Manuals / IBM / Computer Equipment / Network Card

IBM manual MaxLoader User’s Guide, Introduction, Getting Started / Installation

Models: MaxLoader

1 118

Page 1

	MaxLoader User’s Guide
1. INTRODUCTION	7
PROGRAMMER MODELS FOR PC USB INTERFACE	7
PROGRAMMER MODELS FOR PC USB INTERFACE MULTI-SOCKETS	8
PROGRAMMER MODELS FOR PC PARALLEL INTERFACE	8
ABOUT THIS MANUAL	9
GENERAL DESCRIPTION	9
2. GETTING STARTED / INSTALLATION	10
INSTALLATION REQUIREMENTS	10
HARDWARE INSTALLATION	10
To Install the software from a CD drive	10
TO START THE WINDOWS SOFTWARE	10
TO INSTALL SOFTWARE AND CONNECT TO PC FOR USB PROGRAMMERS	10
TO INSTALL THE SOFTWARE FOR PARALLEL PORT PROGRAMMERS	17
To download the software from the www.eetools.com web site	17
SELECT PRODUCT	18
3. FAMILIES OF PROGRAMMABLE DEVICES	19
NVM: NON VOLATILE MEMORY	19
ROM: READ ONLY MEMORY	19
OTP: ONE TIME PROGRAMMABLE ROM	19
EPROM: ERASABLE PROGRAMMABLE ROM	19
EEPROM: ELECTRICALLY ERASABLE & PROGRAMMABLE ROM	19
NVM HIERARCHY	19
SERIAL FLASH EEPROM	21
SERIAL EEPROM	21
NON-TYPICALDEVICES	22
8-BIT1-MEGABITS	22
16-bit1-Megabits	23
ERASING AN EPROM	23
PLD	23
	1

Page 1

Image 1

IBM manual MaxLoader User’s Guide, Introduction, Getting Started / Installation, Families Of Programmable Devices

