Manuals / Brands / Computer Equipment / Network Router / Huawei / Computer Equipment / Network Router

Huawei Aolynk DR811, Aolynk DR814 5.2 Configuring a PC Connected by USB Port

1 77

Download 77 pages, 1.48 Mb

User Manual

Aolynk DR811/DR814 ADSL2+Broadband Router 5 Configuring Your Computers

53

5.2 Configuring a PC Connected by USB Port

5.2.1 Connecting a Computer to the USB Port by a USB cable

If you use the ADSL router’s USB port to connect to a PC, you must install the provided

USB driver on the PC. The driver enables Ethernet-over-USB communication with the

ADSL router.

5.2.2 Installing the USB Driver

Ensure that the USB function of your PC is OK.

The Microsoft Windows 98, 98 SE, ME, 2000, and XP support this driver. The following

installation instruction is based on Windows XP; you may refer to it when operating on

other operating systems.

1. Insert the driver CD to your CDROM.

The CD shipped with the ADSL router contains the USB drivers. Insert it into your PC’s

CDROM.

2. Plug the USB cable from the device into the USB port of the PC.

The USB cable provided has a flat connector on one end (called Type A) and a square

connector on the other (Type B). Connect the flat connector to your PC and the square

connector to the ADSL router.

To ADSL-

Ethernet router

To PC

Figure 5-1 USB port outline

Plug the USB cable from the device into the USB port of the PC. The PC will detect the

newly-attached device and display the Found New Hardware Wizard dialog box:

Contents

Main HUAWEI Page Page Table of Contents Page 1 Introductions 1.1 Product Overview 1.2 Appearance 1.2.1 Front View 1.2.2 Rear View 1.3 Features 1.4 Parts Check 2 Connecting Your Device 2.1 Overview 2.2 Steps 2.3 Finish 3 Getting Started with the Web Pages 3.1 Accessing the Web Pages 1. The default IP settings for the ADSL router are as follows: Page 5. Click OK. The Welcome page is displayed: 3.2 Web Page Layout 3.3 Commonly Used Buttons 3.4 Testing Your Setup 3.5 Default Device Settings 4 Web-based Management 4.1 Quick Setup 4.2 WAN Setting Page 4.3 DNS Relay 4.4 LAN Setting Page 4.5 DHCP 4.6 Route Page Page 4.7 Security Interface Page Page 4.8 DMZ Configuration Page 4.9 Security Policy 4.10 Trigger Page Page 4.11 IDS 4.12 SNTP 4.13 ZIPB Page 4.14 Password 4.15 Remote Access 4.16 Restart Router 4.17 Configuration Backup/Restore Page 4.18 Upgrade 4.19 Status Page 4.20 Log 4.21 PVC Scan 4.22 Save Configure 5 Configuring Your Computers 5.1 Configuring Ethernet PCs 5.1.1 Before You Begin 5.1.2 Windows XP PCs 5.1.3 Windows 2000 PCs 5.1.4 Windows Me PCs 5.1.5 Windows 95, 98 PCs 5.1.6 Windows NT 4.0 Workstations 5.1.7 Assigning Static Internet Information to Your PCs 5.2 Configuring a PC Connected by USB Port 5.2.1 Connecting a Computer to the USB Port by a USB cable 5.2.2 Installing the USB Driver 1. Insert the driver CD to your CDROM. 2. Plug the USB cable from the device into the USB port of the PC. Page Page 5.2.3 Configuring IP Properties on PC Connected by USB Port 6 IP Addresses, Network Masks, and Subnets 6.1 IP Addresses 6.1.1 Structure of an IP Address 6.1.2 Network Classes 6.2 Subnet Masks Page 7 Service Configuration 7.1 Configuration Overview 7.2 PureBridge 7.3 DHCP/StaticIP 7.4 IPoA 7.5 PPPoA 7.6 PPPoE Page 8 Troubleshooting 8.1 Troubleshooting Suggestions Page 8.2 Diagnosing Problem Using IP Utilities 8.2.1 ping 8.2.2 nslookup 9 Appendix - Glossary