Fibre Channel status & statistics | HP E1200-320 instruction

•Select 1 from the Fibre Channel Status menu to display Fibre Channel Link Status. Figure 66 below shows the status and statistics for a Fibre Channel loop. Similar data can also be shown for a Fibre Channel fabric.

Figure 66 Fibre Channel status & statistics

		Fibre Channel Status & Statistics
		X.XX.XX XXXXXX		XXXXXXXXXXXXXXXX
		07/7/2005		08:56:22
Current Fibre	Channel Status - Port 0
LinkState	DOWN	ALPA	x00000000		InDevDataSeqs x00000000
OutDevDataSeq	x00000000	InLnkDataSeqs	x00000000		OutLnkDataSeq x00000000
InP_BSYFrames	x00000000	OutP_BSYFrms	x00000000		InF_BSYFrames	x00000000
InP_RJTFrames	x00000000	OutP_RJTFrame	x00000000		LinkDowns	x00000000
InABTSs	x00000000	OutABTSs	x00000000		LaserFaults	x00000000
SignalLosses	x00000001	SyncLosses	x00000001		BadRxChars	x000000FF
LinkFailures	x00000001	BadCRCFrames	x00000000		ProtocolErrs	x00000000
BadSCSIFrames	x00000000	UnderflowErrs x00000000

A) Autorepeat

C) Clear Statistics

X) Return to previous menu

Command >

Table 7 Fibre Channel status

LinkState is the current FC link status.

AL_PA is the arbitrated loop physical address.

InDevDataSeqs is the number of device data sequences received by this port.

OutDevDataSeq is the number of device data sequences transmitted by this port.

InLnkDataSeqs is the number of link data frames received by this port.

OutLnkDataSeq is the number of link data frames transmitted by this port.

InP_BSYFrames is the number of P_BSY frames received by this port.

OutP_BSYFrms is the number of P_BSY frames transmitted by this port.

InF_BSYFrames is the number of F_BSY frames received by this port.

InP_RJTFrames is the number of P_RJT frames received by this port.

OutP_RJTFrame is the number of P_RJT frames transmitted by this port.

LinkDowns is the number of link down conditions detected.

InABTSs is the number of ABTS frames received.

OutABTSs is the number of ABTS frames transmitted.

LaserFaults is the number of laser faults detected.

SignalLosses is the number of times loss of signal was detected.

