Honeywell

MK XXII EGPWS Installation Manual

Table E 3.1.6-246 Non-Integrated EFIS 10 (Bendix/Honeywell)

DISPLAY CONFIGURATION GROUP 246 (BENDIX EFIS 10 DISPLAY, EFS86 RADAR SYSTEM)

Function

Display Type

Sweep Type

Auto Pop Up

Value

Bendix EFIS 10

Normal, Sweep range +/- 90 degrees

Category 7, Options Select Group #1

TA&D Alternate Pop Up: False

TA&D Alternate Pop Up: True

Pop Up On Terrain Caution or

Never Pop Up

Warning.1

 

Peaks Mode

Manual select

Manual deselect

Auto Range

Moving Marker

Overlay Page

Display bus type

TERRAIN DISPLAY BUS #1 453TX_1

A= J1-58

B= J1-59

Category 7, Options Select Group #1

Peaks Enable: False

Peaks Enable: True

Peaks Off

Peaks On

Anytime1

 

Anytime1

No

No

Yes; Without Peaks: “TERR” is located at the bottom left of the display.

With Peaks: Peaks numbers are located at the lower left of the display.

Standard ARINC 708/453

CONNECT TO:

Terrain Display data to switching relay/Symbol Generator #1

TERRAIN DISPLAY BUS #2 453TX_2

A= J1-56

B= J1-57

CONNECT TO:

Terrain Display data to switching relay/Symbol Generator #2

DISPLAY INPUT CONTROL GROUP 246

CHANNEL 429_422RX_1

A= J2-37

B= J2-36

CHANNEL 429RX_3

CONNECT TO: WX-IND 429 out (range) Bus 1 (Low Speed)

Data

Mode (Display Word 1) Range (Display Word 2)

CONNECT TO: WX-IND 429 out (range) Bus 2 (Low Speed)

Fault Designation: DISPLAY BUS 1

Bus Type: Basic

 

 

 

 

 

 

 

Label

Sig. Bits

Range

Signal Type

Resolution

Rate

 

270

Discrete

Mode, Tilt, Gain

Basic

N/A

100 ms

 

271

Discrete

5-320NM

Basic

N/A

100 ms

 

Fault Designation: DISPLAY BUS 2

Bus Type: Basic

A= J2-41

B= J2-40

CONN PIN #

J1-32

J1-31

Data

Mode (Display Word 1) Range (Display Word 2)

REFERENCE NAME

GND_DISC_12

GND_DISC_13

Label

Sig. Bits

Range

270

Discrete

Mode, Tilt, Gain

271

Discrete

5-320NM

PIN FUNCTION

Display Select Discrete #1

Display Select Discrete #2

OUTPUT 429 BUS GROUP 0

Signal Type

Resolution

Rate

Basic

N/A

100 ms

Basic

N/A

100 ms

Polarity/Configuration

Type 1 (Momentary)

Gnd = Display Select Toggle <not> Gnd = Normal

Type 1 (Momentary)

Gnd = Display Select Toggle <not> Gnd = Normal

Channel

Pins

 

Comments

429TX_1 (Low Speed)

A = J2-43

B = J2-42

Transmits (Section 7) Label sets: 7.1.1.x, 7.1.2.x, 7.1.3.x and 7.1.4.x

429TX_2

A = J2-26

B = J2-9

No Connection (No Data Output)

Integration note:

Either weather or a weather test pattern must be displayed before Terrain can be viewed. The white weather annunciation “WX” will still be present when terrain is displayed.

When interfacing to a single display controller configuration the bus must be connected to both EGPWS input channels. This prevents the EGPWS from reporting an external bus fault on the second channel.

CAGE CODE: 97896 SCALE: NONE SIZE: A DWG NO: 060-4314-225

REV: C SHEET 227

Page 227
Image 227
Honeywell MKXXII installation manual Table E 3.1.6-246 Non-Integrated Efis 10 Bendix/Honeywell, Display Input Control Group