Contents

2. GETTING STARTED / INSTALLATION MaxLoader User’s GuideTo Install the software from a CD drive 1. INTRODUCTION4. TERMS AND SYMBOLS USED IN THE GUIDE PLD FeaturesSAFETY NOTE CONVENTIONS MICROCONTROLLERBuffer MaxLoader User’s GuideDevice Config Test This feature is for only TopMax, TopMaxIIHow to program write buffer blocks data into different sockets ? How to program write one file into different sockets ?7. TROUBLE SHOOTING & TECHNICAL SUPPORT 9. ABOUT NAND FLASH MEMORY 8. OTHER PRODUCTS10. GLOSSARY MaxLoader User’s GuideProgrammer Models for PC USB Interface 1. INTRODUCTIONEE Tools, Inc Programmer Models for PC parallel Interface Programmer Models for PC USB Interface Multi-SocketsMaxLoader User’s Guide General Description About This ManualHardware Installation To install software and connect to PC for USB programmersTo Install the software from a CD drive 2. GETTING STARTED / INSTALLATION Installation Requirementsƒ Follow the steps below for Windows MaxLoader User’s Guide ƒ Follow the steps below for installation for USB 2.0 driver 5. Set up MaxLoader softwareMaxLoader User’s Guide MaxLoader User’s Guide MaxLoader User’s Guide 9. Execute MaxLoader and choose Programmer model MaxLoader User’s Guide10. Choose your programmer that is ready to be use in your computer To install the Software for parallel port programmers Select Product NVM Hierarchy 3. FAMILIES OF PROGRAMMABLE DEVICESƒ NVM Non Volatile Memory ƒ ROM Read Only Memory ƒ OTP One Time Programmable ROM ƒ EPROM Erasable Programmable ROMMaxLoader User’s Guide Flash Memory Flash Memory TechnologiesSerial Flash EEPROM Performance ComparisonSerial EEPROM ƒ Xilinx 17xx familyNon-Typical Devices 8-bit 1-Megabits Erasing an EPROM 16-bit 1-MegabitsPLD Features Microcontroller About “Device ID” and “Auto Select” on EE Tools programmers Protection and Watchdog timer, and etc. To program this fuse1. Program the EPROM portion of the device 2. Click on Option 3. Make any changes if necessaryTo Find a Device ID Safety Note Conventions 4. TERMS AND SYMBOLS USED IN THE GUIDEOther terms and definitions are as follows Choosing a Right Adapter MaxLoader User’s Guide Different Device PackagesPLCC TSOPMaxLoader User’s Guide Different Programming AdaptersPLCC-TO-DIP TSOP-TO-DIPProgramming an EPROM with data 5. QUICK START EXAMPLESMaxLoader User’s Guide Source Device Programmed AMD 27C256 Duplicating an EPROM from a master IC deviceBasic Menu Screen Information Option Information 6. MAXLOADER OPERATIONSTarget Device Erased or blank INTEL 27C256 SplitAdditional Option Information for Non PLD Devices PinsSystem Information CounterFile Verification errorStart Start address of memory that contains serialized data End End address of memoryƒ Intel HEX Format ƒ Binary Format02 0000 02 4A29 Check Sum Index address Record type Address ƒ Motorola S HEX FormatRecord Length ƒ ASCII HEX format ƒ TEKTRONIX HEX FORMAT00001102444154414D414E2053332053455249414C8F 01000001 Global Engineering Documents Inc. at 800 ƒ JEDEC Standard PLD devices onlyElectronic Industries Association at 202 Sum Check File / Load ƒ POF file Altera EPMxxx devices onlyFile / Reload File/ Save Project File/ Load ProjectFile / Save MaxLoader User’s Guide File/ Save LogThe .txt file can be saved in any folder, and opened in “Note Pad.” MaxLoader User’s Guide File/ Save All MessagesMaxLoader User’s Guide BufferFind Buffer / Edit BufferThe data looking for ASCII value The data looking for HEX valueFill Buffer Find NextFill random data Fill Buffer Copy bufferMaxLoader User’s Guide Enter certain data between 2 different buffer locationsMaxLoader User’s Guide Clear bufferPrint buffer Set editor to view modeThis mode allows you not to modify data in the buffer MaxLoader User’s GuideSet Editor to binary mode Set editor to edit modeData in buffer can be modified in this mode The data in current buffer will be changed as binary modeSet editor to 16 bitword Hex Set editor to 8 bitbyte HexMaxLoader User’s Guide The data in current buffer will be changed as 8-bit hex valueSet editor to 32 bitdouble word Hex Set default editor modeThe data in current buffer will be changed as 32-bit mode MaxLoader User’s GuideSwap nibble Set default Reset EditorThe cursor mode will be the first data in address MaxLoader User’s GuideSwap Word Swap byteMaxLoader User’s Guide Swap each 8-bit 1-byte data in each 16-bit4-byte blockJedec editor Swap double wordClear Close DeviceBuffer / Edit UES Device / Select by history Select ƒ Select / PLD ƒ Select / E EPROM, FLASHƒ Select / Microcontroller ƒ Select / PROMMaxLoader User’s Guide Select / Device informationDevice / Change Algorithm Device / Blank Check Device / Auto Menu OptionCHECK routine after they are secured even though they are not blank CAUTION Some devices such as Philips P98C52 can pass the BLANKƒ Memory device Device / Programƒ Programmable Logic Device operation ƒ 28C256, 28C010, etcCopy from a master chip to a new chip ƒ Microchip PIC devicesƒ Serial EEPROMs ƒ MOTOROLA MC68HC908 devicesƒ Atmel or Xilinx Device / Verify Device / ReadDevice / Erase Device / Data CompareDevice / Security Device / Option Device / EncryptionTest / RAM Test Device / AutoDRAM types tested SRAM type testedTest / Vector Test Test / IC Test DelayOptional Operation X valueConfig / Select Product ConfigTest Config Option / Buffer Clear Before File Loading Config / Config OptionConfig Option / Verify After Reading Config Option / Blank Check Before ProgrammingConfig Option / verify after programming Config Option / Byte order swappingMaxLoader User’s Guide byte swap = disabledConfig Option / Device ID Check Config Option / Device Insert TestMaxLoader User’s Guide Config Option / Default Buffer Value Config Option / SoundConfig Option / 32 Bit Checksum MaxLoader User’s Guide Config Option / Port TopMax, ChipMaxA parallel port address can be determined by the MaxLoader TopMax ChipMax softwareUSB option / Enable START button Config Option / USB Option USB programmerEnabling #4 socket to be master socket USB option / Enable “START ALL” buttonUSB option / Good LED off on socket open Enabling any button to be a “Start Key” Config Option / Gang Split SelectMaxLoader User’s Guide NOTE Do not run this operation in “Concurrent Mode” SplitByte $0001 Byte $0003Config Option / Address These addresses will be applied for programming the buffer data Device AddressNOTE Device size for different devices File LoadFile Save Config Option / Auto IncConfig / Hardware test Config / Concurrent gang modecontrol. You can execute individual socket with corresponding start button or all sockets together with pressing any of START button Enabling any button to be a “Start Key” The individual socket with a serial number can be executed once the Start button is pressed. After check the Enables START ALL button box in Config option, all 8 sockets will be executed when you click on any of the “START” key in Gang program. The START ALL button make all socket If the box is not checked, individual socket will be executed once the button that contains a serial number actual programming socket is clickedClose MaxLoader User’s Guide How to program write one file into different sockets ?EPROM EXAMPLE 1 PROGRAM 8 OF 27128 EPROMS WITH SAME DATA Click for operating all sockets at once, concurrent mode Click for individual socket operationMaxLoader User’s Guide This option is not available for all other devices that are not 8-bit EPROMs. The menu screen below illustrates that there is no Set Program button because the device selected DA28F320J5 is not 8-bit EPROM How to program write buffer blocks data into different sockets ?MaxLoader User’s Guide NOTE Who may need the “set Programming?”MaxLoader User’s Guide Config / Enter Supervisor Mode Config / Enter Production ModeConfig / Language Config / Set Password2. Software Updates 7. TROUBLE SHOOTING & TECHNICAL SUPPORT3. Testing the Hardware 1. Registration4. Quick Self-Diagnostics 5. Contacting Customer Support Electronic Engineering Tools, Inc 6. Service Information4620 Fortran Drive, Suite 102 San Jose, CA 95134, USA. Tel Fax 7. Limited One-Year Warranty MaxLoader User’s Guide 8. Useful Web Site Addresses/ Phone Numbers10. EPROM Emulator Manufacturers 9. Programming Adapter Manufacturers8. OTHER PRODUCTS Optional EPROM EmulatorComparison of NOR and NAND Flash technologies 9. ABOUT NAND FLASH MEMORYMaxLoader User’s Guide How to Program NAND Flash Why NAND FlashMaxLoader User’s Guide 10. GLOSSARY How to READ NAND FlashBipolar PROM Blank CheckFunctional Test FPGAFuse Gang ProgrammerJEDEC HEX fileJEDEC file Memory deviceNon-Volatile MicrocontrollerOscillator PackageSerial Memory PQFPSocket module SOICUV Erasable TSOPVerify Word width

MaxLoader User’s Guide

1. INTRODUCTION

2. GETTING STARTED / INSTALLATION

To Install the software from a CD drive

3. FAMILIES OF PROGRAMMABLE DEVICES

16-bit1-Megabits