Power Jack Mini USB-B | Lantronix 900-653-R guide

Appendix B: Connections and Pinouts

Power Jack (Mini USB-B)

The 5 VDC power supply included with standard xDirect devices (and not included the xDirect PoE model) connects to standard xDirect units through a mini USB connector on the side of the device.

Figure B-7 Mini USB Power Port Connector on Standard xDirect Units

xDirect User Guide

Page 74

Image 74

Lantronix 900-653-R manual Power Jack Mini USB-B

Contents

User Guide Contacts WarrantyCopyright & Trademark Disclaimer Installation of xDirect Table of ContentsUsing this Guide Using DeviceInstaller Configuration Using Web Manager Configuration Via Telnet or Serial Port Setup Mode Setup Mode Server Configuration Setup Mode Channel Configuration Monitor Mode Setup Mode Advanced SettingsFirmware Upgrades Appendix E Binary to Hexadecimal Conversions Appendix a Troubleshooting and Contact InfoAppendix B Connections and Pinouts Appendix F Compliance List of Figures Serial Tunneling Example List of Tables Chapter Summary Using this GuidePurpose and Audience Additional Documentation Document Description Applications Key FeaturesIntroduction Introduction Protocol Support Additional FeaturesConfiguration Methods Product Information Label Product Label Installing the xDirect Installation of xDirectPackage Contents IP Address Required InformationHardware Address To install DeviceInstaller Using DeviceInstallerInstalling DeviceInstaller Assigning an IP Address To view the units current settings Accessing the xDirect Using DeviceInstallerViewing the Current Configuration XDirect Configuration in DeviceInstaller Device Family Supports Configurable PinsComments Type Assigning the IP Address Serial Port Login Next Step Configuration Using Web Manager Accessing xDirect Using DeviceInstaller Configuration Using Web Manager Automatic IP Address Configuration Network ConfigurationNetwork Mode To assign an IP address automatically Select Use the following IP configuration Static IP Address ConfigurationEthernet Configuration To assign an IP address manually Server Configuration To configure the xDirect device server settings Config Server Port Monitor Mode @ BootupCPU Performance Mode Timeout ms Retry Timeout Host List ConfigurationTo configure the host list Retry Counter To configure the channel’s serial settings Channel 1 ConfigurationSerial Settings Data Bits Enable PackingBaud Rate Parity Accept Incoming Connection Settings TCPTo configure a channel’s TCP settings Modem Escape Sequence Password RequiredModem Mode Pass Through Connection Settings UDP To configure a channel’s UDP settings Device Address Table Datagram TypeUse Broadcast Apply Settings Apply Defaults Telnet Connection Configuration Via Telnet or Serial Port Setup ModeAccessing Setup Mode To establish a Telnet connection Password Press Enter for Setup Mode Serial Port Connection Exiting Setup ModeTwo options through which to exit setup mode BootP/DHCP/AutoIP options Setup Mode Server ConfigurationServer Configuration Option IP Address Set DNS Server IP Address Set Gateway IP AddressNetmask Number of Bits for Host Part Standard IP Network Netmasks Change Telnet Configuration Password Dhcp Name Baudrate Setup Mode Channel ConfigurationChannel 1 Option Common Interface Mode Settings Interface ModeInterface Mode Options Flow Flow Control Options Connect ModePort Number Reserved Port Numbers Incoming Connection Connect Mode OptionsConnect Mode Option Manual Connection Address Example ResponseActive Startup Autostart Automatic Host List Option HostlistC0.0.0.0/0 Connection Datagram Type Modem ModeTo enable the hostlist Directed UDP Modem Mode Messages Message Meaning Modem Mode Function Command Send the Escape Sequence +++ in Modem Mode10 Modem Mode Commands Show IP Address after Ring Remote IP Address Disconnect Mode DisConnModeAuto Increment Source Port Remote Port 12 Flush Mode Options Flush Mode Buffer Flushing11 Disconnect Mode Options Trailing Characters Pack ControlPacking Interval Send Characters Send Characters DisConnTime Inactivity TimeoutChannel Port Password Telnet Terminal Type ARP Cache Timeout In Seconds Setup Mode Advanced SettingsExpert Settings Option TCP Keepalive Time In Seconds Security Settings Option Snmp Community Name Disable SnmpDisable Telnet Setup Disable Web Server Disable Tftp Firmware UpdateDisable Port 77FE Hex Disable Web Setup Default Settings Option Enable Enhanced Password Security Settings Defaults Channel 1 Configuration DefaultsExpert Settings Defaults Setup Mode Advanced Settings Obtaining Firmware Reloading Firmware Firmware UpgradesUsing Tftp Graphical User Interface Firmware Files Using Tftp Command Line Interface To recover firmware Firmware Upgrades Entering Monitor Mode Using the Network Port Monitor ModeEntering Monitor Mode Using the Serial Port To enter Monitor Mode locally Command Command Name Function Monitor Mode CommandsMonitor Mode Commands G0, G1, ....,Ge, Gf Command Response Codes Response Meaning Status LED Appendix a Troubleshooting and Contact InfoLEDs Table A-2 Status LED RJ45 Ethernet LED Problems and Error MessagesSerial LEDs Using DeviceInstaller Serial Settings on page 29 or Europe, Middle East and Africa Technical SupportUnited States Appendix B Connections and Pinouts Serial Port Pinouts Ethernet Connector Pinouts Table B-6 Ethernet RJ45 Connector Pin-Outs Power Jack Mini USB-B Category Description Appendix C Technical SpecificationsTable C-1 xDirect Technical Specifications Appendix C Technical Specifications Appendix D Alternative Ways to Assign an IP Address AutoIP ARP and Telnet To assign a temporary IP address Conversion Table Appendix E Binary to Hexadecimal ConversionsConverting Binary to Hexadecimal Scientific Calculator Appendix E Binary to Hexadecimal Conversions Manufacturer’s Name & Address SafetyAppendix F Compliance Electromagnetic Emissions Appendix F Compliance RoHS Notice