Lantronix 900-653-R - page 37

6: Configuration Via Telnet or Serial Port (Setup Mode)

xDirect User Guide 37

Password :----

Press Enter for Setup Mode

3. Enter User Name (user name is admin and cannot be changed). Pressing the Enter key after

entry is not necessary. The Password field will appear.

4. Enter Password (default password is PASS). Pressing the Enter key after entry is not

necessary. You will be prompted to enter Setup Mode.

Note: Password can be modified or disabled. See Server Configuration (on page 26).

5. To enter Setup Mode, press Enter within 5 seconds. The configuration settings display (see

Figure 6-2), followed by the Change Setup menu.

Figure 6-2 Setup Menu Options

*** basic parameters

Hardware: Ethernet TPI

IP addr - 0.0.0.0/DHCP/BOOTP/AutoIP, no gateway set

DNS Server not set

Telnet config password set

DHCP device name : not set

DHCP FQDN option: Disabled

*** Security

SNMP is enabled

SNMP Community Name: public

Telnet Setup is enabled

TFTP Download is enabled

Port 77FEh is enabled

Web Server is enabled

Web Setup is enabled

ECHO is disabled

Encryption is disabled

Enhanced Password is disabled

*** Channel 1

Baudrate 9600, I/F Mode 4C, Flow 00

Port 10001

Connect Mode : C0

Send ‘+++’ in Modem Mode enabled

Show IP addr after ‘RING’ enabled

Auto increment source port disabled

Remote IP adr: --- none ---, Port 00000

Disconn Mode : 00

Flush Mode : 00

*** Expert

TCP Keepalive : 45s

ARP cache timeout: 600s

CPU performance: Regular

Monitor Mode @ bootup : enabled

HTTP Port Number : 80

MTU Size: 1400

Contents

Main Copyright & Trademark Warranty Contacts Disclaimer Revision History Table of Contents 1: Using this Guide 10 2: Introduction 12 3: Installation of xDirect 16 4: Using DeviceInstaller 18 5: Configuration Using Web Manager 22 6: Configuration Via Telnet or Serial Port (Setup Mode) 36 7: Setup Mode: Server Configuration 39 8: Setup Mode: Channel Configuration 42 9: Setup Mode: Advanced Settings 55 10: Firmware Upgrades 61 11: Monitor Mode 64 Page List of Figures List of Tables xDirect User Guide 10 1: Using this Guide Purpose and Audience Chapter Summary The remaining chapters in this guide include: Additional Documentation 2: Introduction Key Features Applications Page Protocol Support Additional Features Configuration Methods Product Information Label 3: Installation of xDirect Package Contents Installing the xDirect Required Information Hardware Address IP Address 4: Using DeviceInstaller Installing DeviceInstaller Assigning an IP Address Adding the Unit to the Manage List Accessing the xDirect Using DeviceInstaller Viewing the Current Configuration 4: Using DeviceInstaller xDirect User Guide 20 Next Step Assigning the IP Address: Serial Port Login 5: Configuration Using Web Manager Accessing xDirect Using DeviceInstaller Page Network Configuration Network Mode Automatic IP Address Configuration Static IP Address Configuration Ethernet Configuration Server Configuration xDirect User Guide 27 3. When you are finished, click the OK button. 4. On the main menu, click Apply Settings. Host List Configuration Channel 1 Configuration Serial Settings xDirect User Guide 30 Pack Control Flush Output Buffer (Network to Serial) Flush Input Buffer (Serial to Network) Connection Settings - TCP xDirect User Guide 32 Connect Mode: Active Connection Common Options Endpoint Configuration Connection Settings - UDP Page Page 6: Configuration Via Telnet or Serial Port (Setup Mode) Accessing Setup Mode Telnet Connection Page Serial Port Connection Exiting Setup Mode 7: Setup Mode: Server Configuration Server Configuration (Option 0) IP Address Set Gateway IP Address Netmask: Number of Bits for Host Part Set DNS Server IP Address Change Telnet Configuration Password DHCP Name 8: Setup Mode: Channel Configuration Channel 1 (Option 1) Baudrate I/F (Interface) Mode Flow Port Number Connect Mode 8: Setup Mode: Channel Configuration a) Incoming Connection xDirect User Guide 45 8: Setup Mode: Channel Configuration xDirect User Guide 46 b) Response Table 8-7 Manual Connection Address Example c) Active Startup Host List Option (Hostlist) d) Datagram Type e) Modem Mode Page Send the Escape Sequence (+++) in Modem Mode Show IP Address after 'RING' Auto Increment Source Port Remote IP Address Remote Port Disconnect Mode (DisConnMode) Flush Mode (Buffer Flushing) Pack Control Packing Interval Trailing Characters Send Characters DisConnTime (Inactivity Timeout) Send Characters Telnet Terminal Type Channel (Port) Password 9: Setup Mode: Advanced Settings Expert Settings (Option 5) TCP Keepalive Time In Seconds ARP Cache Timeout In Seconds CPU Performance Security Settings (Option 6) Disable SNMP SNMP Community Name Disable Telnet Setup Disable TFTP Firmware Update Disable Port 77FE (Hex) Disable Web Server Disable Web Setup Disable ECHO Ports Default Settings (Option 7) 9: Setup Mode: Advanced Settings xDirect User Guide 60 Channel 1 Configuration Defaults Expert Settings Defaults Security Settings Defaults 10: Firmware Upgrades Obtaining Firmware Reloading Firmware Using TFTP: Graphical User Interface Using TFTP: Command Line Interface Recovering the Firmware Using the Serial Port and DeviceInstaller Page 11: Monitor Mode Entering Monitor Mode Using the Serial Port Entering Monitor Mode Using the Network Port Monitor Mode Commands Page Appendix A: Troubleshooting and Contact Info LEDs Status LED xDirect User Guide 68 Serial LEDs Problems and Error Messages Table A-4 Ethernet Link LED Table A-5 Ethernet Activity LED Page Page Technical Support Appendix B: Connections and Pinouts Serial Port Pinouts Ethernet Connector Pinouts Page xDirect User Guide 75 Appendix C: Technical Specifications Table C-1 xDirect Technical Specifications Appendix C: Technical Specifications xDirect User Guide 76 Appendix D: Alternative Ways to Assign an IP Address DHCP AutoIP BOOTP ARP and Telnet Appendix E: Binary to Hexadecimal Conversions Converting Binary to Hexadecimal Conversion Table Scientific Calculator Page Appendix F: Compliance Appendix F: Compliance xDirect User Guide 82