Two Identical Drivers | HP UX 11i v1 Networking Software guide

Installing or Upgrading NetWare Client Software

Using Two Network Boards

link driver ntr2000

int 5

port a20

mem cc000

frame token-ring

frame token-ring_snap

Two Identical Drivers

If you have two network boards using the same type of ODI LAN driver, do not load the same driver twice in the NET.CFG ﬁle and do not specify a “Protocol Stack” option.

Instead, use the Link Driver option in NET.CFG to specify that the same driver is used twice.

Do this by placing two Link Driver sections in the NET.CFG ﬁle, each one specifying the driver name and hardware settings used by that network board.

The hardware settings for at least one of the network boards must be modiﬁed, because you cannot have two network boards of the same type with both using default hardware settings.

For example, if you have two NE2000 LAN drivers, you might include the following lines in the NET.CFG ﬁle:

link driver ne2000 int 5

port 360

frame ethernet_802.2 frame ethernet_802.3

link driver ne2000 int 4

port 320

frame ethernet_802.2 frame ethernet_802.3

Putting two occurrences of “link driver ne2000” loads the NE200 driver twice.

5-32

Image 154

HP UX 11i v1 Networking Software manual Two Identical Drivers

Contents

HP Part No. J2771-90015 HP 9000 NetworkingEdition Restricted Rights Legend Hewlett-Packard Co Homestead Road Cupertino, CA 95014 USA Printing History Preface Installation, Login, and Setup OverviewIntroduction Contents Integration with Other Systems Overview Management Services Overview Client-server solutions for your client workstationsThis section contains one chapter Appendixes Overview This section includes the chapter shown belowThis section is divided into two chapters as shown below Documentation Conventions This manual uses the following Novell conventions Asterisk Login SERVER1/SUPERVISOR /option Netbios TNVT220 Supplemental Documentation Xiii Preface Xiv Contents Introduction NetWare DOS Requester Architecture Where to Go from Here Additional InformationUnderstanding the NetWare Client Software Overview NetWare Protocols and Transports Using NetWare User Tools for MS Windows Using NetWare User Tools for DOS NetuserUnderstanding Client Tools Editing the INSTALL.CFG File Preparing the NetWare Client Installation SoftwareSetting Up for Installation from a Network Directory Introduction Preparing Client Workstations What Happens during Installation Installing or Upgrading NetWare Client Software OverviewInstalling for MS Windows for Workgroups Understanding Logging In to NetWare Directory Services Setting Up NetWare Client Workstations to Log In OverviewModifying the NET.CFG File for Logging In to NetWare Logging In from a NetWare Client Workstation Overview Setting Up and Managing Network DrivesOverview Introduction Setting Up Client Workstation Printing Overview Introduction Installing Source Routing on the Server 10-8 11-16 Using the Wsupdate Utility Overview A-2 Introduction A-3Using the Wsupgrd Utility Overview B-2 Additional Information 11-17 Additional Information B-12 Xxvi Understanding Networking Basics Overview Topic Introduction Client-Server Networks Network TypesPeer-to-Peer Networks Simple Client-Server Network Physical Connection Network ConnectionsNetwork Board and Cabling Logical Connection Resources for NetWare 2 and NetWare Network ResourcesResources for NetWare Components of a Directory Tree Example of a Directory Tree Structure of the File System File Structure for NetWare 2 and NetWare File Structure for NetWare NetWare 2 and 3 File System Structure and Directory Path TSERVERSYS.Test.MedTec Products \ Domestics \ Sales.rpt NetWare 4 File System Structure and Directory Path NetWare 2 and NetWare 3 Users Network UsersNetWare 4 Users Network Users Login Login Attributes can also be used to Network SecurityNetwork Security Levels File System Security Additional Network Security in NetWare Login and Password SecurityServer Security Network Security Network Printing Network PrintingNon-Networked Printing Standalone Printing Network Printing Where to Go from Here If you want to See For NetWare Additional InformationFor NetWare 2.2, NetWare 3.11, and NetWare Topic Reference NetWare 4 Print Services Understanding the NetWare Client Software Following topics are covered in this chapter Core Components of the NetWare Client for DOS and MS Windows TSR Program Description Introduction Three-Layer Structure NetWare DOS Requester Architecture.VLM ﬁles are grouped into the following three layers NetWare DOS Requester Layers and Modules Service Protocol LayerDOS Redirection Layer Protocol Layer Service Description Module Key Components of the NetWare DOS Requester VLM Manager Communication and Connection ManagementTransport Protocol Layer Connection Table Manager NetWare DOS Requester offers several improvements over Netx Backwards Compatibility with Netx ApplicationsComparison of Netx and NetWare DOS Requester Architecture File and Print Services Memory Usage NetWare Protocols and Transports Ipxodi Protocol SPX Protocol TCP/IP Protocol