Manuals / IBM / Computer Equipment / Network Card

IBM MaxLoader manual Introduction, Programmer Models for PC USB Interface, EE Tools, Inc

Models: MaxLoader

1 118

Download 118 pages 6.46 Kb

Page 7

Image 7

MaxLoader User’s Guide

1. INTRODUCTION

This manual describes the operation of EE Tools’ programmers. TopMax/ChipMax/ChipMax2/TopMaxII/UniMax/ProMax8G (4G) are software, MaxLoader, driven device programmers. The information contained in this manual has been reviewed for accuracy, clarity, and completeness.

Please report in writing any errors or suggestions to support@eetools.com

EE Tools, Inc.

4620 Fortran Drive Suite 102

San Jose, CA 95134, USA. www.eetools.com

Tel : (408)263-2221 Fax : (408)263-2230

EETools reserves the right to use and distribute any information supplied without obligation.

Programmer Models for PC USB Interface

Page 7

Image 7

IBM MaxLoader manual Introduction, Programmer Models for PC USB Interface, EE Tools, Inc

Contents

1. INTRODUCTION MaxLoader User’s Guide2. GETTING STARTED / INSTALLATION To Install the software from a CD driveMICROCONTROLLER PLD Features4. TERMS AND SYMBOLS USED IN THE GUIDE SAFETY NOTE CONVENTIONSBuffer MaxLoader User’s GuideDevice Config Test This feature is for only TopMax, TopMaxIIHow to program write buffer blocks data into different sockets ? How to program write one file into different sockets ?7. TROUBLE SHOOTING & TECHNICAL SUPPORT MaxLoader User’s Guide 8. OTHER PRODUCTS9. ABOUT NAND FLASH MEMORY 10. GLOSSARYProgrammer Models for PC USB Interface 1. INTRODUCTIONEE Tools, Inc Programmer Models for PC parallel Interface Programmer Models for PC USB Interface Multi-SocketsMaxLoader User’s Guide General Description About This Manual2. GETTING STARTED / INSTALLATION Installation Requirements To install software and connect to PC for USB programmersHardware Installation To Install the software from a CD driveƒ Follow the steps below for Windows MaxLoader User’s Guide ƒ Follow the steps below for installation for USB 2.0 driver 5. Set up MaxLoader softwareMaxLoader User’s Guide MaxLoader User’s Guide MaxLoader User’s Guide 9. Execute MaxLoader and choose Programmer model MaxLoader User’s Guide10. Choose your programmer that is ready to be use in your computer To install the Software for parallel port programmers Select Product ƒ OTP One Time Programmable ROM ƒ EPROM Erasable Programmable ROM 3. FAMILIES OF PROGRAMMABLE DEVICESNVM Hierarchy ƒ NVM Non Volatile Memory ƒ ROM Read Only MemoryMaxLoader User’s Guide Flash Memory Flash Memory Technologiesƒ Xilinx 17xx family Performance ComparisonSerial Flash EEPROM Serial EEPROMNon-Typical Devices 8-bit 1-Megabits Erasing an EPROM 16-bit 1-MegabitsPLD Features Microcontroller 3. Make any changes if necessary Protection and Watchdog timer, and etc. To program this fuseAbout “Device ID” and “Auto Select” on EE Tools programmers 1. Program the EPROM portion of the device 2. Click on OptionTo Find a Device ID Safety Note Conventions 4. TERMS AND SYMBOLS USED IN THE GUIDEOther terms and definitions are as follows Choosing a Right Adapter TSOP Different Device PackagesMaxLoader User’s Guide PLCCTSOP-TO-DIP Different Programming AdaptersMaxLoader User’s Guide PLCC-TO-DIPProgramming an EPROM with data 5. QUICK START EXAMPLESMaxLoader User’s Guide Source Device Programmed AMD 27C256 Duplicating an EPROM from a master IC deviceSplit 6. MAXLOADER OPERATIONSBasic Menu Screen Information Option Information Target Device Erased or blank INTEL 27C256Counter PinsAdditional Option Information for Non PLD Devices System InformationEnd End address of memory Verification errorFile Start Start address of memory that contains serialized dataƒ Intel HEX Format ƒ Binary Format02 0000 02 4A29 Check Sum Index address Record type Address ƒ Motorola S HEX FormatRecord Length ƒ ASCII HEX format ƒ TEKTRONIX HEX FORMAT00001102444154414D414E2053332053455249414C8F 01000001 Global Engineering Documents Inc. at 800 ƒ JEDEC Standard PLD devices onlyElectronic Industries Association at 202 Sum Check File / Load ƒ POF file Altera EPMxxx devices onlyFile / Reload File/ Save Project File/ Load ProjectFile / Save MaxLoader User’s Guide File/ Save LogThe .txt file can be saved in any folder, and opened in “Note Pad.” MaxLoader User’s Guide File/ Save All MessagesMaxLoader User’s Guide BufferThe data looking for HEX value Buffer / Edit BufferFind The data looking for ASCII valueFill Buffer Find NextFill random data Enter certain data between 2 different buffer locations Copy bufferFill Buffer MaxLoader User’s GuideMaxLoader User’s Guide Clear bufferMaxLoader User’s Guide Set editor to view modePrint buffer This mode allows you not to modify data in the bufferThe data in current buffer will be changed as binary mode Set editor to edit modeSet Editor to binary mode Data in buffer