Buffer / Edit Buffer, Find, Hex | IBM MaxLoader guide

MaxLoader User’s Guide

Buffer / Edit Buffer

This command allows the user to examine and modify the contents of the memory buffer. This section applies to a non-JEDEC file (PROM, EPROM, EEPROM, and Microcontroller) or to a memory chip. If a PLD is being loaded, see the (vector pattern edit) section. The data is presented in HEX and ASCII formats.

Find

This feature allows you to search the data (ASCII and HEX) in the current

Asc	: The data looking for ASCII value.
HEX	: The data looking for HEX value.

Direction / UP : The data searching from previous address than the current location.

Direction / DOWN: The data searching from higher address than the current location.

If you would like to see more & same data, click on the Find Next button.

49

Image 49

IBM MaxLoader manual Buffer / Edit Buffer, Find, Asc Data looking for Ascii value, Hex, Data looking for HEX value

Contents

MaxLoader User’s Guide Quick Start Examples Device Config Trouble Shooting & Technical Support About Nand Flash Memory Other ProductsGlossary EE Tools, Inc Programmer Models for PC USB Interface MaxLoader User’s Guide General Description About This Manual To Install the software from a CD drive Hardware InstallationTo Start the windows software MaxLoader User’s Guide MaxLoader User’s Guide MaxLoader User’s Guide MaxLoader User’s Guide MaxLoader User’s Guide MaxLoader User’s Guide To install the Software for parallel port programmers Select Product NVM Hierarchy Families of Programmable Devices Flash Memory Flash Memory Technologies Serial Flash Eeprom Performance ComparisonSerial Eeprom ƒ Xilinx 17xx family Non-Typical Devices 8-bit 1-Megabits Erasing an Eprom Bit 1-Megabits PLD Features Microcontroller Auto Select About Device ID and Auto Select on EE Tools programmers To Find a Device ID Other terms and definitions are as follows Safety Note Conventions Choosing a Right Adapter Different Device Packages Different Programming Adapters Programming an Eprom with data Quick Start Examples MaxLoader User’s Guide Source Device Programmed AMD 27C256 Duplicating an Eprom from a master IC device Target Device Erased or blank Intel 27C256 Basic Menu Screen Information Option InformationSplit System Information Additional Option Information for Non PLD DevicesCounter File Verification error ƒ Binary Format ƒ Intel HEX Format ƒ Motorola S HEX Format 00001102444154414D414E2053332053455249414C8F 01000001 ƒ Tektronix HEX Format ƒ Jedec Standard PLD devices only Sum Check ETX File / Load ƒ POF file Altera EPMxxx devices only File / Reload File/ Save Project File/ Load Project File/ Save Log File/ Save All Messages Buffer Find Buffer / Edit BufferAsc Data looking for Ascii value HEX Fill Buffer Find NextFill random data Copy buffer Clear buffer Print buffer Set editor to view mode Set Editor to binary mode Set editor to edit mode Set editor to 16 bitword Hex Set editor to 8 bitbyte Hex Set editor to 32 bitdouble word Hex Set default editor mode Swap nibble Set default Reset Editor Swap Word Swap byte Jedec editor Swap double word Clear Buffer / Edit UES Close Device / Select by history Select Select / Auto Select ƒ Select / E EPROM, Flash Select / Device information Device / Change Algorithm Device / Blank Check Device / Auto Menu Option MaxLoader User’s Guide ƒ Memory device Device / Programƒ Programmable Logic Device operation ƒ 28C256, 28C010, etc Copy from a master chip to a new chip ƒ Microchip PIC devices ƒ Serial EEPROMs ƒ Motorola MC68HC908 devicesƒ Atmel or Xilinx Device / Verify Device / Read Device / Erase Device / Data CompareDevice / Security Device / Option Device / Encryption Test / RAM Test Device / AutoDram types tested Sram type tested Test / Vector Test Test / IC Test DelayOptional Operation Value Vcc Test Config / Select Product Config Option / Buffer Clear Before File Loading Config / Config Option Config Option / Verify After Reading Config Option / Blank Check Before ProgrammingConfig Option / verify after programming Config Option / Byte order swapping Cursor AT Location 00000000 8 BIT Addressing Byte swap = disabled Config Option / Device ID Check Config Option / Device Insert Test Config Option / Default Buffer Value Config Option / SoundConfig Option / 32 Bit Checksum Config Option / Port TopMax, ChipMax USB option / Enable Start button Config Option / USB Option USB programmer Enabling #4 socket to be master socket USB option / Enable Start ALL buttonUSB option / Good LED off on socket open Config Option / Gang Split Select Byte $0001 Byte $0003 Split Config Option / Address File Load Device Address File Save Config Option / Auto Inc Config / Hardware test Config / Concurrent gang mode MaxLoader User’s Guide Enabling any button to be a Start Key Close How to program write one file into different sockets ? Example 1 Program 8 of 27128 Eproms with Same Data MaxLoader User’s Guide MaxLoader User’s Guide Example 2 SET Program for 8 of 27128 Eproms MaxLoader User’s Guide Config / Enter Supervisor Mode Config / Enter Production Mode Config / Language Config / Set Password Testing the Hardware Software UpdatesRegistration Quick Self-Diagnostics Contacting Customer Support Electronic Engineering Tools, Inc Service Information Limited One-Year Warranty Useful Web Site Addresses/ Phone Numbers Eprom Emulator Manufacturers Programming Adapter Manufacturers About Nand Flash Memory How to Program Nand Flash Why Nand Flash BGA How to Read Nand Flash Fpga DIPGAL Jedec HEX fileJedec file LCC PGA OTPPlcc QFP PqfpRAM ROM Tsop TQFUV Erasable Verify