Fddi ODI LAN Driver NET.CFG File Novell MS Windows Support Accessing the Network from an MS Windows ApplicationSupport File Description Running DOS Applications in Enhanced Mode Accessing the Network from an MS Windows Application Running a DOS Application in Enhanced Mode Receiving Broadcast Messages Printing to Network Queues Receiving a Broadcast Message GDI Printing to a Network Queue Where to Go from Here For NetWare 2 and NetWare Understanding Client Tools Understanding Client Tools Introduction Prerequisites Starting NetWare User Tools for DOS Netuser ProcedurePrerequisites For example, if you mapped network drive G to PUBLIC, type Using NetWare User Tools for DOS Netuser Options Using NetWare User Tools for DOS NetuserAccessing Online Help Use Printing to Use Attachments to Use Messages toUse Drives to Use Change Context to To exit NETUSER, choose Yes when prompted Exiting NetWare User Tools for DOS Netuser Starting NetWare User Tools for MS Windows Using Quick Keys Using NetWare User Tools for MS WindowsQuick Keys Tool Using the Menu Bar Menu Bar for NetWare User Tools for MS Windows NetWare Drive Connections Using NetWare User Tools for MS Windows OptionsNetWare Drive Connections Window Viewing the Resources List Using the NetWare Drive Connections WindowWhen using this window, remember NetWare Printer Connections Using the NetWare Printer Connections Window NetWare Printer Connections Window Setting LPT Options LPT Setting Options Explanation NetWare Connections Using the NetWare Connections WindowNetWare Connections Window Setting a New Password NetWare Send Message NetWare Send Message Window Using the NetWare Settings Window Using the NetWare Send Message WindowNetWare Settings Use this window to Using NetWare SettingsNetWare Settings Options Option Explanation Using NetWare User Tools for MS Windows Manager applications Setting the User-Deﬁned ButtonsProcedure User-Defined Buttons 1 Changing the User-Deﬁned Path Accessing and Changing Directory and File AttributesFile and Directory Properties Window File and Directory Property Attributes Using the File and Directories Property windowOptimizing the NetWare Client Software for MS Windows Attribute Explanation Optimizing the NetWare Client Software for MS Windows Condition Explanation Exiting NetWare User Tools for MS Windows Printing in NetWare 3.12 Concepts Printing in NetWare 4 Concepts Additional Information Preparing to Install or Upgrade the NetWare Client Software Preparing to Install or Upgrade the NetWare Client Software Introduction Setting Up Workstation Hardware Preparing Client Workstations Setting Up the Network Board Following settings If you have Then Device LPT1 Port Device Setting Up Workstation Software Preparing Client Workstations Preparing the NetWare Client Installation Software Setting Up for Installation from a Network Directory Mapping a Network Drive for Installation Procedure Volume and directory are SYSPUBLIC\CLIENT\DOSWIN for DOSVolume and directory MS Windows Modifying the Requester section in the INSTALL.CFG File Editing the INSTALL.CFG FileSuggested Modifications to the Requester Section Upgrade of the NetWare DOS Requester Change in First Network Drive Short machine type=ibm NetWare Client installation software Using a Third-Party ODI LAN DriverTo obtain a driver compatible with NetWare Upgrading Your IPX Driver to ODI Where to Go from Here Where to Go from Here Installing or Upgrading NetWare Client Software Installing or Upgrading NetWare Client Software Introduction Running the NetWare Client Installation Program Loading the Installation Program Updating System Files on Your Workstation Following procedure. Otherwise, accept the default path Automatically assigns the default path C\NWCLIENTThese steps Updating System Files on Your Workstation Changes Made to Your AUTOEXEC.BAT File Installing Support for MS Windows Changes Made to Your CONFIG.SYS File Procedure Customize Support for MS Windows Screen Running the NetWare Client Installation Program Installing LAN Drivers Prerequisite Network Board Type Procedure Read-Only Files Copying FilesExisting Files Swapping Diskettes Running the NetWare Client Installation Program Directory Is Created What Happens during InstallationFiles Are Copied DOS and NetWare Configuration Files Are Created or Modified CONFIG.SYS and AUTOEXEC.BAT MS Windows Configuration Files Are Modified Boot Network Boot.description386Enh Windows Icon in NetWare Tools Group Is CreatedGroups Installing for MS Windows for Workgroups Installing for MS Windows for Workgroups Installing for MS Windows for Workgroups Setting Up Network Directories and Files Prerequisites @echo OFF If %NETDRV%==NETX goto Netx nul Create another ﬁle called SYSTEM.NTX Loading the NetWare Client Software Reasons for Having Two Network Boards Using Two Network BoardsDifferent Communication Software Package Modifying Client Workstation Files for Two Network Boards Physically Separated Networks Two Different Drivers Two Identical Drivers Link driver ne3200 Slot Frame ethernet802.2 Using Two Network Boards Reference, in NetWare