 95/98 setting for Ethernet LAN connectionDouble-click on My computer-Control Panel-Network Installing and Configuring your Adsl Router 2 TCP/IP installation Page 3 TCP/IP setting Your network manager for correct configurations Installing and Configuring your Adsl Router For example Click OK to save the new setting Using Telnet via Ethernet interface Configuring the RouterSelect Start-Programs-MS-DOS Prompt Using terminal program via serial console port Select Start-Programs-Accessories-HyperTerminalPage Installing and Configuring your Adsl Router Installing and Configuring your Adsl Router Basic Configurations Factory default configuration DSL Bridged RFC1483 Default configuration for Router System configurationISP/DSLAM configuration Local PC configuration Isfs rm resolve Isfs rm initbridge Isfs rm initppp Restart Local PC B configuration Local PC a configurationRouted RFC1483 Is the IP address of your service provider Classical IP RFC1577 Basic Configurations Use the same VPI/VCI of RFC 1577 setting This is the login name and password of PPP server PPP Over ATM RFC2364 Remote bridging over PPPoA Basic Configurations Basic Configurations PPP Over Ethernet RFC2516 Ip relay all Config save Restart Advanced Configurations Local PC 8 configuration Local PC 1 configurationAdd NAT to Classic IP, PPP over ATM or PPP over Ethernet Ip nat add ipoa 192.168 Add NAT to RFC 1483 to above RFC 1483 Routing Mode example Changing Dhcp server configuration Deletes current Dhcp server settings Restart Home Dhcpclient config Changing Dhcp client configurationDhcpclient config flush Dhcpclient config confirm Pptp Tunneling Configuration Set channel 2 to VPI=0, VCI=32 Set channel 2 to VPI=0, VCI=32 Pptp bind none Config save Restart Advanced Configurations Booting the Adsl Router from Ethernet Network Router Configuration This command is available for update boot code only Upgrading on-board flash memory from Ethernet network Snmp PPP/IP MIB RFC Managing The Adsl Router Adsl Link Performance Statistics Adsl Link Performance Statistics Command Sets for Command Line Interface Command line interface conventions Basic system command sets Process, process command Help DSL conifg Restart History mechanismSystem Isfs and Flashfs overview Commands for Isfs and Flashfs processIsfs cat flashfs cat Isfs ls flashfs ls Flashfs updateIsfs rm Commands for Bridge process Device addDevice delete Forum LAN emulation alecjade Device list Ethertype Filterage FilterFlush Portfilter Spanning forwarddelay Spanning disable enableStatus Spanning hellotime Spanning maxage Spanning port number Spanning port number disabled enableSpanning port number pathcost Spanning port number priority Spanning priority Spanning status Commands for Dhcp server process Dhcpserver config DSL dhcpserver config Dhcpserver status IP address Client UID Expiry Commands for Dhcp Client process Dhcpclient config Dhcpclient status Ip device …DHCP then discovers the IP address for the interface… Commands for IP process Arp Config DSL ip config Device Ethernet Disable Enable Ipatm abort GetIpatm arp Ipatm arpserver Ipatm files Ipatm lifetime Ipatm pvc Iphostname Norelay Ping Portname Command Relay Rip accept Rip allowed Rip bootRip hostroutes Rip poison Rip killrelayRip relay Rip send Rip relaysRoute Example Routes RouteflushStats Subnet Commands for NAT process Ip natNat interfaces Nat inbound Nat info Nat inbound add pppdevice 80/TCP Nat inbound list Nat protocol Nat sessions Nat stats Nat sessions ppp Commands for PPP process Console object types Channel disable Channel echo every Channel lcpmaxconfigure Channel lcpmaxfailure Channel lcpmaxterminate Channel llc Read PVC settings for channel Remove any PVC settings fromSet channel 3 to be VPI=3,VCI=32 Channel Channel remoteip Channel theylogin Bcp Interface n localip Interface n stats User Commands for Snmp configuration Access Trap Commands for Adsl process Mode multi Show errorShow perf 10. up 116 Command Sets for Command Line Interface Dhcp Server Operation Dhcp Server overview Informal configuration guide Dhcp Server ConfigurationSubnets Bootp Support Lease Length Configuration reference guide Options Network topology Subnet DeclarationsRange Allow and Deny HostGroup Unknown-clients Parameters Dynamic-bootp-lease-cutoff FilenameServer-name Next-server Dynamic-bootp-lease-length Use-host-decl-names Option statements Server-identifier 128 129 130 131 132 133 134 Dhcp Server Operation Chapter Dhcp Client Timeout Select-timeoutProtocol Timing Retry Reboot Backoff-cutoffInitial-interval Lease requirements and requests Request RequireSend Other declarations Reject Interface Dhcp Options 140 Supported Dhcp client options 142 Dhcp Client Configuration Appendix a Product Specifications Appendix Power Adaptor If the Power LED is dark Diagnostics with the LEDsIf the PC LED is dark Problems when configure the Modem via the console port Problems when connecting to the Modem via EthernetCan’t see any message from the configuration screen Junk characters appear on the configuration screen Problems when accessing the Internet or remote network Cant’s access the Internet or remote networkIf the Modem is configured to bridging mode If the Modem is configured to routing mode Contact us for Technical support Ansi American National Standards Institute 10Base-TBridge Class A, B, and C networks ClientCommunity strings Console port Ethernet address FirmwareInternet Internet address, IP address MAC layer/address PingPort number Protocol A12 RFCRJ-11 RJ-45 Routing table Serial portServer Subnet Address Transparent Bridging Virtual ChannelVirtual Path Wall jack Appendix D Government compliance notices FCC compliance DOC compliance information European CTR 21 compliance