Appendix B Connections and Pinouts | Lantronix 900-653-R specification

Appendix B: Connections and Pinouts

The xDirect has a DB9F DCE connector, and an Ethernet 10/100 RJ45 interface. The xDirect can be powered via a mini USB-B jack with a provided 5 VDC power supply, or Ethernet PoE (hardware optional), or DB9F pin 9 and 5.

Figure B-1 Single Serial Port and Ethernet Port on xDirect

Serial Port Pinouts

The xDirect has one female DB9 DCE serial port that supports one of three pinouts depending on the model of your xDirect unit:

Figure B-2 DB9F in RS232 Mode (All Models)

Figure B-3 DB9F in RS422/485 (4-Wire) Mode (xDirect485 & PoE Models)

xDirect User Guide

Page 72

Image 72

Lantronix 900-653-R manual Appendix B Connections and Pinouts, Serial Port Pinouts

Contents

User Guide Warranty Copyright & TrademarkContacts Disclaimer Table of Contents Using this GuideInstallation of xDirect Using DeviceInstaller Configuration Using Web Manager Configuration Via Telnet or Serial Port Setup Mode Setup Mode Server Configuration Setup Mode Channel Configuration Setup Mode Advanced Settings Firmware UpgradesMonitor Mode Appendix a Troubleshooting and Contact Info Appendix B Connections and PinoutsAppendix E Binary to Hexadecimal Conversions Appendix F Compliance List of Figures Serial Tunneling Example List of Tables Using this Guide Purpose and AudienceChapter Summary Additional Documentation Document Description Key Features IntroductionApplications Introduction Additional Features Configuration MethodsProtocol Support Product Information Label Product Label Installation of xDirect Package ContentsInstalling the xDirect Required Information Hardware AddressIP Address Using DeviceInstaller Installing DeviceInstallerTo install DeviceInstaller Assigning an IP Address Accessing the xDirect Using DeviceInstaller Viewing the Current ConfigurationTo view the units current settings XDirect Configuration in DeviceInstaller Supports Configurable Pins CommentsDevice Family Type Assigning the IP Address Serial Port Login Next Step Configuration Using Web Manager Accessing xDirect Using DeviceInstaller Configuration Using Web Manager Network Configuration Network ModeAutomatic IP Address Configuration To assign an IP address automatically Static IP Address Configuration Ethernet ConfigurationSelect Use the following IP configuration To assign an IP address manually Server Configuration To configure the xDirect device server settings Monitor Mode @ Bootup CPU Performance ModeConfig Server Port Timeout ms Host List Configuration To configure the host listRetry Timeout Retry Counter Channel 1 Configuration Serial SettingsTo configure the channel’s serial settings Enable Packing Baud RateData Bits Parity Connection Settings TCP To configure a channel’s TCP settingsAccept Incoming Password Required Modem ModeModem Escape Sequence Pass Through Connection Settings UDP To configure a channel’s UDP settings Datagram Type Use BroadcastDevice Address Table Apply Settings Apply Defaults Configuration Via Telnet or Serial Port Setup Mode Accessing Setup ModeTelnet Connection To establish a Telnet connection Password Press Enter for Setup Mode Exiting Setup Mode Two options through which to exit setup modeSerial Port Connection Setup Mode Server Configuration Server Configuration OptionBootP/DHCP/AutoIP options IP Address Set Gateway IP Address Netmask Number of Bits for Host PartSet DNS Server IP Address Standard IP Network Netmasks Change Telnet Configuration Password Dhcp Name Setup Mode Channel Configuration Channel 1 OptionBaudrate Interface Mode Interface Mode OptionsCommon Interface Mode Settings Flow Connect Mode Port NumberFlow Control Options Reserved Port Numbers Connect Mode Options Connect Mode OptionIncoming Connection Response Active StartupManual Connection Address Example Host List Option Hostlist C0.0.0.0/0Autostart Automatic Connection Modem Mode To enable the hostlistDatagram Type Directed UDP Modem Mode Messages Message Meaning Send the Escape Sequence +++ in Modem Mode 10 Modem Mode CommandsModem Mode Function Command Show IP Address after Ring Disconnect Mode DisConnMode Auto Increment Source PortRemote IP Address Remote Port Flush Mode Buffer Flushing 11 Disconnect Mode Options12 Flush Mode Options Pack Control Packing IntervalTrailing Characters Send Characters DisConnTime Inactivity Timeout Channel Port PasswordSend Characters Telnet Terminal Type Setup Mode Advanced Settings Expert Settings OptionARP Cache Timeout In Seconds TCP Keepalive Time In Seconds Security Settings Option Disable Snmp Disable Telnet SetupSnmp Community Name Disable Tftp Firmware Update Disable Port 77FE HexDisable Web Server Disable Web Setup Default Settings Option Enable Enhanced Password Channel 1 Configuration Defaults Expert Settings DefaultsSecurity Settings Defaults Setup Mode Advanced Settings Firmware Upgrades Using Tftp Graphical User InterfaceObtaining Firmware Reloading Firmware Firmware Files Using Tftp Command Line Interface To recover firmware Firmware Upgrades Monitor Mode Entering Monitor Mode Using the Serial PortEntering Monitor Mode Using the Network Port To enter Monitor Mode locally Monitor Mode Commands Monitor Mode CommandsCommand Command Name Function G0, G1, ....,Ge, Gf Command Response Codes Response Meaning Appendix a Troubleshooting and Contact Info LEDsStatus LED Table A-2 Status LED Problems and Error Messages Serial LEDsRJ45 Ethernet LED Using DeviceInstaller Serial Settings on page 29 or Technical Support United StatesEurope, Middle East and Africa Appendix B Connections and Pinouts Serial Port Pinouts Ethernet Connector Pinouts Table B-6 Ethernet RJ45 Connector Pin-Outs Power Jack Mini USB-B Appendix C Technical Specifications Table C-1 xDirect Technical SpecificationsCategory Description Appendix C Technical Specifications Appendix D Alternative Ways to Assign an IP Address AutoIP ARP and Telnet To assign a temporary IP address Appendix E Binary to Hexadecimal Conversions Converting Binary to HexadecimalConversion Table Scientific Calculator Appendix E Binary to Hexadecimal Conversions Safety Appendix F ComplianceManufacturer’s Name & Address Electromagnetic Emissions Appendix F Compliance RoHS Notice