Client for DOS Where to Go from Here Setting Up NetWare Client Workstations to Log Setting Up NetWare Client Workstations to Log Introduction Adding the Preferred Server Parameter to the NET.CFG File Using the Preferred Server ParameterExample of the NetWare DOS Requester Section Using the Name Context Parameter Modifying the NET.CFG File for Logging In to NetWare Using the Preferred Tree Parameter Modifying the NetWare DOS Requester Option Example of the NetWare DOS Requester Section Understanding Logging In to NetWare Directory Services Specifying the Name Type of an Object Changing Your Context Logging In to Your Context Additional Information Additional Information Logging In from a NetWare Client Workstation Logging In from a NetWare Client Workstation Introduction Ensure the following before logging IPXODI.COM VLM.EXE Logging In from the DOS Prompt Logging In to a NetWare 2 or NetWare 3 Network Logging In to a NetWare 4 Network Logging In to NetWare 4 with a NetWare Bindery Connection Login TSMKT/ESAYERS /B Enter Logging In from MS Windows Logging Out from MS Windows Logging Out of a NetWare Server or NetworkLogging Out from DOS Log out in one of the following ways Logging Out of a NetWare Server or Network DOS and MS Windows Technical Where to Go from Here Setting Up and Managing Network Drives Setting Up and Managing Network Drives Introduction Introduction Using NetWare Utilities to Set Up and Manage Drive Mappings Prerequisites Version Reference MAP UtilityAssigning Drive Mappings in a Specific Order Assigning Drive Mappings for Diverse Environments Assigning Search Drives Assigning Drives to Directory Map Objects NetWare 4 only Instead, you would type NetWare User Tools for DOS the Netuser Utility NetWare User Tools for MS Windows the NWUSER.EXE Program Using the NetWare Drive Connections Window Remember the following Viewing the Resources List Resources list contains the followingMaking Drive Mappings Permanent Using Universal Naming Convention UNC Paths in MS Windows Program Group .GRP Files Program Items Files Program Information Files PIFs Referencing Files Referencing a File in the Open or Save As Text Box Concepts Setting Up Client Workstation Printing Setting Up Client Workstation Printing Introduction Using NetWare Utilities to Set Up Network Printing Use Capture to Using Capture at the Command LineCapture Utility Example Using Capture Login Scripts or Profiles This command indicates the followingSetting the Number of Available Printer Connections Add the following lines to the file NetWare User Tools for MS Windows the NWUSER.EXE Program Printers Dialog Connect Dialog NetWare Printer Connections Window Using a Local Printer on the Network Network Options Dialog Port Lp1= Lp2= Lp3= Lp4= Net1= Record.prn= Ports Redirection might not function for all applications Option, in NetWare Client for DOS Setting Up Source Routing Support for a Token-Ring Network 10-2 10-3 Network Configuration Using Source Routing Bridges 10-5 Installing Source Routing on the Server MAC 10-7 Copying the Files to the NetWare Client Directory Manually Diskette Name Directory Filename 10-9 Modifying the CONFIG.SYS File Modifying the STARTNET.BAT File Procedure 10-11 Loading the Source Routing Driver Unloading the Source Routing Driver 10-14 Configuring Client Workstations for Desktop Snmp Services 11-2 11-3 Installing an Snmp Management System Console Installing the Desktop Snmp Software File Description Copying the Necessary Files to the NetWare Client Directory WSDRVPRN.VLM Manually Modifying DOS System and NetWare Client Configuration Files Modifying the STARTNET.BAT File 11-9 Modifying the NET.CFG File Sample NET.CFG File for Desktop Snmp Services Configuring the HRMIB.INI File Sample Configuration File HRMIB.INI for the HRMIB.EXE File 11-13 Loading the Desktop Snmp Software Unloading the Desktop Snmp Software Configuring Client Workstations for Better Performance 11-17 Additional Information 11-18 Using the Wsupdate Utility Using the Wsupdate Utility Introduction Updating Files from a Login Script or Profile Using Wsupdate to Update Files on Client WorkstationsUpdating Files from the Command Line Before you load WSUPDATE, ensure that Using Syscon Using NetWare Administrator Using Wsupdate to Update Files on Client Workstations Using Netadmin Using Wsupdate to Update Files on Client Workstations Syscon in Utilities Reference Using the Wsupgrd Utility Using the Wsupgrd Utility Introduction Typical upgrade requires the following ﬁles in Syspublic WSUPGRD.EXE LSL.COM IPXODI.COM Using the Wsupgrd /I Option Upgrading IPX LAN Drivers from a Login Script or Profile Using Wsupgrde to Upgrade Network Board DriversUpgrading IPX LAN Drivers from the Command Line Before you load WSUPGRD, ensure that Enter a password if required At the command line, type Wsupgrd NE2000 /N Wsupgrd odidriver option Networkboarddriver.COM Using Wsupgrde to Upgrade Network Board Drivers Wsupgrd in Utilities Reference Accessing Index CONFIG.SYS Hardware Mappings Logging in from WSUPDATE, A-4 Viewing NetWare Administrator, B-8 in SYSCON, B-7 Index