e1200-320 4Gb Fibre Channel Interface Card user and service guide 81

Image 81

HP E1200-320 manual Fibre Channel status & statistics

Contents

AD577-96004 Page Contents Visual manager user interface Using the Command Line Interface Troubleshooting Using the FTP interfaceRegulatory compliance and safety Serial and Ethernet pin assignments Addressing, structures, and operations Inband SCSI-3 commandsEnabling Dhcp on the HP e1200-320 4Gb FC Interface Card Glossary Index About this guide Document conventions and symbolsIntended audience Related documentation HP technical support HP-authorized resellerHelpful web sites Shows the layout of the HP e1200-320 4Gb FC Interface Card Introduction Operation indictors Operation indicators Number Description Operation indicators HP e1200-320 4Gb FC Interface Card features How the HP e1200-320 4Gb FC Interface Card worksProcessing Scsi information HP e1200-320 4Gb Interface Card benefits External indicatorsOperating environment Non-operating environment i.e. for unit storage Installation, cabling, and setup Installing the HP e1200-320 4Gb Interface CardIdentifying product components Power supply and AC power cords Removal and installation Removing an interface card from the library Removing an existing interface card Installing the interface card Installing a new card Screws in the black ejector handles 5U cable configuration Page Interfaces and connections Fibre Channel connectionsScsi connection Autobaud feature Ethernet connectionSerial port connection Setting up serial port communications FC port configuration Scsi bus configurationFC switched fabric addressing Device management Host bus adapter configuration DiscoveryLogical unit management Page Device management Serial port management access Configuration methodsOut-of-band Ethernet management access Interface card management Visual manager Command Line Interface FTP Inband SCSI-3 commands Interface card management Visual manager user interface Visual manager access Visual Manager menu structure Main menu Home System menu Serial configuration Network configuration ServerFree Backup Mode not Supported Active fabric configuration User Real-Time Clock configuration Reset menu Ports menu Ports menu Fibre Channel port configuration Scsi Bus 0, 1 configuration screens Scsi bus configuration Discovery menu Perform discovery on Scsi Bus 0 screen Perform discovery on FC Port 0 screen Fibre Channel mapping tasks Mapping menu Viewing and changing Fibre Channel host information Viewing and changing Fibre Channel map information Statistics menu Utilities menu FTP utility screen is used to open an FTP session see Figure FTP utility access FCP/RMI Trace settings configuration Trace Settings Description Event log settingsCurrent, previous, and last assert trace displays Clear current trace buffer or assert trace buffer Event Log screen is used to view the Event Log see Figure Event log display Clear event log Scsi command tracking Report menu Reboot option Power-up messages Using the Command Line Interface Configuration menu Perform configuration Baud rate configuration menu Baud rate configuration Ethernet configuration menu Ethernet configurationPage Fibre Channel configuration menu Fibre Channel configurationPage Using the Command Line Interface This menu allows for setting up Scsi attributes Parallel Scsi configuration Scsi initiator menu This option allows for setting up the Scsi Initiator Maximum Scsi bus speed menu Scsi bus speed configuration menu Device mapping main menu Device mapping Adding an entry Creating an entry for FCP port map Creating an entry Remove gaps Deleting an entryUser selects a LUN ID Following is an example of a host list for FCP hosts Adding a host Editing a host Deleting a host Entire device list Trace and event settings configuration Trace configurationThis option allows set up of trace and events settings Event filter settings Event configuration This option allows selecting the special event log settings Special event logging configuration System clock setup menu Restore last saved configuration Save configurationReset to factory defaults System utilities System status/statistics menu System statistics menu Fibre Channel status Fibre Channel status & statistics Fibre Channel Device Display Parallel Scsi protocol status menu Runtime report Event Log System diagnostics mode Diagnostics mode Special FC Link states menu Special FC link control Get a copy of trace buffer Display trace and assertion history Download a new revision of the firmware Reboot Backup/restore configuration settings Using the FTP interfaceConfiguration backup procedure Configuration restore procedure Put pathfilename.cfg Get a copy of trace buffer or event log Put pathfilename.dlx Updating firmware Using the FTP interface Indicators TroubleshootingGeneral troubleshooting What happens if the Dhcp server cannot be contacted? Login problems Serial port problemsBasic verification Windows driver Verify Scsi bus configuration Verify Fibre Channel connectionVerify Scsi devices in Windows NT Verify host configuration Verify configurationVerify mapping Verify devices Verify HBA device driver information Running diagnosticsTechnical support HP technical support Troubleshooting RJ-11 pin assignments Serial and Ethernet pin assignments DB-9 pin assignments RJ-45 Ethernet Pin Assignments Serial and Ethernet pin assignments Regulatory compliance Regulatory compliance and safetyFederal Communications Commission notice Class a equipment Laser device Laser safety warningModifications Cables Canadian notice avis Canadien International notices and statementsEuropean Union notice Bsmi notice Safety Battery statementJapanese notice Korean notices Taiwan battery recycling notice Regulatory compliance and safety Inband SCSI-3 commands General commandsReport LUNs command All LUNs are reported and will appear in the host’s map Inquiry command Device Identification Evpd Inband SCSI-3 commands SCC addressing structure Addressing, structures, and operationsAddress method definitions SCC logical unit addressing Auto Assigned addressing option SCC addressing option Indexed addressing option Addressing, structures, and operations Enabling Dhcp on the HP e1200-320 4Gb FC Interface Card Setting up Dhcp over interface card interfaces Serial and Telnet interfacesSelect 1. The following menu appears Select 2. The following menu appears XX.XX Xxxxxxxxxxxxxxxx Tips for manipulating Dhcp within Visual Manager Visual Manager Enabling Dhcp on the HP e1200-320 4Gb FC Interface Card Glossary See Fibre Channel Arbitrated Loop Using the standard Fibre Channel frame and sequence formatsFC adapter FC link. This is also known as an HBA, or Host Bus Adapter Known as a target usually a peripheral Low Voltage Differential/Single-EndedFrame Reset Scsi Point-to-Point configurationsProcessor Card Scsi device Errors may occurTransmission Control Protocol Block/termination 128 Index 130 Dhcp 132