Honeywell MKXXII installation manual Table E Non-Integrated Efis 40/50 Honeywell/Bendix

Honeywell

MK XXII EGPWS Installation Manual

Table E 3.1.6-9	Non-Integrated EFIS 40/50 (Honeywell/Bendix)
	DISPLAY CONFIGURATION GROUP 7 (NON-INTEGRATED EFIS 40/50)

Function

Display Type

Sweep Type

Auto Pop Up

Value

Bendix Non-Integrated EFIS 40/50

Sweep range +/- 60 degrees

Category 7, Options Select Group #1

TA&D Alternate Pop Up: False	TA&D Alternate Pop Up: True
Pop Up when display is in the	Never Pop Up
proper mode.

Peaks Mode (Peaks Elevations are in Terrain Image, replacing “TERR”)

Manual select

Manual deselect

Auto Range

Moving Marker

Overlay Page

Display bus type

DISPLAY BUS #1 453TX_1

A= J1-58

B= J1-59

Category 7, Options Select Group #1

Peaks Enabled: False	Peaks Enabled: True
Peaks Off	Peaks On

Anytime WXR is on and display is in proper Mode

Anytime

No

No

Yes; “TERR” at upper right corner of display.

Standard ARINC 453

CONNECT TO:

Terrain Display data to switching relay/Symbol Generator

DISPLAY BUS #2 453TX_2

A= J1-56

B= J1-57

CONNECT TO:

Terrain Display data to switching relay/Symbol Generator

DISPLAY INPUT CONTROL GROUP 2

CHANNEL 429_422RX_1

A= J2-37

B= J2-36

CHANNEL 429RX_3

CONNECT TO: WX-IND 429 out (range) Bus 1 (Low Speed)

Data

Mode (Display Word 1)

Range (Display Word 2)

Discrete Word (VP)

CONNECT TO: WX-IND 429 out (range) Bus 2 (Low Speed)

Fault Designation: DISPLAY BUS 1

Bus Type: Basic

Label	Sig. Bits	Range	Signal Type	Resolution	Rate
270	Discrete	Mode, Tilt, Gain	Basic	N/A	100 ms
271	Discrete	5-320NM	Basic	N/A	100 ms
273	Discrete	VP Mode, Bit 11	Basic	N/A	100 ms

Fault Designation: DISPLAY BUS 2

Bus Type: Basic

A= J2-41

B= J2-40

CONN PIN #

J1-32

J1-31

Data

Mode (Display Word 1)

Range (Display Word 2)

Discrete Word (VP)

REFERENCE NAME

GND_DISC_12

GND_DISC_13

Label	Sig. Bits	Range
270	Discrete	Mode, Tilt, Gain
271	Discrete	5-320NM
273	Discrete	VP Mode, Bit 11

PIN FUNCTION

Display Select Discrete #1

Display Select Discrete #2

OUTPUT 429 BUS GROUP 0

Signal Type	Resolution	Rate
Basic	N/A	100 ms
Basic	N/A	100 ms
Basic	N/A	100 ms

Polarity/Configuration

Type 1 (Momentary)

Gnd = Display Select Toggle <not> Gnd = Normal

Type 1 (Momentary)

Gnd = Display Select Toggle <not> Gnd = Normal

Channel

429TX_1 (Low Speed)

429TX_2

Pins

A = J2-43 B = J2-42

A = J2-26 B = J2-9

Comments

Transmits (Section 7) Label sets: 7.1.1.x, 7.1.2.x, 7.1.3.x and 7.1.4.x

No Connection (No Data Output)

Integration note:

When interfacing to a single display controller configuration the bus must be connected to both EGPWS input channels. This prevents the EGPWS from reporting an external bus fault on the second channel.

CAGE CODE: 97896 SCALE: NONE SIZE: A DWG NO: 060-4314-225 REV: C SHEET 210