can be modified in this modeThe data in current buffer will be changed as 8-bit hex value Set editor to 8 bitbyte HexSet editor to 16 bitword Hex MaxLoader User’s GuideMaxLoader User’s Guide Set default editor modeSet editor to 32 bitdouble word Hex The data in current buffer will be changed as 32-bit modeMaxLoader User’s Guide Set default Reset EditorSwap nibble The cursor mode will be the first data in addressSwap each 8-bit 1-byte data in each 16-bit4-byte block Swap byteSwap Word MaxLoader User’s GuideJedec editor Swap double wordClear Close DeviceBuffer / Edit UES Device / Select by history Select ƒ Select / PROM ƒ Select / E EPROM, FLASHƒ Select / PLD ƒ Select / MicrocontrollerMaxLoader User’s Guide Select / Device informationDevice / Change Algorithm Device / Blank Check Device / Auto Menu OptionCHECK routine after they are secured even though they are not blank CAUTION Some devices such as Philips P98C52 can pass the BLANKƒ 28C256, 28C010, etc Device / Programƒ Memory device ƒ Programmable Logic Device operationCopy from a master chip to a new chip ƒ Microchip PIC devicesƒ Serial EEPROMs ƒ MOTOROLA MC68HC908 devicesƒ Atmel or Xilinx Device / Verify Device / ReadDevice / Erase Device / Data CompareDevice / Security Device / Option Device / EncryptionSRAM type tested Device / AutoTest / RAM Test DRAM types testedTest / Vector Test X value DelayTest / IC Test Optional OperationConfig / Select Product ConfigTest Config Option / Buffer Clear Before File Loading Config / Config OptionConfig Option / Byte order swapping Config Option / Blank Check Before ProgrammingConfig Option / Verify After Reading Config Option / verify after programmingMaxLoader User’s Guide byte swap = disabledConfig Option / Device ID Check Config Option / Device Insert TestMaxLoader User’s Guide Config Option / Default Buffer Value Config Option / SoundConfig Option / 32 Bit Checksum ChipMax software Config Option / Port TopMax, ChipMaxMaxLoader User’s Guide A parallel port address can be determined by the MaxLoader TopMaxUSB option / Enable START button Config Option / USB Option USB programmerEnabling #4 socket to be master socket USB option / Enable “START ALL” buttonUSB option / Good LED off on socket open Enabling any button to be a “Start Key” Config Option / Gang Split SelectMaxLoader User’s Guide Byte $0003 SplitNOTE Do not run this operation in “Concurrent Mode” Byte $0001Config Option / Address File Load Device AddressThese addresses will be applied for programming the buffer data NOTE Device size for different devicesFile Save Config Option / Auto IncConfig / Hardware test Config / Concurrent gang modecontrol. You can execute individual socket with corresponding start button or all sockets together with pressing any of START button Enabling any button to be a “Start Key” The individual socket with a serial number can be executed once the Start button is pressed. After check the Enables START ALL button box in Config option, all 8 sockets will be executed when you click on any of the “START” key in Gang program. The START ALL button make all socket If the box is not checked, individual socket will be executed once the button that contains a serial number actual programming socket is clickedClose MaxLoader User’s Guide How to program write one file into different sockets ?EPROM EXAMPLE 1 PROGRAM 8 OF 27128 EPROMS WITH SAME DATA Click for operating all sockets at once, concurrent mode Click for individual socket operationMaxLoader User’s Guide This option is not available for all other devices that are not 8-bit EPROMs. The menu screen below illustrates that there is no Set Program button because the device selected DA28F320J5 is not 8-bit EPROM How to program write buffer blocks data into different sockets ?MaxLoader User’s Guide NOTE Who may need the “set Programming?”MaxLoader User’s Guide Config / Enter Supervisor Mode Config / Enter Production ModeConfig / Language Config / Set Password1. Registration 7. TROUBLE SHOOTING & TECHNICAL SUPPORT2. Software Updates 3. Testing the Hardware4. Quick Self-Diagnostics 5. Contacting Customer Support Electronic Engineering Tools, Inc 6. Service Information4620 Fortran Drive, Suite 102 San Jose, CA 95134, USA. Tel Fax 7. Limited One-Year Warranty MaxLoader User’s Guide 8. Useful Web Site Addresses/ Phone NumbersOptional EPROM Emulator 9. Programming Adapter Manufacturers10. EPROM Emulator Manufacturers 8. OTHER PRODUCTSComparison of NOR and NAND Flash technologies 9. ABOUT NAND FLASH MEMORYMaxLoader User’s Guide How to Program NAND Flash Why NAND FlashMaxLoader User’s Guide Blank Check How to READ NAND Flash10. GLOSSARY Bipolar PROMGang Programmer FPGAFunctional Test FuseMemory device HEX fileJEDEC JEDEC filePackage MicrocontrollerNon-Volatile OscillatorSOIC PQFPSerial Memory Socket moduleWord width TSOPUV Erasable Verify