Select Product | IBM MaxLoader specs

MaxLoader User’s Guide

NOTE: For the latest software upgrade, remove the old MaxLoader in “Add/Remove Program” of “Setting / Control Panel” in 2000/XP/VISTA before installing a new MaxLoader in your PC.

Select Product

After MaxLoader is installed, choose a programmer among TopMax, TopMax- 8G, ChipMax/ChipMax2, TopMaxII, UniMax, and ProMax8G (4G) hardware in the very first MaxLoader screen menu. Or Click on Config / Select product Make sure to select the right model and turn the switch on. (TopMaxII, ProMax, TopMax) or connect the AC cord (UniMax, ChipMax/ChipMax2)

Trouble Shooting In Installation

A communication error may occur on the screen if the hardware / software are not correctly installed.

Be sure that the following steps are checked:

Make sure the USB driver is installed after MaxLoader software is set up in

PC.

18

Image 18

IBM MaxLoader manual Select Product

Contents

MaxLoader User’s Guide Quick Start Examples Device Config Trouble Shooting & Technical Support Other Products About Nand Flash MemoryGlossary Programmer Models for PC USB Interface EE Tools, Inc MaxLoader User’s Guide About This Manual General Description Hardware Installation To Install the software from a CD driveTo Start the windows software MaxLoader User’s Guide MaxLoader User’s Guide MaxLoader User’s Guide MaxLoader User’s Guide MaxLoader User’s Guide MaxLoader User’s Guide To install the Software for parallel port programmers Select Product Families of Programmable Devices NVM Hierarchy Flash Memory Flash Memory Technologies Serial Eeprom Performance ComparisonSerial Flash Eeprom ƒ Xilinx 17xx family Non-Typical Devices 8-bit 1-Megabits Bit 1-Megabits Erasing an Eprom PLD Features Microcontroller About Device ID and Auto Select on EE Tools programmers Auto Select To Find a Device ID Safety Note Conventions Other terms and definitions are as follows Choosing a Right Adapter Different Device Packages Different Programming Adapters Quick Start Examples Programming an Eprom with data MaxLoader User’s Guide Duplicating an Eprom from a master IC device Source Device Programmed AMD 27C256 Basic Menu Screen Information Option Information Target Device Erased or blank Intel 27C256Split Additional Option Information for Non PLD Devices System InformationCounter Verification error File ƒ Binary Format ƒ Intel HEX Format ƒ Motorola S HEX Format ƒ Tektronix HEX Format 00001102444154414D414E2053332053455249414C8F 01000001 ƒ Jedec Standard PLD devices only ETX Sum Check ƒ POF file Altera EPMxxx devices only File / Load File / Reload File/ Load Project File/ Save Project File/ Save Log File/ Save All Messages Buffer Asc Data looking for Ascii value Buffer / Edit BufferFind HEX Find Next Fill BufferFill random data Copy buffer Clear buffer Set editor to view mode Print buffer Set editor to edit mode Set Editor to binary mode Set editor to 8 bitbyte Hex Set editor to 16 bitword Hex Set default editor mode Set editor to 32 bitdouble word Hex Set default Reset Editor Swap nibble Swap byte Swap Word Swap double word Jedec editor Clear Close Buffer / Edit UES Device / Select by history Select ƒ Select / E EPROM, Flash Select / Auto Select Select / Device information Device / Change Algorithm Device / Auto Menu Option Device / Blank Check MaxLoader User’s Guide ƒ Programmable Logic Device operation Device / Programƒ Memory device ƒ 28C256, 28C010, etc ƒ Microchip PIC devices Copy from a master chip to a new chip ƒ Motorola MC68HC908 devices ƒ Serial EEPROMsƒ Atmel or Xilinx Device / Read Device / Verify Device / Data Compare Device / EraseDevice / Security Device / Encryption Device / Option Dram types tested Device / AutoTest / RAM Test Sram type tested Test / Vector Test Optional Operation Value DelayTest / IC Test Vcc Config / Select Product Test Config / Config Option Config Option / Buffer Clear Before File Loading Config Option / verify after programming Config Option / Blank Check Before ProgrammingConfig Option / Verify After Reading Config Option / Byte order swapping Byte swap = disabled Cursor AT Location 00000000 8 BIT Addressing Config Option / Device Insert Test Config Option / Device ID Check Config Option / Sound Config Option / Default Buffer ValueConfig Option / 32 Bit Checksum Config Option / Port TopMax, ChipMax Config Option / USB Option USB programmer USB option / Enable Start button USB option / Enable Start ALL button Enabling #4 socket to be master socketUSB option / Good LED off on socket open Config Option / Gang Split Select Split Byte $0001 Byte $0003 Config Option / Address Device Address File Load Config Option / Auto Inc File Save Config / Concurrent gang mode Config / Hardware test MaxLoader User’s Guide Enabling any button to be a Start Key Close How to program write one file into different sockets ? Example 1 Program 8 of 27128 Eproms with Same Data MaxLoader User’s Guide MaxLoader User’s Guide Example 2 SET Program for 8 of 27128 Eproms MaxLoader User’s Guide Config / Enter Production Mode Config / Enter Supervisor Mode Config / Set Password Config / Language Software Updates Testing the HardwareRegistration Quick Self-Diagnostics Contacting Customer Support Service Information Electronic Engineering Tools, Inc Limited One-Year Warranty Useful Web Site Addresses/ Phone Numbers Programming Adapter Manufacturers Eprom Emulator Manufacturers About Nand Flash Memory Why Nand Flash How to Program Nand Flash How to Read Nand Flash BGA DIP FpgaGAL Jedec file HEX fileJedec LCC OTP PGAPlcc RAM PqfpQFP ROM UV Erasable TQFTsop Verify