Basic Configurations | Heritage Kayaks Heritage Series guide

34		Basic Configurations
	(use the same VPI/VCI of RFC 1577 setting)
	>	config save ↵
	>	restart ↵

Remove all existing IP module configuration device

>home ↵

>ip device flush ↵

>config save ↵

>restart ↵

We are ready for RFC1577 setup

Specify the gateway (RFC1577 on ISP/DSLAM site and Ethernet on local PC site)

>home ↵

>ip device add ethernet ether //edd 202.1.136.254 ↵

>ip device add ipoa atm //atm 192.168.1.2 ↵

>config save ↵

>restart ↵

Enable forwarding between router interface

>home ↵

>ip relay all ↵

>ip ipatm pvc add ipoa r1483 x/y remoteip 192.168.1.1 ↵

(‘ x’ is the VPI, ‘ y’ is the VCI. Check with your service provider)

>config save ↵

>restart ↵

Image 39

Heritage Kayaks Heritage Series manual Basic Configurations, Use the same VPI/VCI of RFC 1577 setting

Contents

Heritage Series Copyright Table of Contents Managing The Adsl Router Dhcp Client Configuration 135 Overview Chapter Features and Compatibility Heritage Series Adsl Bridge/ Router Introduction What’s in the package? Important Rules for Safe Operation Turn Off the Power Switch Between DC Plug Off and On Do Not place Near High Temperature Source For example near Heritage Series Adsl Bridge/ Router Introduction Function Behavior Definition Front Panel Function Definition Rear Panel 10Introduction Installing Configuring your Adsl Router DSLAM/ISP Preparation for Hardware and software installation PC a HUB Hardware Installation Windows 95/98 setting for Ethernet LAN connection Check TCP/IP protocolDouble-click on My computer-Control Panel-Network Installing and Configuring your Adsl Router 2 TCP/IP installation Page Your network manager for correct configurations 3 TCP/IP setting Installing and Configuring your Adsl Router For example Click OK to save the new setting Configuring the Router Using Telnet via Ethernet interfaceSelect Start-Programs-MS-DOS Prompt Select Start-Programs-Accessories-HyperTerminal Using terminal program via serial console portPage Installing and Configuring your Adsl Router Installing and Configuring your Adsl Router Basic Configurations DSL Factory default configuration Local PC configuration Bridged RFC1483 Default configuration for RouterSystem configuration ISP/DSLAM configuration Isfs rm resolve Isfs rm initbridge Isfs rm initppp Restart Local PC a configuration Local PC B configurationRouted RFC1483 Is the IP address of your service provider Classical IP RFC1577 Use the same VPI/VCI of RFC 1577 setting Basic Configurations PPP Over ATM RFC2364 This is the login name and password of PPP server Remote bridging over PPPoA Basic Configurations Basic Configurations PPP Over Ethernet RFC2516 Ip relay all Config save Restart Advanced Configurations Local PC 1 configuration Local PC 8 configurationAdd NAT to Classic IP, PPP over ATM or PPP over Ethernet Ip nat add ipoa 192.168 Add NAT to RFC 1483 to above RFC 1483 Routing Mode example Changing Dhcp server configuration Deletes current Dhcp server settings Restart Changing Dhcp client configuration Home Dhcpclient configDhcpclient config flush Dhcpclient config confirm Set channel 2 to VPI=0, VCI=32 Pptp Tunneling Configuration Set channel 2 to VPI=0, VCI=32 Pptp bind none Config save Restart Advanced Configurations Router Configuration Booting the Adsl Router from Ethernet Network Upgrading on-board flash memory from Ethernet network This command is available for update boot code only PPP/IP MIB RFC Snmp Managing The Adsl Router Adsl Link Performance Statistics Adsl Link Performance Statistics Command line interface conventions Command Sets for Command Line Interface Process, process command Basic system command sets DSL conifg Help History mechanism RestartSystem Commands for Isfs and Flashfs process Isfs and Flashfs overviewIsfs cat flashfs cat Flashfs update Isfs ls flashfs lsIsfs rm Forum LAN emulation alecjade Commands for Bridge processDevice add Device delete Ethertype Device list Filter FilterageFlush Portfilter Spanning disable enable Spanning forwarddelayStatus Spanning maxage Spanning hellotime Spanning port number disabled enable Spanning port numberSpanning port number pathcost Spanning priority Spanning port number priority Spanning status DSL dhcpserver config Commands for Dhcp server process Dhcpserver config IP address Client UID Expiry Dhcpserver status Dhcpclient status Commands for Dhcp Client process Dhcpclient config …DHCP then discovers the IP address for the interface… Ip device Arp Commands for IP process DSL ip config Config Device Ethernet Enable Disable Get Ipatm abortIpatm arp Ipatm files Ipatm arpserver Ipatm pvc Ipatm lifetime Norelay Iphostname Portname Ping Relay Command Rip accept Rip boot Rip allowedRip hostroutes Rip killrelay Rip poisonRip relay Rip relays Rip sendRoute Example Routeflush RoutesStats Subnet Nat inbound Commands for NAT processIp nat Nat interfaces Nat inbound add pppdevice 80/TCP Nat inbound list Nat info Nat sessions Nat protocol Nat sessions ppp Nat stats Console object types Commands for PPP process Channel disable Channel echo every Channel lcpmaxfailure Channel lcpmaxconfigure Channel llc Channel lcpmaxterminate Channel Read PVC settings for channelRemove any PVC settings from Set channel 3 to be VPI=3,VCI=32 Channel remoteip Channel theylogin Interface n localip Bcp User Interface n stats Access Commands for Snmp configuration Trap Commands for Adsl process 10. up Mode multiShow error Show perf 116 Command Sets for Command Line Interface Dhcp Server overview Dhcp Server Operation Dhcp Server Configuration Informal configuration guideSubnets Lease Length Bootp Support Options Configuration reference guide Network topology Declarations SubnetRange Unknown-clients Allow and DenyHost Group Parameters Next-server Dynamic-bootp-lease-cutoffFilename Server-name Use-host-decl-names Dynamic-bootp-lease-length Server-identifier Option statements 128 129 130 131 132 133 134 Dhcp Server Operation Chapter Dhcp Client Retry TimeoutSelect-timeout Protocol Timing Lease requirements and requests RebootBackoff-cutoff Initial-interval Other declarations Reject RequestRequire Send Dhcp Options Interface 140 Supported Dhcp client options 142 Dhcp Client Configuration Appendix a Product Specifications Appendix Power Adaptor Diagnostics with the LEDs If the Power LED is darkIf the PC LED is dark Junk characters appear on the configuration screen Problems when configure the Modem via the console portProblems when connecting to the Modem via Ethernet Can’t see any message from the configuration screen If the Modem is configured to routing mode Problems when accessing the Internet or remote networkCant’s access the Internet or remote network If the Modem is configured to bridging mode Contact us for Technical support 10Base-T Ansi American National Standards InstituteBridge Console port Class A, B, and C networksClient Community strings Internet address, IP address Ethernet addressFirmware Internet Protocol MAC layer/addressPing Port number RJ-45 A12RFC RJ-11 Subnet Address Routing tableSerial port Server Wall jack Transparent BridgingVirtual Channel Virtual Path FCC compliance Appendix D Government compliance notices DOC compliance information European CTR 21 compliance