Pptp Tunneling Configuration | Heritage Kayaks Heritage Series

Heritage Series ADSL Bridge/ Router	51
Advanced Configurations

4.5 PPTP Tunneling Configuration

The ADSL Router can be configured to supports PPTP as following procedure. But the ADSL Router currently provides the PPTP Access Concentrator (PAC) end of a PPTP tunnel. And the PC must run an OS, which supports PPTP, providing a PPTP Network Server (PNS). Both Win 98 and Win 2000 provide

•PPTP dial out

In the following example, the PC connects to the ADSL modem firstly must be configured as:

IP address of PNS	: 192.168.10.1
Subnet mask of PNS	: 255.255.255.0
Gateway of PNS	: 192.168.10.2
IP address of PAC	: 192.168.10.2

>ip device add Ethernet ether //edd 192.168.10.2 ↵

>config save ↵

>restart ↵

>ppp 2 pvc 0 32 ↵

(Set channel 2 to VPI=0, VCI=32)

>ppp 2 interface 0 ↵

>ppp 2 tunnel 1 pptp out ↵

>ppp 2 enable ↵

>pptp bind 192.168.10.2 ↵

>pptp 1 create listen ↵

>config save ↵

>restart ↵

Image 56

Heritage Kayaks Heritage Series manual Pptp Tunneling Configuration, Set channel 2 to VPI=0, VCI=32

Contents

Heritage Series Copyright Table of Contents Managing The Adsl Router Dhcp Client Configuration 135 Chapter Overview Features and Compatibility Heritage Series Adsl Bridge/ Router Introduction What’s in the package? Important Rules for Safe Operation Do Not place Near High Temperature Source For example near Turn Off the Power Switch Between DC Plug Off and On Heritage Series Adsl Bridge/ Router Introduction Front Panel Function Behavior Definition Rear Panel Function Definition 10Introduction Installing Configuring your Adsl Router Preparation for Hardware and software installation DSLAM/ISP PC a HUB Hardware Installation Double-click on My computer-Control Panel-Network Windows 95/98 setting for Ethernet LAN connectionCheck TCP/IP protocol Installing and Configuring your Adsl Router 2 TCP/IP installation Page 3 TCP/IP setting Your network manager for correct configurations Installing and Configuring your Adsl Router For example Click OK to save the new setting Select Start-Programs-MS-DOS Prompt Configuring the RouterUsing Telnet via Ethernet interface Using terminal program via serial console port Select Start-Programs-Accessories-HyperTerminalPage Installing and Configuring your Adsl Router Installing and Configuring your Adsl Router Basic Configurations Factory default configuration DSL Bridged RFC1483 Default configuration for Router System configurationISP/DSLAM configuration Local PC configuration Isfs rm resolve Isfs rm initbridge Isfs rm initppp Restart Routed RFC1483 Local PC a configurationLocal PC B configuration Is the IP address of your service provider Classical IP RFC1577 Basic Configurations Use the same VPI/VCI of RFC 1577 setting This is the login name and password of PPP server PPP Over ATM RFC2364 Remote bridging over PPPoA Basic Configurations Basic Configurations PPP Over Ethernet RFC2516 Ip relay all Config save Restart Advanced Configurations Add NAT to Classic IP, PPP over ATM or PPP over Ethernet Local PC 1 configurationLocal PC 8 configuration Ip nat add ipoa 192.168 Add NAT to RFC 1483 to above RFC 1483 Routing Mode example Changing Dhcp server configuration Deletes current Dhcp server settings Restart Dhcpclient config flush Changing Dhcp client configurationHome Dhcpclient config Dhcpclient config confirm Pptp Tunneling Configuration Set channel 2 to VPI=0, VCI=32 Set channel 2 to VPI=0, VCI=32 Pptp bind none Config save Restart Advanced Configurations Booting the Adsl Router from Ethernet Network Router Configuration This command is available for update boot code only Upgrading on-board flash memory from Ethernet network Snmp PPP/IP MIB RFC Managing The Adsl Router Adsl Link Performance Statistics Adsl Link Performance Statistics Command Sets for Command Line Interface Command line interface conventions Basic system command sets Process, process command Help DSL conifg System History mechanismRestart Isfs cat flashfs cat Commands for Isfs and Flashfs processIsfs and Flashfs overview Isfs rm Flashfs updateIsfs ls flashfs ls Commands for Bridge process Device addDevice delete Forum LAN emulation alecjade Device list Ethertype Flush FilterFilterage Portfilter Status Spanning disable enableSpanning forwarddelay Spanning hellotime Spanning maxage Spanning port number pathcost Spanning port number disabled enableSpanning port number Spanning port number priority Spanning priority Spanning status Commands for Dhcp server process Dhcpserver config DSL dhcpserver config Dhcpserver status IP address Client UID Expiry Commands for Dhcp Client process Dhcpclient config Dhcpclient status Ip device …DHCP then discovers the IP address for the interface… Commands for IP process Arp Config DSL ip config Device Ethernet Disable Enable Ipatm arp GetIpatm abort Ipatm arpserver Ipatm files Ipatm lifetime Ipatm pvc Iphostname Norelay Ping Portname Command Relay Rip accept Rip hostroutes Rip bootRip allowed Rip relay Rip killrelayRip poison Route Rip relaysRip send Example Stats RouteflushRoutes Subnet Commands for NAT process Ip natNat interfaces Nat inbound Nat info Nat inbound add pppdevice 80/TCP Nat inbound list Nat protocol Nat sessions Nat stats Nat sessions ppp Commands for PPP process Console object types Channel disable Channel echo every Channel lcpmaxconfigure Channel lcpmaxfailure Channel lcpmaxterminate Channel llc Read PVC settings for channel Remove any PVC settings fromSet channel 3 to be VPI=3,VCI=32 Channel Channel remoteip Channel theylogin Bcp Interface n localip Interface n stats User Commands for Snmp configuration Access Trap Commands for Adsl process Mode multi Show errorShow perf 10. up 116 Command Sets for Command Line Interface Dhcp Server Operation Dhcp Server overview Subnets Dhcp Server ConfigurationInformal configuration guide Bootp Support Lease Length Configuration reference guide Options Network topology Range DeclarationsSubnet Allow and Deny HostGroup Unknown-clients Parameters Dynamic-bootp-lease-cutoff FilenameServer-name Next-server Dynamic-bootp-lease-length Use-host-decl-names Option statements Server-identifier 128 129 130 131 132 133 134 Dhcp Server Operation Chapter Dhcp Client Timeout Select-timeoutProtocol Timing Retry Reboot Backoff-cutoffInitial-interval Lease requirements and requests Request RequireSend Other declarations Reject Interface Dhcp Options 140 Supported Dhcp client options 142 Dhcp Client Configuration Appendix a Product Specifications Appendix Power Adaptor If the PC LED is dark Diagnostics with the LEDsIf the Power LED is dark Problems when configure the Modem via the console port Problems when connecting to the Modem via EthernetCan’t see any message from the configuration screen Junk characters appear on the configuration screen Problems when accessing the Internet or remote network Cant’s access the Internet or remote networkIf the Modem is configured to bridging mode If the Modem is configured to routing mode Contact us for Technical support Bridge 10Base-TAnsi American National Standards Institute Class A, B, and C networks ClientCommunity strings Console port Ethernet address FirmwareInternet Internet address, IP address MAC layer/address PingPort number Protocol A12 RFCRJ-11 RJ-45 Routing table Serial portServer Subnet Address Transparent Bridging Virtual ChannelVirtual Path Wall jack Appendix D Government compliance notices FCC compliance DOC compliance information European CTR 21 compliance